24 models
A simple clip to pass antenna wire through and to be held by a carbon 6 pole or pretty much any fishing pole with a decent enough top section (i.e. not the very fine squid pole types). The simple version should be adequate for most…
Support rings for telescopic HAM radio masts in various dimensions. These can easily be scaled in your slicer to fit other sizes, mine are for a SOTAbeams ultralight mast. Re-designed in 2020 to provide more strength at higher winds.…
Lightweight set for portable antenna setup only 22gr for all elements in TPU Set was designed to be as light as possible, with decent ammount of strenght, and for minimum ammount of guying rope to be used. Designe is intended and printed…
This tip is designed to press fit on top of the SotaBeams Tactical Mini Antenna Mast. It is designed to accept a plastic carabiner - the kind recommended by KI6NAZ for example. It has reinforcements on the ring for better stability. It is…
This is a compact printable case for the SOTAbeams PP 4-Way kit, which is a small and economical distribution block for DC power up to 25A using Anderson PowerPoles. These kits make a great addition to a go-box to power your radio and a…
Wire support for vertical (or any other wire) antenna using Sotabeams Carbon 6 portable mast. Designed for 2.5mm diameter wire. Slides over 2nd from top section with tight fit, no aditional hardware needed. Holes are very similar in…
Guying ring for Carbon 6 mast. Attaching height about 2m from bottom. Designed to “catch” junction point of both 7 and 8th section from bottom, so it uses reinforced sections. Rope holes 4.5mm. Tight fit around sections, depending on your…
This is a replacement threaded cap for a SotaBeams Tactical Mini. Mine broke so a created this to replace it. I printed in ASA to withstand the Texas summer heat and with 0.1 layer height for thread resolution.
This is a low mass guy ring for the SotaBeams Tactical Mini Antenna Mast. This is sized for the 4th segment up, which seems to work well. It's almost chest height. PETG might be warranted for windier/higher stress climates. The fitment…
This a ring to attach guy lines too for supporting a SotaBeams Tactical Mini.
I designed and printed this as I damaged my screw cap for the sotabeams tactical mini mast. I printed these in PLA Typically used for SOTA / Summits son the air. V4 / version4 is a better fit. There are TWO versions of the tactical mini…
Sotabeams Tactical Mini Antenna mast guy rings. Can be used for both top and bottom. Uses two M3*20 bolts and parachord for guying. Printed in PETG with 4 walls, 25% infill.
This is a UHF/VHF dipole center mount that will deploy on a SotaBeams mast.
This connector is made for hoisting a matching unit to the top of a Tactical 7000 mast. It is modeled after https://www.sotabeams.co.uk/versatile-top-antenna-insulators-5-pack/
Ich habe den Halter für einen SOTABEAMS Carbon 6 entworfen. Der Innendurchmesser beträgt 3mm. Zum Drucken eignen sich PLA, PETG und natürlich auch andere Filamente in den Standardeinstellungen.
I designed these 3D printable glands in OpenSCAD to allow SOTABeams traps to be easily waterproofed using standard glue-lined heatshrink. SOTABeams recommend liquid electrical tape, but I find this a bit messy and using heat shrink tubing…
Remix of the Cap & Spike for the Sotabeams Tactical Mini 6m fibreglass mast. Cap: https://www.printables.com/model/109648-sotabeams-tactical-mini-threaded-cap Spike: https://www.printables.com/model/109603-carbon-6-ground-spike Just screw…
Quick and easy print for saving your SOTABEAMS travel mast from damage on the hard metal lip of the car mount sleeve. I printed out of PLA for testing then 90a TPU for a tighter fit and softer hold. This model was designed in onshape.…
A quick and easy wire antenna anchor for the SOTABEAMS travel mast. I designed this for holding a chameleon emcomm wire antenna up about 7 meters on the mast without the need for zipties, tape, or other random wire holders. I originally…
End cap replacements for both ends of the SOTABeams 10m travel mast. These are designed to be printed in TPU95, but they can probably also be printed in other strong flexibles. Solid materials such as PLA and PETG will not work. I printed…
I designed these to provide a padded end cap for the SOTAPOLE 10 - protecting the mast sections both in transport and in the event of unexpected collapse. Printing with 0.4mm nozzle, 3 walls and 10% infill should give a tight fit and a…
End cap replacements for both ends of the SOTABeams 10m travel mast. These are designed to be printed in TPU95, but they can probably also be printed in other strong flexibles. Solid materials such as PLA and PETG will not work. I printed…
A printable case for the SOTABeams Power Conditioner Kit This kit converts 7-20 VDC into very clean 5.1 VDC (@200 mA) for use in powering USB radio devices like the WSPRLite. Additionally required for assembly: 6x M2x4 screws 6x M2x12…
Der Erdspieß verhindert, dass der Antennenmast am Fuss verrutschen kann. Der Innendurchmesser beträgt 31mm. Zusätzlich wird folgendes benötigt: 1 x Schloßschraube 6mm (in beliebiger Länge mit durchgehenden Gewinde) 1 x Mutter 6mm 1 x…
