Counting matching models…
Probably the best knobs for tektronix oscilloscopes. In this case, mine is the tds 210, but there are many compatible ones. There are already many models, but I didn't like any of them. They all had a big defect, they don't fit together.…
Feet and rubber pad inserts, universal across the Tektronix TDS500/600/700 oscilloscope family and possibly other Tek equipment from related lines. This is a near-identical copy of the original with a few changes to take FDM printing into…
Printed in standard PLA with low layer height (0.8mm height took 1 hour) and 55% infill. Tight fit. Print two so they match!
A set of 3D models of knobs and buttons for the Tektronix TDS210 oscilloscope . Also may be suitable for other Tektronix oscilloscope models. The set includes: Tektronix knob mini – small knob; Tektronix knob – large knob; Tektronix…
The knobs broke on my old Tek oscope so I made a replacement. This model is as close as I could get to the original design in look and feel. I wanted to make sure it fits snuggly so it doesn't fall off in use but can still be removed.…
I bought my Tektronix 50 MHz scope used a few years back. It came missing the control knob for trigger level. I would frequently swap the "holdoff" knob, located directly below it, until one day, one of the two prongs seating the knob…
Knob for older tektronix 7000 series and possibly other scopes. It requires the original metal insert. To apply the aluminium insert, remove the screw, heat the insert up with a soldering iron and push it inside like a standard heat…
Hello, this is a front cover designed for the Tektronix 465 but probably fits the 465B (but not the M) or other Tektronix scopes. It fits well and won't fall off because of the clips holding it in place. Print it with at least 2-3 walls…
This is a replica of Tektronix part number 214-1593-02 which is no longer available. This barrier key snaps onto the EDAC card edge connector that is used in TM500 series power supplies. It prevents incompatible plugins from being…
If you like my design you can support me on BuyMeACoffee - https://www.buymeacoffee.com/kaushikbm -------- Tilt feet for Tektronix scope. Designed using FreeCAD. Print Settings Printer: FDM printer Rafts: Doesn't Matter Supports: Doesn't…
Tektronix 2230 oscilloscope front cover Snap on front cover for Tektronix 2230 oscilloscope. Printed in two halves plus clips and connector for glue. Based on an ebay listing for an authentic front cover, this should fit models: 2213,…
It's a very simple but useful accessory. It fits well to my Tektronix 2213A oscilloscope, but I think it will also fit into other similar models.
Replacement plastic plate for the standard test fixture on a Tektronix 576 Curve Tracer. I believe it will fit the 577 as well. Does not include the provisions for the HV interlock (I don't have the plastic cover, like most people mine is…
This is a front protection cover for my Tektronix (Tek) 454 oscilloscope. It has hooks at the left and right side which clip on the side of the scope to secure the cover. I quickly threw this together and printed a few tests for fitting.…
This is the first file I have ever shared. Just replacement feet for a tektronix model 468 oscilloscope manufactured from 1980 to 1985. I increased layers and added fill to add strength. I hope someone finds this useful. Any tips from…
UPDATE 2017-07-04: New Model with improved strength. The kickstand that came with my Tektronix DMM914 Softcase broke, so I made a preplacement. It's been working perfectly for 5+ years. Model comes with support building as I had troubles…
The one from 2024 by Uski was too big for my 210, so this is a modified version. It took a few tries to get it right, and since the size of the printed power button hole can vary depending on your printer, I’ve included 4 versions with…
This model provides replacement front parts for TEKTRONIX 7000-Series Plug-In Extender tray (067-0589-00 Calibration Fixture). These plastic components are prone to breaking over time due to material aging, making these replacement parts…
The end piece of the the flex shaft coupler for Tektronix oscilloscopes.
Laser-cut insulator panel and 3d printed brackets for TM501 power supply based on the existing design by NFM.
Replacement knob for a broken tektronix P6021 current probe.
Replacement cup / mounting ring for the Offset Mult pot on Tektronix 576 curve tracers. flip it over and print with supports on build plate
If you find my work useful you can: paypal.me: https://www.paypal.com/paypalme/printyourfix Visit my website for contact form: https://printyourfix.com/ Follow me on Instagram: https://www.instagram.com/printyourfix/ Visit YT channel:…
The feet modules of the Tektronix TDS3000-series tend to crack and break after decades of use. This can lead to the oscilloscope being unstable, or you may not being able to use the feet at all. This model is a foot module which replaces…
Hook to allow Tek P6131 & P6139A (not B) probe cables to be coiled out of the way when not in use & hung on probe body.
