Counting matching models…
Hi, thanks for downloading my file! I made this suppressor/silencer for my Novritsch SSG24, because the one Novritsch sold on his website was a bit too expensive for my taste. How it's made This silencer is made up of three easy-to-print…
This bracket is made for 10" racks. They have the standard dimensions of 1U (44.5mm) in height and 250mm in width. With these dimensions the mount can be printed on a print bed with the dimensions of 220mm x 220mm. The mount is designed…
The original design that had a large opening that could potentially let debris inside the operating mechanism. This version closes that up to only what is necessary.
TP-Link Omada ER605 and SG2008P 1U Rack Mount
It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on top or below My print settings layer height: 0.2 wall: 3 infill: 15% If…
I will upload an actual photo as soon as the print is finished
Based on the very good model of ER605 & OC200 Rack Adapters (V2) by Sorcier, I remodelled them to fit 2x TL-SG2210P. It's a heavy device, and 2 of them in this pair of brackets are recommended to be supported, either by support angles or…
SG22 Carry Handle with picatinny rail and fixed sights. 8.36 inches long, ideal for smaller printers. Open handle is easy to grip. Mount with 2 M4 screws and nuts, or similar in SAE
Barrel nut and 4.33 inch handguard for the SG-22. The nut uses heat set inserts for a more secure assembly. The nut has 4 holes every 90 degrees. Use a soldering iron to press in threaded inserts. There are two versions of the nut…
Modeled in Fusion. Designed to be printed face down. Only difference between left and right files is the text, you can just print two of the same side and it will work so long as you don't mind the text being upside down on one. I didn't…
SG22 6 inch handguard with lower picatinny rail for use with grips or bipods.
Vertical wall mount for TP-Link SG2008P switch.
6 inch handguard for SG22 with integrated foregrip.
A 10” rackmount for the TP-Link Omada SG2008P switch. The switch sits firmly in the frame so that no additional mounting hardware is required apart from the cage nuts. Be careful when removing the printing support as the rear braces can…
As far as I know is this model compatible with the SG2210XMP-M2 and ER7212PC.
SG22 Carry Handle with RMR Mount and integrated fixed sights. Designed to work with the 7 & ¼ inch handguard . This is a long part. It will not print on smaller machines like an Ender 3.
Print standing on the base - no supports required
I couldn't find a 10" rack mount for a SG2210P which was designed for the ports facing forward. This model has a gate at the back (press in using the bar closest to the "teeth") to stop the switch sliding rearward when you plug in network…
The replacement bottom cover that ensures the integrity of the case as a whole. Compatible with the AXAGON EEM2-SG2 AXAGON EEM2-SBC.
Small switches are convenient to be mounted under the desk, but not all have reliable mount holes. More over, Cisco ones have vents of the box, so we don't want to cover them. PLA works just well, if you are afraid of the temperature, use…
Model adjusted so the switch can be mounted and secured either way, leds front or cables front.
Holes are intentionally left small for a tight fit. print in the obvious orientation.
Wall Mount for a Meross MSG200 Garagen Door Opener Category: Household
This chock was designed as an ASG29 hangar chock but would be suitable for anything with a small ~250mm/ 10 inch wheel. It is designed to be a pair with a cord between them for easy handling. The face of the chock bends around the tyre…
2U 10" rackmount for TP-Link SG2008P swith and NanoPi R3s router with 20 keystone mounts.
SG2016 modular rack mount requires 1u rails, recommended to print with ASA https://www.printables.com/@LvL_Dani_470947/collections/2036642
Modeled in Fusion. Designed to be printed face down. I have two versions, first has the front slope down to the size of the device and second has a square front to better line up with the rest of the rack layers if you prefer. Only…
This is an SG22 6" extended handguard and barrel nut for airsoft.
New customer had 14 inch patchcabinet installed from Gigamedia the Sobox line ………. Since we couldn't find any parts parts like trays, the only switch we use that fit was the SG2210MP And the only some what proper solution was too make…
Inspired by @RussellDame_2238247's 10" rack mount. Designed with a tight fit in mind so that screws are not needed to keep it in place. The base plate extends far enough to be supported by L Brackets on the back of most 10" racks. I am…
It design not to be a tight fit (to prevent scratching), If you want more secure you can insert pieces of paper between shelve or use m3 screw on pre drill hole on top or below My print settings layer height: 0.2 wall: 3 infill: 15% If…
I couldn't find a 10" rack mount for a SG2210P which was designed for the ports facing forward. This model has a gate at the back (press in using the bar closest to the "teeth") to stop the switch sliding rearward when you plug in network…
Model adjusted so the switch can be mounted and secured either way, leds front or cables front.
I bought the SSG24 and was a bit disappointed that I could not attach my favorite scope because the cutout was a bit too big for the fixations. I made this rail to go on top of the original rail, so you get to use the full length of the…
