46 models
“reduce, reuse, recycle” Verschlussstopfen für gebohrtes 10mm Loch. Macht den Seifenspender nachhaltig nachfüllbar. Schont die Umwelt, spart Plastik und Geld. Looks nice with Prusament Crystal PETG *Anwendung auf eigene Gefahr,…
To save some space, I designed a small pedestal so that the Sagrotan No Touch soap dispenser can stand on the edge of the sink. The width of the sink edge is 36 mm, and the slight incline of the wall was taken into account in the design.…
A simple cover for the SAGROTAN soap dispenser. By the way, you can find a shelf for wall mounting in my 3D models . IMPORTANT: YOU ARE NOT ALLOWED TO USE MY DATA FOR COMMERCIAL PURPOSE (E.G. for your ETSY or EBAY) WITHOUT MY CONCENT.…
A new version with a different thread and some fixes. If the outer diameter of your outlet is 12.2mm (the part without the thread) this should work. Do not use much pressure on the bag, First gently squeeze the container to get some air…
Very simple and easy refill-adapter for Sagrotan/Dettol NoTouch soap. no drilling or adding parts to the container needed – the soap container stays unchanged. Simply install the Adapter to the refill bag. It fits the 12,3 mm thread of…
The amount of soap the donor gave me was too much. So I reduced the stroke of the built-in cylinder by bringing the crankshaft bolt closer to the center. In addition the adapter. There is no reason to disturb the electronics! History:…
Layer 0,13 - 0,15 Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0.15 Infill: 20% Filament: PLA Matt Weis Notes: Layer 0,13 - 0,15 Kategorie: Badezimmer
Einfach bei der Sagrotan-Flasche oben ein Loch reinsägen, Deckel aufkleben und mit dem Verschlussdeckel verschliessen. So spart man viel Geld :-) Verschluss benötigt Support.
Here it is! The shelf you've been looking for to secure your SAGROTAN no touch next to your washbasin. You have three options. What all options have in common is the dovetail wall bracket, which should be attached to the wall with either…
This replacement gear has a smaller rotation radius for the pin that moves the soap pump. I reduced the radius to 3.1 mm. After the modification the soap lasts for a very long time compared to the original gear. For easier printing the…
Wollte einen Deckel den man nicht kleben muss. Einfach mittig ein Loch (Durchmesser 20mm) bohren und aufstecken. Drucktipps: PLA Perimeters: 3 20% infill keine Supports nötig!!
Drawn and printed my little one a soap dispenser holder for the Sagrotan. The dispenser base is inserted first and can thus no longer slip out. Then you can put the soap bottle on top. As adhesive tape I used the see link. The holder and…
I stopped uploading and updating my models here at Printables! My actual models can be found on my MakerWorld profile – with print profiles. Take care to use the newest models … I used Klexer's model , but I always had to remove the soap…
Im Bad hatte ich zwei Bohrungen im Abstand von 2,7cm, die mich irgendwie immer geärgert haben und einen Seifenspender der beim putzen immer im Weg steht. Also überlegte ich, wie ich beides zufriedenstellend beheben kann. Herausgekommen…
SAGROTAN Seifenspender Verschluss-Stoppel um selbst Seife nachfüllen zu können. Kann natürlich auch für andere Seifenspender verwendet werden. Es muss dazu nur ein Loch in den Seifenbehälter gebohrt werden. Stoppel rein. Fertig.
Einfacher Wandhalter für einen Sagrotan no touch Seifenspender. Zum Kleben an die Wand habe ich das hier verwendet UHU 45450 Doppel-Strips Extrem, 4 kg, 26 mm x 31 mm, 16 Stück…
Easy to print! Just print it upside down with your favorite filament and enjoy the maritime look. I have adjusted the model so that it can be printed seamlessly in a single color while remaining a single file/body. However, it is still…
The idea is simple - just print the 2 parts. The first insert screws into a 20 mm hole that you drill into the top of the empty container. I would recommend to glue it in with some super glue or 5 minute epoxy to secure and seal the fit.…
This way you customize the last Dettol/Sagrotan refill unit you'd be buying, into a truly unlimited refill. Also, you reduce plastic waste in long term. You can then freely refill it with any of the liquid soaps that you would buy in bulk…
A holder for the Sagrotan No Touch soap dispenser. There is a stand and a wall mount. Both have the option of a small drip tray. The wall mount is hidden behind the holder which slides on the tapered dovetail. For the mount there is a…
The Sagrotan/Dettol soap dispensers are very simple contraptions inside. In effect, a single cog determines how much soap is pulled/pushed by the moving piston. Originally, the cog moving the piston has a pin that is offset by 6mm,…
Want to save money on your Sagrotan soap refill? Just drill a hole into the top of the original soap container to use cheaper refill soap. 3D print the provided plug in TPU to tightly seal the hole. I used a step drill to drill a 18mm…
A Holder for the Sagrotan / Dettol No Touch Soap Dispenser. There are two models for mounting or placing: One for mounting (glue) / placing with a soap tray and one without a soap tray. One for screwing with a soap tray and one without a…
Deckel für No-Touch Nachfüller. Einfach Loch in den Nachfüller und Deckel drauf.