NOTE : V2 files have slightly larger holes at the top, matching more with an original part. These items often break when an unfortunate or tragic accident has been experienced by a 7000 series plugin module. I used this to replace one…
skinny holder for a tektronix plug (AM503 current amp is what I use it with, but any TM500 module ( http://www.barrytech.com/tektronix/tektm500/tektm500.html ) should work. I don't have the tektronix power supply where this TM500 plugs go…
The Tektronix TM500 is a modular test equipment system offering a variety of plug-in modules that fit a dedicated series of mainframes with one to six module slots. This is a blank panel cover for one of its 6 open bays. The inset on the…
Tektronix O-Scope Alternate Sweep Circuit Board Clip #51 for the 2215A.
Adapter sleeve made to create a replacement ground lead for an Obsolete Tektronix P850 probe. Designed to fit the female socket connector end of a Tektronix part number 196-3113-02 which is being repurposed for the ground lead: cut the…
Have a Tektronix TAS 220? Have those long knobs for "Variable" and "Sweep Variable" broken for you, too? Good news: now you can just print a new one, and your semi-vintage oscilloscope can live on for a few more years! There are two knobs…
Replacement bottom feet for Tektronix 453/453A
A remix to fit Tektronix TPP0101 probes
This part replaces the failure-prone plug-in latch used in Tektronix 7000 Series modules, original part number 105-0075-00. The latch sits beneath the pull-release mechanism and is responsible for positively locking the plug-in into the…
After buying a used CT-1 probe without his case I propose an equivalent to protect the precious probe. All pieces are maintained with super-glue apply with a toothpick. Using SLA is a must otherwise the “Insert” part cannot be printed…
This is a battery door/compartment on Tektronix devices like the THM550, THM560, THM565 as well as MAC Tools ET-2020 (a.k.a. THM571) and even the Tempo TelScout TS90. These can be brittle and are often quite fouled by leaking batteries.…
This is for use in the lab
This model is a replacement power button for Tektronix AFG3000 series function generators. The original button has some very thin plastic elements that can snap, resulting in the button dislocating from the power switch and rendering the…
Spare front panel knob for Tektronix 2225 oscilloscope. Used for trigger. Shoud be compatible with Holdoff, Intensity and with the different positioning knobs. It is a remix of…
You need 2 M2 bolts (skirted to be flush) and 2 M2 metal threaded inserts (see the picture). I printed these models on their sides using a Core ONE. This helps the appearance of the slider top. Note that you will need to set the slider…
I scored a used Tektronix TPS2012 oscilloscope of the TPS2000 series (two isolated channels, battery operated). And of course the battery compartment cover was missing, as it is with most used units of that series. So I designed a…
A box for the high voltage probe. The key feature is the cutaway at the bottom. These probes have cables coming out of both ends, which makes it not a good fit for a standard box. Updated design which has holsters for probes, oscilloscope…
Simple knob to replace a missing one on a Tektronix PS280 DC power supply. Fits on any 6mm diameter shaft. Used 100% infill and spiral first layer for aesthetics' sake. Recommend to print in a retro-colored PLA to match the look of…
— for english please scroll down -- Kunststoffteile für meine Batteriehalter-Leiterplatte für das kleine Tektronix-Oszilloskop 222, 222A, 222PS und 224. Je ein Exemplar notwendig. Details und Leiterplattendaten unter…
I scored a used Tektronix TPS2012 oscilloscope of the TPS2000 series (two isolated channels, battery operated). And of course the BNC-Cover, which protects from the high voltages that this scope is capable of working with, was missing. So…
This is a simple floppy mount for Tektronix TDS500/TDS600/TDS700 series scopes. It supports both the Panasonic JU-226A and the TEAC FD-05HF floppy drive. Note the main mount may not fit to units with a 4 channel or later revision…
A box for the high voltage probe. The key feature is the cutaway at the bottom. These probes have cables coming out of both ends, which makes it not a good fit for a standard box. Updated design which has holsters for probes, oscilloscope…
Probably the best knobs for tektronix oscilloscopes. In this case, mine is the tds 210, but there are many compatible ones. There are already many models, but I didn't like any of them. They all had a big defect, they don't fit together.…
