544 models
Update 25/08/2023 v1.2 added - access for heat break setscrew created, small amount of material added on the fan-side of the grille near the bottom to ensure proper clearance to heatsink fan. Update 11/04/2023 v1.1 added - probe bracket…
Print approx. €0.08–€0.10 excl. taxPreliminary estimate for one variant
English The idea was to create a tunnel portal similar to the detailed Noch Profi Tunnel. It is designed and scaled to nicely fit two tracks in H0 scale. I recommend to print it horizontally (obviously) and use only one or two bottom…
Print approx. €5.48–€6.70 excl. taxPreliminary estimate for one variant
Dollhouse vacuum cleaner model that imitates the most popular designs.
If you draw a circle on an x/y plot touching both axes, the distance from the origin to the centre of the circle is R+L, with L being the distance between the origin and the nearest point on the circle, and R is the radius. With a bit of…
Print approx. €0.81–€0.98 excl. taxPreliminary estimate for one variant
Caja para unas dos barajas de cartas de magic the gathering o juegos similares. Altura de capa: 0.2 (0.3 o 0.4 si tienes otra boquilla) Relleno: 10% Soporte: No es necesario(aumenta el tiempo considerablemente) Base: No…
Print approx. €12.37–€15.12 excl. taxPreliminary estimate for one variant
About Remix of Aneng Multimeter stand, added 2x2 gridfinity base with magnets and a box on the back to keep probes in it add magnets and it will be even more stable added version with more ‘flat’ angle for better reading the screen,…
Print approx. €3.54–€4.33 excl. taxPreliminary estimate for PETGSource material: PET
I couldn't find a crayon or pencil extender for my kids' crayon scraps. The commercial ones were either too expensive or too difficult for kids to handle. So I designed one myself. Advantages : Easy and fast crayon change. Optimized for…
Print approx. €0.16–€0.20 excl. taxPreliminary estimate for one variant
This is a variation of https://www.printables.com/model/1202146-wall-mountable-housing-for-dht-22-sensor for smaller sensors without own housing. See attached pictures for assembling. Please remember to insert the cable into the housing…
Print approx. €0.18–€0.22 excl. taxPreliminary estimate for one variant
Caja para unas dos barajas de cartas de magic the gathering o juegos similares. Altura de capa: 0.2 (0.3 o 0.4 si tienes otra boquilla) Relleno: 10% Soporte: Si Base: No…
Print approx. €27.71–€33.87 excl. taxPreliminary estimate for one variant
Questa è la versione TORO V2 ufficiale (utilizzabile su lower receiver g&g e similari). Il pezzo rende la replica estremamente più maneggevole, leggera e più rapida nel cambio batteria. TORO è uno stock fisso con un vano interno (tubo…
Print approx. €1.13–€1.38 excl. taxPreliminary estimate for PETGSource material: PET
This is my design of a bread box grate, that offers a practical solution for round bread boxes, such as Wesco's "Breadboy". The grate elevates the bread from the base of the box, enhancing air circulation which in turn helps to prevent…
Print approx. €4.71–€5.76 excl. taxPreliminary estimate for PETGSource material: PET
I keep an inflator chuck near my bikes in my workshop so I can quickly top off the tire pressure before starting a ride. I used to tuck it behind a piece of Romex wire on the wall (LIKE A CAVE MAN) but now that I have an MK3S+ and I know…
Print approx. €1.27–€1.55 excl. taxPreliminary estimate for one variant
TORO è uno stock fisso con un vano interno (tubo base+ fondello) di dimensione 30,90mm di diametro e 152mm di profondità. Un vano batteria che può ospitare tranquillamente 11.1v a celle separate da 1200mAh. Potete montare tranquillamente…
Print approx. €0.77–€0.94 excl. taxPreliminary estimate for one variant
There is no convenient storage location in the Bolt EUV for the two separate charging adapters needed to use NACS level 2 and DC Fast Chargers, so this caddy fills the need. It uses plug holder sockets designed by Dorbiman in a block that…
Print approx. €8.43–€10.31 excl. taxPreliminary estimate for PETGSource material: PET
Print and Support-Settings: I used the 'balanced' profile, 3 perimeters and 10% gyroid infill with snug supports under the pegs.
