Counting matching models…
I modified the Rookery by Gulsifer to fit dual 4020 and 5015 blower fans instead of the original 3010 and 4010 verison. Theres mounting for a accelerometer on both, using M3 heatsets. (15mm holespacing) The 4020 version comes with some…
This is a mount for a V6 body for the rookery. You need to use the rookery long 4020 for it.
Just a remixed version of the good Rookery 4010 . Adjusted few parts on it to my need for more stability .
Remix of Gulsifer 3010 Rookery Shroud with shorter air ducts
stls for k mount and non. wanted to put the sherpa on my rook build so i came up with this.
In response to a request, I have designed a connection for the rookery tool head to be mounted on an MGN12C linear guideway. Unfortunately, I can't test the design because I don't have an MGN12C lying around at the moment, but according…
From the image, this model is the far left one and is 5mm shorter than the original short version. Remix of https://www.printables.com/@Gulsifer Rookery
Remixed from Gulsifer's Rookery Toolhead and Annex-Engineering's Quickdraw Probe Requires my modded Topframe for added clearance in the Back Uses -4 6x3mm magnets -2 m2 Bolts -1 Omron D2F-5 microswitch -some wires manual attaching It's…
My clone V6 sat to low for the fan duct to work properly, so i raised it by 2mm in PrusaSlicer, the distance can be changed by adjusting the Y position of part4hotend as shown in the picture.
As i often clogged my printer due to my classic stupidity and forgetting mind, i always had to remove the part cooling fans, then the shroud. So i modified it to be removeable without removing any fans! Included the key Kanrog made on my…
A quick and dirty adapter to fit the FYSTEC Portable Input Shaper onto the Rookery. I used 6 mm M3 screws and 1 mm washers to perfectly mount the plastic adapter to the rookery. It's best to screw the adapter in first and then mount the…
I have adapted the rookery to fit a mosquito hotend that I had laying around. I used a threaded bowden tube coupler on the top of the adapter since there is no bowden version of the mosquito that I'm aware of. Its shorter that the…
My clone V6 sat to low for the fan duct to work properly, so i raised it by 2mm in PrusaSlicer, the distance can be changed by adjusting the Y position of part4hotend as shown in the picture.
A quick and dirty adapter to fit the FYSTEC Portable Input Shaper onto the Rookery. I used 6 mm M3 screws and 1 mm washers to perfectly mount the plastic adapter to the rookery. It's best to screw the adapter in first and then mount the…
I modified Gulsifer's fan shroud and V6 CHC clamp so that I could mount my Revo Six(clone) hotend to my rook. Why a Revo Six? It was the hotend I had spare for this project (Rook MK1.1) and thought I'd share it for others who'd like to do…
I have adapted the rookery to fit a mosquito hotend that I had laying around. I used a threaded bowden tube coupler on the top of the adapter since there is no bowden version of the mosquito that I'm aware of. Its shorter that the…
This is a tool head designed for an ender head with a volcano heat block. here is the BOM (1) 3010 fan (2) 3010 blowers or 4010 blowers (3) M3x6x5 heat inserts (2) M3x4x5 heat inserts for input shaper - Optional (2) M3x4x5 heat inserts…
I put M3 nut holders into the model and tightened up the nutsert hols to make them M3 clearance holes. I'm using this to hold the short 5015 fan shroud. The nuts should be fully seated before attaching the cradle to the carriage. I use a…
The original part has already broken twice in the same place. Both times after about a month of use. (With normal use --> approx. 20h per week printing time) I then decided to make a few minor changes to the original part. I added a…
As im building a larger, scalable Rook 2020 , i want more space, but don't want to loose the opportunity to use the rookery , as the mounting-system for it is pretty genius! I've made a wider base with additional holes at the bottom to…
i made this because i was too lazy to move the hole. (original made by Gulsifer)
This is a Rookery bowden tool head with a added rgb neopixel inside behind the logo on the rookery. It uses a ldo kirigami pcb that has been cut down to fit inside of it it is held on by one m3x5 screw and a 3x4x5 heat insert. For the…
This design allows an x1c hotend (or its clone) to be installed on the Rook MK1 with the original Rookery cradle. Considering how affordable and well the official Bambu Lab hotend is, it is a great hotend option for the Rook. Parts for…
Just a fan guard for the rookery hotend, still heaps of air flow.
This is for Mellow's NF crazy Volcano Heater Block with the mosquito clone hotend. Based on the 5015 version in the step file of the original uploader. Unlike the other, that has 2 extra hole on the side for extra screws. Include version…
If you like the aesthetic of the original Rookery, but want to cram in a bunch more stuff, this might be the toolhead for you. Takes a rookery, makes it a bit taller, a lot wider, and a bit heavier. The tradeoff is you can fit a micro…
![Rookery Belt Cradle reinforced [MGN12C]](https://media.printables.com/media/prints/542109/images/4363651_f9f4b947-1499-4be7-87f0-3a4951fefea3/mgn12c-belt-cradle_remix-2.png)
![Magprobe for Rook [MK1] with Rookery Toolhead](https://media.printables.com/media/prints/404666/images/3368998_6796c868-2b43-4565-9c45-39d81752675f/img-7535.jpg)
![Rookery Belt Cradle reinforced [MGN09C]](https://media.printables.com/media/prints/439774/images/3647887_85dece12-6dee-4f5c-bfe4-5480fa443029/belt-cradle_remix-v4.png)
