Search results: teds

Sort order

17 models

P
PrintablesGuldok

PrintedSolid Door Latch

simple door latch that requires a 5mm countersunk screw and a 5mm nut that is embedded.

Print approx. €0.75–€0.92 excl. taxPreliminary estimate for one variant

Downloads
29
Likes
4
Rating
0
P
PrintablesPeter Farell

Bill and Teds Phone Booth Time Machine

Bill and Teds Phone Booth Time Machine. Attention!! the gcode is for a .6 nozzle at .3mm layers. If you want to use a .4 nozzle you will have to load the .3mf file into your slicer and slice for that nozzle at .15 or .2 Im not sure if the…

Downloads
288
Likes
72
Rating
0
P
Printablessaabotage900

Easy Print PrintedSolid Enclosure Magnetic Latch

A simple latch for the PrintedSolid Prusa next gen safety enclosure. This is a super easy print, with no supports needed, no glue, and just press-fit components. It just needs 2 neodymium magnets, 2mm thick and 10mm in diameter, available…

Downloads
112
Likes
14
Rating
5
P
Printablesbykim

PrintedSolid Jessie Cardboard Filament Spool Filler Spacer Support New Version

Yet another spool design, yet another spool support design. Thankfully, the new cardboard design allows for a minimal spool support. This one costs less than 16g (~8g each) of filament per spool. Printed with a 0.6mm nozzle at draft layer…

Downloads
106
Likes
11
Rating
5
P
PrintablesPaul C

PrintedSolid Jessie Cardboard Filament Spool Filler Spacer/Bushing Support

Jessie went to cardboard spools, either to save money or the planet or both, but the cardboard spools don't unwind that well and really need a bushing, so this is what this is. This may be overkill, but they stay on and work well.

Downloads
63
Likes
8
Rating
0
P
Printablesbykim

PrintedSolid Jessie Cardboard Filament Spool Filler Spacer Support

PrintedSolid Jessie Cardboard Filament Spool Spacer support. Allows the spool to rest more evenly on the spool holder. EDIT: updated design files with chamfered edges and a very slight increase to diameter to create a more snug fit NOTE:…

Downloads
49
Likes
5
Rating
5
P

PrintedSolid Jessie Spacer Ring RepWinder

This is an adaptor ring for the PrintedSolid Jessie PLA rolls to work with the RepWinder from Repkord. The Generic ring was just a bit too tall to work, so I shortened it up. Use the generic prusament base cap with this spacer and the…

Downloads
39
Likes
4
Rating
0
P
Printablesbykim

PrintedSolid Jessie Filament Spool Support Filler

This is remix that increases the outer diameter of the original design to accommodate changes in the Jessie spool design. Done in TinkerCAD. When the weight of the spool is supported by only half of the inner spool support, it tends to…

Downloads
34
Likes
1
Rating
0
P

PrintedSolid Jessie Cardboard Adapter RepWinder

Another adapter for the printed solid Jessie spools now that they are moving to cardboard spools. I didnt want to miss out on using my repwinder for the most common spools I used, so I did a ton of remixing to make this work. You…

Downloads
28
Likes
7
Rating
5

PrintedSoild Enclosure Pi mount and vent tubes

Pi enclosure vent and pi mount. the hole for the vent is made for a 60mm fan spacing. Check out my Printed Solid door handle too!

Downloads
18
Likes
3
Rating
0
P
PrintablesEnrique182

PrintedSolid Prusa Enclosure Filament Guide

Same as Krisas Man's V8, but fitted to work with my Filament Passthrough https://www.printables.com/model/441260

Downloads
17
Likes
3
Rating
0
P
PrintablesLanky

Phil and Teds 10 inch stroller front wheel

This is a replacement 10" wheel for Phil and Teds baby strollers. You can remove the old tyre with brute-force and the new wheel bolts together in two pieces. You can re-use the old bearings and axle. 12 M3x45mm countersunk screws and…

Downloads
15
Likes
3
Rating
0
P
PrintablesOldCoder

Hatches for PrintedSolid Prusa i3 box V2

Updated large hatch to hold power supply (PS) with shelf to hold PS, bolt on ‘strap’ to secure PS, and slot for wires to pass. Updated all hatches to have recesses for hex nuts, so that you can just insert screws into hatch from inside…

Downloads
14
Likes
2
Rating
0
P
PrintablesSGA

PrintedSolid enclosure door latch

I downloaded and printed several of the latches on Printables and Thingiverse for the PrintedSolid enclosures, and none quite fit my needs. So, I made one to suit. These are oriented as I suggest printing. I use supports for the one with…

Downloads
14
Likes
3
Rating
0
P
PrintablesSGA

PrintedSolid Pulse enclosure spool mount

I was tired of the perch spool mount on my Pulse XE that would not let the PrintedSolid enclosure door close fully. I was inspired but the remaining spool arm left after I assembled my Original Prusa Enclosure, so I made this.…

Downloads
13
Likes
1
Rating
0
P
PrintablesAtomicBleach

Phil & Teds Parade Child Carrier Foot Frame Fix

Recommend printing with a strong profile like 4walls and 30+% infill. Also would print with a strong material like cf nylon or pet-cf.

Downloads
8
Likes
0
Rating
0
P
Printablesdexmexter11

from bill and teds exelent adventure

cool bill and tedsssssssss

Downloads
7
Likes
4
Rating
0