Counting matching models…
I designed and 3D print a dust cover located on the right side of the curricular saw that makes the dust extraction much more effective Starting from another similar project , I designed the same part but adapted to my TS55 REBQ version.…
This system prevents the TS55 saw leaving the guide rail FS when cutting with the sloped blade. Even with a 45 degree angle the saw remains secure on the rail thanks to the 2 stops screwed on the sole of the saw Inspired and adapted from…
This is a dust cover for the Festool TS55 FEQ track saw.
Replacement adapter to 36mm cleantec hose. It does not swivel, preventing the hose to get stuck on the rails. The side panel of the tracksaw needs to disassembled to install the new adapter.
Whenever you want to have your Twotrees laser engraver higher...
This jig is to help align the track to leave the exact amount of spacing for the kerf of the blade. This is used if the waste board is to the left of the track and what you need is on the right. Festool saws have different widths so use…
I was needing a part to connect a vacuum hose to my circular saw to extract wood chips and dust I designed the part in Fusion 360 with a female connector to enter the circular saw exits and an internal screw thread for the vacuum hose I…
This is a print in place model designed to print face up at 0.2mm, 15% infil using the designated supports. I've used PLA and ASA and both worked great. I designed this based on designs I tried from here that either fell out, rubbed on…
I modify the version also found owhich does not fit to my festool TS55 REBQ bought in 2019. The left side was correct , but the right side the 6mm hole was incorrect ( 1mm shift). I also improve a border, to be more easily removable, when…
I printed in PLA, any material is ok. Please note than I had to print a new board support in order to move usb cable on the right allowing to put the board on the left. This is needed to shorten the path as much as possible otherwise new…
This is an adapter for the Festool Plunge Cut Track Saw (TS 55). It uses the innovative CAMLOCK connector by @PeterH , along with the jcjames_13009 version of the Festool end connector . Related CAMLOCK Adapter: Festool Domino CAMLOCK…
TS55 cover: Remix gcode to reduce the amount of support needed.
a plain version without text, confirmed fits for the TS55 REBQ and TSC55 KEB.
You can use this CAMLOCK adapter to replace the vacuum port on your TS55 EBQ circular saw. Just remove the blade cover with the five screws remove the old curved one and put this in its place, put back the cover and the screws. Plug into…
Dust cover for the Festool TS55 EBQ track saw There is a version for hard plastik and also a version for TPU and other flexible materiel Both just snap in place Print settings PLA Layer Hight: 0.2 mm Infill: 20 % perimeters: 2 layers…
I needed to run a thin kerf blade (1.6mm) on a 2012 Festool TS55 REBQ and didn't want the 2mm thick riving knife placing pressure on the wood or forcing it apart before the end of the cut. I found a lock pin solution by tcatca (appreciate…
Printed with PLA strong. Use tree support for the positioning pin. I glued this tool with a small drop cyanoacrylate (1sec glue) on the original depth adjuster.
A simple adapter for the Festool Cleantec connector system, such as the one on the TS55 track saw to the Centec hose system.
For this build, you will need to print 5 main parts and 4 MFT Nuts. Parts: 3 Vertical arms (2 get assembled to make one long) 1 Arm / Brace 1 Base Plate interlocking part 8x M4 Inserts 8x M4 Bolts 10mm long 4x M5 Nuts and Bolts for MFT…
Beim Stationsbetrieb in einer Festool Basis um die Tauchsäge dauerhaft betätigt zu haben
Made slightly stronger as my first set broke after a few uses on the V point.
My locking mechanism for the TS55 at my CMS brocke and I needed a new one. Sadly the fitting one was not available anymore so I ordered another one which is slightly different (10002797). Because the screw layout doesnt fit exactly I made…