Print approx. €1.38–€1.68 excl. taxPreliminary estimate for PETGSource material: PET
Tired of shaving dust or water droplets in your Bathroom? With this Shaver Holder it is a Thing of the Past ! Just prop it up to the throne it deserves, for getting you a smooth finish every day ! It catches water droplets after cleaning…
Print approx. €2.08–€2.54 excl. taxPreliminary estimate for one variant
Der Haken benötigt noch 4 mal M4×16 er Schrauben und muttern. Die Muttern am besten geführt mit einer schraube von hinten eindrehen um den sechskanteinsatz nicht zu beschädigen
Print approx. €3.20–€3.91 excl. taxPreliminary estimate for PETGSource material: PET
Here is a fun Easter related model. The two pieces screw together to form an egg. There are two versions of the inner piece, one with a hole in the center to hide money and one without. The mode is similar to the popular “impossible”…
Attention! If you have a Prusa XL, you'll want to check out my new loader that mounts to the frame and is always at the ready: Also, be sure to check out the remixes for some great optional parts! No XL? How about Core One INDX? About…
these Figures are made by Frogkillerpl. I really love them. the Figures are not the original from the boardgame but very similar. at the moment i try a little bit to find the correct size and print procedure, so i cut the figures und…
Requires small length of shock cord & Ranger Band (if shock cord collar isn't used). Shock cord collar requires (1) M3 nut & (1) M3-6 or M3-8 bolt.
I have made a garage for small cars! Especially made for Hot Wheels -sized cars, the garage is available in two sizes. The small one for most of the cars, and the tall one for taller cars! It can be stacked upwards, so it can be displayed…
This model makes use of Bambu Lab's Lamp Kit , but should accommodate any light source you have available to you If anything could ever make you wish you could shrink down and live in a small house, this certainly would! Light up your…
Caliper bracket for Ikea skadis or similar. The hooks have an end to end spacing of 84.40mm. If you want to place the hooks yourself I leave you the following addresses. Original model of the bracket:…
I have taken ALL of the work out of mounting your Logitech C270 to your Ender 3 V3 SE X-axis. You don't need to do ANYTHING other than have this camera (or camera with similar mount), and this Ender, then just print. No hardware? No…
English version below Hardware für ein DIY steel darts scoring system (z.B. ähnlich autodarts, wedart, dartit) Check out my new foldable design…
I think the Sharrow MX-1 is pretty cool looking and if it lives up to the hype perhaps a new standard in marine propellers. Print Settings Printer Brand: Creality Rafts: No Supports: Doesn't Matter Category: Hobby
Description : Sovol dryer is perfect but the underside gets very hot. This holder protect the support and help to dissipate heat. re-use original pads hold in place without glue Version : V1 (deprecated): - Perfect for my dryer V2 : - Add…
Mount (clip) for Shure SM58 and other compatible microphones. With 3/8-16" mount (for standard microphone stand) and 1/4-20" mount (for photo stands/tripods). Can be used with original screw and nut as well as any part can be used instead…
All designed parts of the peristaltic pump are printed out of PETG. For the hose I have choosen silicon to avoid high forces by rotating the impeller. The hexagon shaft where the impeller is put-on have two interfaces, on one side an…
If you like this model, please throw me a like. Designing the models is time, filament and coffee consuming. If you want to support my work bye me a coffee. Thanks! Check out my other models. Description: I like the idea of Jerryie's…
This portable drill press is designed for Makita DHP480 18V Cordless Drill . The drill is attached to the drill press sled from the conical torque setting ring, as shown in pictures. The torque setting ring in this particular drill model…
I've been having fun using Shred-er mags with the Vigilante, but in my shop I'm frequently hunting insects larger than flies. A little more ‘oomph’ would be fun. Current versions: The V10 barrel and V8 cylinder are quite functional, well…
Electric screwdriver holder Parkside PAS 4 C4 for Ikea skadis or similar. Two models. One where the charging usb is on the right and the other in front. The hooks for Ikea skadis or similar have a separation of 44.8mm from one end to the…
DD-SM Mount I created this mount to have the motor and extruder as close as possible to the X gantry bracket to not have the weight of the motor hanging a long way away from the metal bracket. This mount is very rigid, there is no droop…
