Counting matching models…
Build a motorized camera slider with Adafruit Feather and CircuitPython! Create HyperSmooth motion timelapse video with this build! Print instructions Learn Guide: https://learn.adafruit.com/circuitpython-motorized-camera-slider/ This…
My design is to add the words in white so you don't pull and attempt an empty mag. Yes, you should mage check prior to load. This way you unload your empty mad facing ‘Empty’ outwards to visibility.
Macropad with RP2040 and CircuitPython See HERE for a write-up on my website with pictures Most DIY macropads I could find on the internet were either too expensive or had too many features for my needs (knobs, displays, etc). My goals…
Learn Guide: https://learn.adafruit.com/circuitpython-octoprint-controller-and-monitor
POV LED Wand In this project we’ll show you how to build a POV LED wand. Adafruit DotStar’s deliver high speed PWM making them great for Persistence Of Vision. It’s powered by Adafruit’s Circuit Python, making it really easy to change and…
Modified model to have variables/parameters for slot count and slot spacing https://a360.co/3LTbemC
https://www.youtube.com/watch?v=QStYksk\_2ZM This is a DIY multimedia dial. It rotates like a knob and clicks like a mouse. It’s powered by Adafruit’s Circuit Python so you can quickly program it to run key commands in any application!…
The pico_test_synth pcb was originally designed to be held up by four M2.5 standoffs and screws, but I wanted a simple little case that was easy to snap on and off. This case has two tabs that will hold the qtpy_synth PCB well enough but…
https://youtu.be/46oyP1UV6fY These NeoPixels makes you wanna jump! Learn how to upgrade a cheap trampoline with interactive NeoPixel LEDs. Use Adafruits ItsyBitsy and a vibration sensor to make a trampoline light up when you jump on it.…
Super einfach und schnell zu drucken! Das raue Design muss im Slicer eingestellt werden! Schreib mir kurz eine Nachricht falls du nicht weißt wie das geht!
Each part has tabs that connect with M2.5 screws. learn guide: https://learn.adafruit.com/circuitpython-trombone-champ-control
Tastatur/Maus/GamePad-Emulator mit Raspberry Pi Pico und CircuitPython, Cherry-Switches, Jogdial-Mausrad, Synaptics-Touchpad und OLED alle Infos unter…
The qtpy_synth pcb was originally designed to be held up by four M2.5 standoffs and screws, but I wanted a simple little case that was easy to snap on and off. This case has two tabs that will hold the qtpy_synth PCB well enough but allow…
EN : Pyramid-shaped lamp for battery-powered tea lights. I recommend using transparent PVB as the material; spray it with propanol and let it dry. Do not use candles with an open flame. Here in 2 versions : a thicker one (V1), for which I…
really bad quick and dirty remix for MH-Z19 CO2 sensor and qtpy snap case. 9mm squares plus MH-Z19 cut out of top and tall-frame, roughly centered to allow for either pin end used Printed at high speed in eSUN PLA-LW (235c 40% flow) which…
I have been looking for a simple radio to build with a circuitpython board, and wanted a reason to use these great LED matrices from pimoroni . This uses their pico with battery support and has its own power button. You can recharge the…
Super einfach und schnell zu drucken! Das raue Design muss im Slicer eingestellt werden! Schreib mir kurz eine Nachricht falls du nicht weißt wie das geht!
There are M3 screw holes in the base and the model. There are also cutouts in the model to accomodate M3 nuts inside so that the base can be screwed into them. I used a strip of 7 NeoPixels, wrapped around and facing forward, they give a…
Already uploaded medals for 1st, 2nd, 3rd place, but this medal you can customize yourself by adding text in the slicer