Wall mount for the Sagrotan No Touch soap dispenser. While the mounting plate that is permanently attached to the wall, the holder can be easily removed for cleaning and be re-attached.
Ich habe für den Seifenspender von Sagrotan eine simple Halterung designed. Es gibt zwei Varianten, eine zum Kleben und eine zum Schrauben. Druck ohne Supports mit ca 10% Infill hat bei mir prima geklappt I designed a holder for…
Housing for Sagrotan No-Touch Dispensor. So that the case doesn't look too big, I designed it so that the No-Touch only fits in WITHOUT the battery cover. Printed without supports on Prusa mk4 and Prusa XL.
Der Sagrotan Verschluss besteht aus dem Stöpsel und dem Grundteil damit er auch verschraubt werden kann. Eine Schablone ist auch dabei (zuerst 16mm Loch bohren) danach Schablone drauf und damit die 5mm Bohrung machen. Den Deckel hab ich…
🌱 Nachhaltiger Verschluss für Sagrotan "no touch" Flaschen 🌱 Mit diesem innovativen Verschluss für die Sagrotan "no touch" Flaschen ist es möglich, die vorhandene Flasche einfach und nachhaltig wiederzuverwenden. Der ökologische Aspekt 🌍…
I designed a simple filler neck for filling soap for the Sagrotan soap dispenser. You only have to drill a 12mm hole and you can click in the socket with a little pressure. Print the parts with a 0.08mm layer height to ensure the…
I remixed the awesome model by joe712 by adding a version without screw holes if you want to glue the dispenser to the wall with e.g. mirror tape. You have to print at least one version of the mount and the drip cup. Best part is still…
Don't throw your money on expensive refill items and enable you to refill using unbranded soap instead by drilling one arbitrary sized hole and after refilling cover it with this lid.
🌱 Sustainable Closure for Sagrotan "no touch" Bottles 🌱 This innovative closure for Sagrotan "no touch" bottles allows for the simple and sustainable reuse of existing bottles. The ecological aspect 🌍 was at the forefront of product…
A small lifehack to be able to fill up your Sagrotan No-Touch soap. Drill a hole on the top of the bottle with a 10mm drill bit Insert the bottom part until you hear a click Insert the top part into the bottom part Now I only had a 10mm…
This is a table mat that fits the original sagrotan soap dispensers. I designed it in a way, that it fits perfectly to the corners of our sink in the kitchen. With it the dispenser stays in place, does not slip around or wobbles on the…
Sagrotan Samt Schaum Pumpkopf
remixed to have less 'sharp' edges Category: Bathroom
I stopped uploading and updating my models here at Printables! My actual models can be found on my MakerWorld profile – with print profiles. Take care to use the newest models … Easy to print, no support needed. I recommend printing a bit…
We have a Sagrotan No-Touch soap dispenser between the wash basins of our dual vanity. Since I was printing a lid anyway, I added a holder for the two basin plugs that had been lying around before. My wife liked it, Mission accomplished.
I stopped uploading and updating my models here at Printables! My actual models can be found on my MakerWorld profile – with print profiles. Take care to use the newest models … Easy to print, no support needed. Overhangs are 40°. I…
Anbei mein Remix von Robert Nickel hinsichtlich einer Halterung für Ikea Tisken und den Sagrotan Seifenspender. Man muss diese in die vier Löcher “einklemmen” mit seinen Füßchen. Dann hält er recht gut. Druck ohne Support mit PLA.
I stopped uploading and updating my models here at Printables! My actual models can be found on my MakerWorld profile – with print profiles. Take care to use the newest models … Best printed as oriented in the STL file. No support needed.
To print it with a SLA printer i combined both files to make one part using 3D builder
Marks the venter of the sagrotan soap dispencer and aneables a 5mm hole beeing drilled.
🌱 Nachhaltiger Verschluss für Sagrotan "no touch" Flaschen 🌱 Mit diesem innovativen Verschluss für die Sagrotan "no touch" Flaschen ist es möglich, die vorhandene Flasche einfach und nachhaltig wiederzuverwenden. Der ökologische Aspekt 🌍…
Don't throw your money on expensive refill items and enable you to refill using unbranded soap instead by drilling one arbitrary sized hole and after refilling cover it with this lid.