In order to cool my SB2040 canbus-board (with extruder-driver onboard) I used to have a 30mm fan cover sitting on my Clockwork2 extruder. Now switching to Galileo2, noone seems to have designed such cover, only for smaller 25mm fans…
Caliper bracket for Ikea skadis or similar. The hooks have an end to end spacing of 84.40mm. If you want to place the hooks yourself I leave you the following addresses. Original model of the bracket:…
I needed a replacement cover for a TI-89 Titanium edition that I was selling on Facebook marketplace, so that the buyer would be satisfied. Luckily, I had another TI-84 calculator that still had its original cover so I could recreate one…
This is a low profile ceiling rose for pendant lamps similar to the one included in the IKEA HEMMA cord set. I like the practical design and cheap price of the Hemma ceiling light suspension, but the ceiling rose is far too big and bulky…
Here is a set of Shelves and Holders for your glue sticks or any similar size tools/items. Made specially for HSW or Honeycomb Storage wall with Hex wall fixings. Depending on Your printer it is possible that a very little sanding will be…
Remixed from dual version: https://www.thingiverse.com/thing:4273415 IG post: https://www.instagram.com/p/CHvzaRlB7cl/
I use a lot of Bosch Professional hand machines in my workshop and have a matching FSN 1100 guide rail. Unfortunately, my beloved Makita RT0700CX2J router does not fit this rail. Buying a Makita rail and a matching adapter is out of the…
Update 3: The v3 “Slim” files. Final new version for now is a pair of new files, the “slim” brackets. I trimmed some material off that may not have been necessary, speeding printing and saving material. I thickened the bases to ½" for…
A Mellophone or Trumpet mouthpiece holder for buzzing with the horn in hand. All functioning iterations of solidworks part files and stl files are included. Their features are summarized below. MK II no resistance hole and slot for m3…
The wall mount is designed to keep the router securely in place, in my case in a camper van. Compared to the model I remixed this from, this mount uses much less material therefore prints much faster and is designed as a snap-on: a tab…
This is an scaled security fence, similar to the one used by police as crowd control barrier. My son uses it with him hundreds of Playmobil figures, simulating concerts and other crowded situations. You must print one fence with two fence…
A gantry plate for 3 roller wheels that fits on a 40mm wide v-slot aluminum extrusion. For a full assembly you need: 3 roller wheels with 24mm diameter 1 eccentric nut ID 5mm that fits in a 7mm hole 2 spacers ID 5mm 3 fasteners M5x28 or…
Like many others, I store my filament spools in IKEA Samla boxes. This container is designed to be attached to the lid of such a box using strong double-sided sticky tape. It holds approximately 180g of silica gel. You can close it with…
Simple painting Handle. Ergonomic. To use with patafix/Bluetac. Update: -29/12/2022: New model Added
As seen in my workspace redesign video above… Simple two piece wedge style speaker stand design. Trim piece snaps into the wedge and you can add some glue to be sure it doesn't move. Edifier R1280 are great budget friendly near field…
I was looking for a good build plate holder I could screw onto the side of the enclosure my printer is in. I didn't find any so I remixed the best free standing one I found to add a back plate with some countersunk screw holes so that it…
Are you in need of a way to store your Vallejo paint or paint from other companies using the same D25mm bottle? This might be a solution. Originally inspired by one of the videos over at Tested where Adam savage builds a set of Model…
German: Anschlagpuffer Heckklappe für z.b Opel Vectra C Teilenummern: Opel-Nummer: 0176731 GM-Nummer:24427457 English: Bumber tailgate for example Opel Vectra C Part Numbers: Opel-Nr: 0176731 GM-Nr:24427457 Note: This is not a original…
I have an old Herter's reloading tray that I prefer over many of the current commercial product designs . This design is an homage to that Herter's tray which held 60 cases, this design holds 50. Opening is 0.55", in the picture you can…
Print at 0.15mm layer height. Models should be in correct orientation for printing. Tolerance at mounting point is 0.10mm on either side which makes for a snug fit. If your printer isn't very good at dimensional accuracy, you may need to…
Simple gun stand for Dan Wesson or similar revolver. Ammo stand is only ok for 4.5mm CO2 ASG ammo of this gun, and the SAS star. Print instructions No raft, no supports, designed to be printed in 0.20mm and with 10-15% infill.
