Counting matching models…
v1.1 has better clearances for screw and slot nut variations. You must put the 10mm spacers in to raise the bed before this will fit. Requires M3 v-slot nut, and ~10mm M3 bolt, 2x M3 heatset inserts.
In the video above, I show the issues that I had with the Voron SexBolt Z end stop and how I resolved them with these modifications. Namely, I had interference with the rear print bed mount. Also, due to the print bed insulation I…
This is a remix of the Voron Sexbolt Z endstop for use on my Ender 3 v2. This fits the hartk Z endstop board. I used 2x M4x6 screws and T-Nuts to secure it to the frame to the right of the bed where it can be triggered by the nozzle. The…
there are two versions, hartk version with bushings (sexbolt_upper_mount, sexbolt_lower_mount, sexbolt_torso) v2.4 version with deflanged pulley (nozzle_probe_R1, R2, use sexbolt) auto z calibration should work with short klicky probe, on…
Sexbolt: https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/hartk1213/Voron2.4_SexBolt_ZEndstop Befor you begin, these bed leveling thumb nuts are required:…
I redesigned my scrub brush holder to include a sexbolt mount for auto-z-calibration.
Couldnt find a suitable download for a sexbolt mount for a cr10 so i made this one. Needs 2x M5 16mm Button Head Screws and 2x M5 Locknuts.
(For use with Voron Sexbolt kit parts, also print these adapter parts ) What are klicky and sexbolt? klicky is a magnetic probe that attaches to your toolhead for bed probing. It is lower profile than a bltouch, so it can mount much…
Same BOM as on Github, wiring on the right, to be attach on the outside of the 2020 extrusion.
Remixed to fit ender 3 carriage for my enderwire need 5 m3 heat insert , 3 m3 x 12 bolts and 2 m3x20 bolts and to drill the carriage. Tight fit so just use mount as your drill guide. Print as shown in picture with the 3 heat inserts no…
Z_endstop designed to fit stock ender 5 bed. when used with klipper it can help with z offset calculations. Remix of two designs, voron sexbolt. And a design by carbon neutral.
Introduction I tried the previous design and found my bracket was moving around a bit, and wanted something a bit more sturdy and perhaps simpler if possible. I also wanted something that would work with the Nudge or Sexbolt alignment…
This is an improvement on my last design. It has a tighter fit to the bed bracket preventing any movement.
This is a remix of the Voron mount from Hartk123: https://github.com/hartk1213/MISC/tree/main/Voron%20Mods/Voron%202-Trident/2.4/Voron2.4_SexBolt_ZEndstop I used the hardware kit from KB3D:…
Sexbolt mount for Voron kit Sexbolts, for use with my rigid sexbolt + klicky bed mount design. The original design was intended to use the stock z endstop pcb, this allows you to use the pcb and parts included in Voron Sexbolt kits. 2…
This mod relocates the mellow sexbolt probe uptop the bed extrusions on a V2.4. The primary goal is to make performing tool_offset_calibrate on a Stealthchanger more reliable when tuning z offset where the tool press fully on the probe to…
My Config: [stepper_z] step_pin: PE3 dir_pin: PF13 enable_pin: !PF14 microsteps: 32 rotation_distance: 4 endstop_pin: ^PG10 #position_endstop: 222.0 position_min: -1 position_max: 222 full_steps_per_rotation: 200 homing_retract_dist: 5.0…
push fit. aber kann auch angeschraubt wreden. Idex Pin
Drill-in Ender 3 bed mount. Fits to hartk's SexBolt Z endstop and a custom silicon brush holder included here. The mount is sized to my Ender 3, which uses silicon spaces instead of bed springs, so it may not work on unmodified Ender 3s.…
