Counting matching models…
Axial SCX6 axle stands; separated by front and rear (since they're different). My goal was to have the strength to hold up a ~28 lbs truck, but use as little filament as possible. You'll need to complete, two rear verticals (they're…
For those you want to track distance, but not be worried about getting your SkyRC GPS wet this is the case for you. I have submerged the case for about 5-min and only experienced very minor water seepage. I wouldn't call this water proof,…
You will need (4) 3mm flat head screws 20mm long to assemble stand together. I printed with 15% infill using PETG and it seems strong enough to hold SCX6.
The panhard bar on the SCX6 is mounted single shear on both ends. No bueno. This brace reinforces the mount on the axle. Uses the stock hardware, no additional parts needed. To reinforce the chassis mount I recommend a metal shock tower…
Axial SCX6 battery extenders for the Gens Ace Bashing Pro 157mm 3S (8000mah and 6700mah) packs and the XL version for Gens Ace Bashing Pro 178mm (15000mah). New - Looking to get these tray extenders, but don't have a printer? Checkout my…
A trailer hitch that bolts up to the SCX6 rear bumper mount without any mods. I broke the ball hitch pretty quickly but it is holding op nicely now in TPU. Required hardware: 4x M4x22mm 1x M2.5x10mm Category: R/C Vehicles
A second valve cover for your SCX6, based on the same thing for an SCX10III. Print without supports, stick on your steering servo with some double sided tape. Category: R/C Vehicles
A Castle Creations Mamba Monster X 8S for the SCX6. This is meant to match up with my receiver box ( here ) and be used with the new 3Brothers RC Black Jacket motors. There's both a lengthwise (LW) and width wise (WW) mount; choose as you…
This receiver cap replaces the stock “engine” cap with a simpler design to allow for better air flow and access to the ESC. With this initial release the stock ESC is still needed though a clip for no ESC (in the stock location) is on the…
front stinger bumper for scx6 honcho with winch cable pass through has 2 different mounting holes for a different look i used the all the way hole to keep it fully flush opens the front wheels way better then the stock bumper fits…
These center caps allow you to use the Injora after-market rims with center caps and still be able to take the lock-nut off and on without taking the 6 center screws out. Depending your printer there's two files - 1mm and 1.25mm, depends…
I purchased some genuine Axial SCX6 body mounts to go with my Pro-Line Racing Cliffhanger body. The body mounts turned out to be a bag of junk, so I decided to design and print my own mounts instead. I designed these for use with the…
This shorty receiver cap replaces the stock “engine” cap with a simpler design to allow for better airflow, access to the ESC and a much lower profile. With this initial release the stock ESC is still needed though a clip for no ESC (in…
Hood louvers for the Axial SCX6. Includes a stencil for cutting out hood material. Print specs used in picture: Filament: PETG Nozzle size: .25
SCX6 cowl GoPro mount. Has room for drilling side holes for light bars or other accessories as well. Uses stock hardware to mount. You'll need: GoPro capture nut 1 x M5 x 20mm 2 x M3 x 10mm socket/cap bolts to secure the insert You'll…
Here is my take on rock lights for the SCX6. These have been out crawling and tested so I’m good with releasing them for everyone! You’ll need to do some printing, drilling and soldering so be prepared. Printing: You’ll need to print all…
lower your scx6 with these shock cups
A quick print that replaces the stock hood vent hold downs with a magnetic clip holder. You'll need: 2 x 15mm x 3mm magnets (Amazon/Ali) - need the ones with a concave in the middle of a M4 screw to go into 2 x M4 x 14/16mm countersunk…
Ever wanted to make your own "litterbuggy"? Your personal trash collecting rc car? Today is your lucky day. All you need is an SCX6, a plastic container and a Prusa Core One L. (If there is interest I can design a model thats printable on…
Axial SCX6 axle stands; separated by front and rear (since they're different). My goal was to have the strength to hold up a ~28 lbs truck, but use as little filament as possible. You'll need to complete, two rear verticals (they're…
Got tired of all the squeaking coming from the Driveshaft. Printed with FPLA This is a first go at it with the materials I had laying around. So far 17 miles after a driveshaft cleaning and no squeaking so far coming from Driveshaft. I…
Here I have a pair of compact battery trays that I made for my SCX6 so I could remove all of the unnecessary factory plastics. The left side tray allows you to run a smaller/ lighter main battery pack. They're designed to suit my 4500mah…
I made this tube rear bumper bar for my SCX6 to suit the Pro-Line Racing Cliffhanger body. It's designed to be similar in styling to the tube front bumper file offered by Pro-Line on their website. I've also included it here too for…
This is a lightweight spare tire cover for the Axial SCX6 Rubicon body. The shell is made up of 2 halves that twist together. My print in PETG weighs 50 grams. The dimensions are based on the stock Rubicon tires size. Included is a blank…
For those not running the "Smart" batteries in their Axial SCX6 trucks; here is a battery monitor mount that you can put in one of your side windows (in my case passenger rear) so that you can monitor your battery voltage. You'll need: 2…
The stock steering on the Axial SXC6 is lacking. One of several issues is the Panhard link setup. This brace will help remove some of the flex in the system. This mounts between the top axel link and the panhard link on the front right…
I travel a lot with my SCX6 in the trunk; it moved around a lot on its tray. Adding these kept it in place. You'll need to print two per wheel; you'll also need some ¼in rope/para-cord to connect them. I found it best to put the chocks…
I ordered an SCX6 trailer hitch but was surprised when it didn't fit my Honcho. So I designed a new rear bumper to make it work. It is modeled around a cheap ali express SCX6 hitch but I think they're all the same. The light holes are…
rear rock lights mount for scx6 honcho with body prop installed will need 1:1 auto cob led dome lights from amazon or ebay there cheap and work on 4s direct power and 2 screws to mount to the rear cross brace just out side the back of the…
A very close to scale SCX6 light pod kit. You'll need the following to make this kit work: 4 x 3mm LEDs 4 x M2 10mm socket head bolts (8mm through 14mm are also ok) 1 x M3 20mm (for holding the pod to the mount) 1 x M3 18mm (or longer)…