This is an addition to the existing hook bottom, for pens, pencils or similar. The holder fits exactly between two hook bottoms. He has a holder left and right. The hole has a diameter of 10 mm, so you can put anything of that size in it.…
created a little landing pad for my DJI mavic mini drone. Printed the “H” at first and after that immeadiatly the body upside down without moving the printers bed have fun with it
Parts required : Slim 23/20 mm thick stepper motor BMG extruder /clone E3D V6 hotend/clone 30x10 mm blower fan 24v recommend M3x8mm bolts x 5 M3x16mm blots x2 M3x20mm bolts+nuts x2 M3 brass inserts x6 5x3 mm neodymium magnets…
Ya que mi furgoneta solo tiene un soporte de latas pues hice este para tener cenicero y lata al lado. Se imprime sin soportes. si se quiere poner en el lado derecho habria que hacerlo en espejo. Necesarios 4 tornillos
designed an adapter to use the cricut joy infusible ink pens, i bought by mistake, in my cricut explore air2. Print instructions print it without supports
CNC hold down is similar to V-Carve. Three sizes. I printed this upside down and they turned out great. I don't have a pic left I them at the shop. (Slightly wider than original clamps from V-carve. Maybe 1 mm wider.)
I came across this on Tinkercad, but it contained quite a few errors in the model, misaligned bits etc. So I cleaned it up and made it more printable and now it lays flat on the print bed, the slats are properly meshed with the crate body…
This model makes use of Bambu Lab's Lamp Kit , but should accommodate any light source you have available to you It's a friggin' LIGHTHOUSE! PRINT IT FOR YOUR OWN SANITY! This cute lighthouse was designed after the same style that my Cozy…
You are doing me a big favor by clicking the Like button :-) Samsung TV holder for on the wall or similar. Use double-sided tape.
For a total saving of a whopping… 36 grams. At least it's a quick project! And a 78% weight reduction for these pieces alone is alright. These will all add up in reducing ghosting at high speed printing. I've never had issues with my…
This is a cnc dust shoe made for 65mm spindles. Has enough clearance to press the spindle lock on both makita and katsu routers. The brush side is held by twelve 5x2mm magnets to facilitate tool change. Mind the magnets polarity upon…
This adapter enables the use of a car/bicycle pump to pump up an Air Seconds tent to the 7psi/0.5atm that is required. Can also be used for mattresses and other inflatable camping equipment. Be aware that a car/bicycle pump can easily pop…
I recreated the rim caps for a VW Golf 2 or similar with 60mm diameters. Printed in PETG so the latches do not break so easily. Final model has no text, but feel free to add! If you like my work and want to support it you can do it here:…
The Bill I present you with The Bill, The Hydroponic plant supporter. I made this for my wife's Gardyn Hydroponic Garden, it will also work in other brands too. Some of the smaller leggy plants needed extra support at the base. The Bill…
UPDATE 4/28/2019 So after some more time and much learning, I have made some minor tweaks for better results using different nozzle diameters. Now I have added two different heights for even layering with a given nozzle diameter. 111mm…
This is a mount for the FYSETC USB ADXL345. It mounts easily to most Ender 3's and its clones (I am personally using this on a Voxelab Aquila). It mounts easily and securely to the printer by sliding it firmly onto the X and Y Gantry.…
Dust guard for a 3018 pro. Drop the spindle down a few mm's and clamp this to the bottom of the spindle. Fits 44.5mm spindle (with some clearance for smaller / larger Fits 35mm hose for dust extraction Uses M3 nut and bolt Uses 10mmx2mm…
Flexible GoPro style camera mount printed in TPU for the 2 part version for OTK style Nassau Panels. I couldn't find any STL versions online for the OTK Nassau Panels and I needed one urgently for a race requirement. Single part version…
This mount is specifically designed to keep your 3D printer's nozzle clean automatically. Built for the Ender 3 S1 and similar models, the design includes a cleaner inspired by the Bambu Lab system, but adapted and enhanced to work…
StageTop Hexagonal (Hex) PlayTile for Battletech, Gloomhaven or other Game but with indented hexes. Remix from: https://www.printables.com/model/438818-stagetop-hexagonal-hex-playtile-for-battletech-glo
Sample video: My FB feed started to show me all sorts of bird feeders including some commercial options that had built in cameras. I decided I had to create my own version. It's all parametric so you can modify any of the sizes using…
One of the nozzles from my Parkside cordless air blower broke so I quickly modeled all three of them in CAD. The diameter is 28 mm so they should not only fit the Parkside tool but similar ones. You can of course scale the models up or…
Upgrade your cycling safety with the Velobuild VB 167 Seatpost Radar Mount designed for Garmin Varia or similar radar devices. Crafted for easy installation, it requires an two M2 heat set inserts and a M4 heat set insert and screws.…
Holder for squares and similar things for the honeycomb storage wall. It got two slots for two different things. For this model you dont need the insert just plug it straight into your Honeycomb storage wall. Link to a collection of my…
Building my painting and model working corner. After some research I didn't find any Paint Shelving/rack I liked so I decided to project my own. Result completely meets my needs and I really like it. So maybe I will be not the only one.…
These parts were designed for use on an iDoo 12 desktop hydroponic system, but should work with any systems using 30mm/1.18" holes. Algae Blockers (no more stickers) These reusable algae blockers replace the single-use stickers that are…
Holder for cordless orbit sander like Makita DBO180Z Print Settings Printer: Artillery Sidewinder X2 Rafts: No Supports: No Resolution: 0,2 Infill: 20 Filament: Extrudr PLA NX2 turqoise Category: Other
This is based on the Dremel Attachment for Sanding & Grinding. Drawn from scratch using Sketchup. Inner ring is from this thingi - http://www.thingiverse.com/thing:678471 - It was not manifold so fixed it using this free service from…
A key for opening 200l plastic drums. These plastic drums are easy to acquire, and are useful for many things. This key makes them easy to open.
In order to use both hands with the Parkside-Lidl PFBS 12 pen drill, I designed this simple two-piece holder that is easy to apply and remove. The decision to keep the device blocked mainly by friction in the rear support stems from the…
These Servo-frames are perfect for the KST X10 or similar Servos in same size. Best filament-choice is PET. 100% infill, print time for 2 frames is about 52 minutes.
Introducing this ToDo list stand that is perfect for keeping track of your daily tasks. Inspired by the Ugmonk Analog stand, this stand is designed to help you focus on your most important work. The stand is suitable for A6 paper cards…
This was designed for the Monarch Takedown Recurve Bow, but if your bow has an attachment point with holes spaced 34 mm apart, it should also work just fine. You will need (2) #10-24 x 1/2in screws/bolts. IMPORTANT: Printing the part in…
For MJX Hyper Go H16H H16E H16P 16207 16208 16209 16210 rc car. Part Numbers: Front swing up 16210 Front swing down 16220 Rear swing up 16240 Rear swing down 16250 Most of the measurements are the same, a bit redesigned to be more beefy,…
This is designed to work with the ZK-4KX , but will likely work with many similar products like the ZK-SMC01 Stepper Driver with a few mods. ZK-4KX Buck Boost Converter Panel/Lid 2x2x5 Gridfinity Container with ventilation Hexagons are…
Support with and without hooks for the Wowstick S1 electric screwdriver. This is a remix of the user obuslive. https://www.thingiverse.com/obuslive/designs -The size and use of filament for printing has been reduced. -It has been added…
Snap-in vented cover for 5.25inch drive bays with vent fins to match the design of the HP Z-series workstations. Print with black PETG. // Print with inside surface to the printer bed. // Use tree support. // Turn on ironing. // Consider…
Description Added an adapter for Bambulab A1 silicone nozzle wiper made to install on the bracket. It uses standard Bambulab A1 silicone wiper. Simply print this variant, screw it on the mounting bracket and use the adhesive side of the…
Es un soporte para el mando a distacia de la tv, pero cualquier mando con dimensiones Ancho X=50 / profundo Y=27. Tiene opcion para anclaje con tornillos o cinta adhesiva de doble cara. Category: Organization
This design snaps onto the spool to give it support. I printed with PETG, no support required. Printed on an Ender 5 Plus.
Note: For the X-Max (X-Plus), the same reduction of lead screw induced wobble can be accomplished by removing the bearing at the top of the lead screw And using the stock couples. This applies for 75% of the max print height. For prints…
One day my wife decided to learn how to make bows out of fabric ribbons. After watching YouTube she needed a Bowdabra. 2 hours later I was printing my own version of it. Printing No supports needed Print in orientations shown in the…
Should be a replacement for drive caddies with model numbers: F238F/0F238F, G302, X968D, KG1CH. Should fit Dell server models: Dell PowerEdge R720 Dell PowerEdge R710 Dell PowerEdge R520 Dell PowerEdge R510 Dell PowerEdge R420 Dell…
