Counting matching models…
I am not the creator for this model nor made any changes. Been looking for this for a while until i finally found it on unifi community website. original creator locked the comments and I could not ask his permission. Uploading here to…
Hier ist eine Ubiquiti Unifi G4 Halteplatte damit sich die Klingel besser an der Hauswand befestigen lässt. Bei uns war das Problem das sich hinter der Klingel noch andere löcher befanden die ein bisschen versteckt werden mussten.…
This is case for Waveshare Sony IMX179 8MPx camera which is 38x38mm. For back case use 3mm threaded inserts and use 10-13mm M3 screws. I printed without supports, but inner part is ugly then, so I recommend supports on.
Retoque el modelo porque la cámara tenía mucho movimiento una vez puesta y le faltaba más ventilación para que no se cal
Source: https://cad.onshape.com/documents/8e32626565cbbeef5e4cd8d3/w/b09365e8f3eeb6319f5a1b46/e/11d4dc9550a5c0cac525a516?renderMode=0&uiState=64aaf63abe953312f726ec55
Simple adaptor for tilting the camera 30° backwards, to allow a field of view closer to the ground beneath it. Remember to mount the adaptor before fastening the original mount to the adaptor, since the original mount will cover one of…
Fits to the left side gantry, ideally with a couple of magnets. Use short M3 screws to secure camera and adjust the angle. Remixed to fit the UVC camera module pictured. It supports hardware MJPG encoding.
This is a two part print . screw or double sided tape to wall. A E275-3-S UVC LED Chip on a board with a 3W LED driver to sanitize the toothbrushes inside prior to use.…
Top slot holds the magnetic mount for the UVC G3 Micro with a slot in the bottom to route its magnetic charging cable. Includes some simple cable management.
Door Hardware for Newell Acoustic MB72 UVC exposure cabinet Print instructions Prusament PETG
Your Nukit Lantern can snap into this 3D-printed box, enabling you to flush mount it any surface and protect it from tampering- or simply for a cleaner install. The box can be printed without support using PLA. The emitter's vents will…
These decorated plates snap to the front of your Nukit Lantern, enabling you to transform them into a number of fun, kid-friendly shapes. You can also decorate the plates with stickers and markers before snapping them onto your Nukit…
Why? I had to mount these cameras on a building that is insulated with Styrofoam (this probably has a more accurate translation) - one can't just drive a screw into that, instead a special “screw” needs to be used (I used a “Fischer FID…
The Nukit Lantern 222nm Far-UVC Light from @Nukit_2466521 is the least expensive independently verified Far-UVC lamp on the market, and comes with a handy mm-wave occupancy sensor to prolong the lamp's life by automatically turning the…
Eheim Halterung für mein 6mm Glas Technikbecken zum aufhängen hält sehr gut (PETG) 90%
Pokud chcete pouzít i pružinku, která drží víčko zavřené, použijte pro drážku kotouček 0,75mm do gravírovačky. Protože se vám drážku nepovede vyfrézovat úplně přesně, pružinka je pak v ní sevřená a nevypadne (viz. foto), což je plus.…
Frame components for Newell Acoustic Phoenix MB72 UVC cabinet Print instructions Prusament PETG
XLR dummy mic support base for Newell MB72 UVC exposure cabinet Print instructions Prusament PETG
The Nukit Torch 222nm Far-UVC Lights from @Nukit_2466521 are the least expensive independently verified Far-UVC battery operated lamps on the market. This model holds one of them at a nice angle in a vehicle's cup holder. I have provided…
Warning: UVC is the most dangerous kind of ultraviolet light. Do not expose your skin or eyes to UVC light for more than a few seconds at a time! For this build you will need the mini UVC fluorescent tube and power supply/ballast from Ali…
Warning: UVC is the most dangerous kind of ultraviolet light. Do not expose your skin or eyes to UVC light for more than a few seconds at a time! For this build you will need the mini UVC fluorescent tube and power supply/ballast from Ali…
A keychain holder / caddy for a UVC sterilization dongle. Should fit both USB-C and Lightning cable versions. Print this in a flexible filament. This is the product this fits:…
Policka k zasuvce kam se da polozit nebo povesit veci ktere se nabiji, telefon, sluchatka atd.
Avendo spazzolino con base e sterilizzatore UV separati, ho realizzato un organizer per avere più ordine sul mobile e una sola spina, così si riesce ad alimentare contemporaneamente i due dispositivi. Materiale usato PETG e ugello 0,4…
This simple model mounds a UVC industrial camera onto a 2020 aluminium extrusion at the back of your printer. The rack has a hole for you to put your wire through it. Required hardware: 1x UVC camera module…
Still have no idea what I'm doing but this one is a remix for the UVC-G6-Pro-360
Ich benötigte einen Referenzscan der Ubiquiti UniFi G3 Flex (UVC-G3-FLEX) für den Entwurf einer eigenen Halterung. Es handelt sich um einen groben Scan: Nicht alle Vertiefungen sind perfekt erfasst, und er wurde nur schnell in Blender…
This simple model mounds a UVC industrial camera onto a 2020 aluminium extrusion at the back of your printer. The rack has a hole for you to put your wire through it. Required hardware: 1x UVC camera module…
Bracket for holding a 8W UVC germicidal lamp fixture (see the photos to see what the lamp I purchased from eBay looks like.) The spring clips they supplied with the lamp were really flimsy, and kept coming loose inside my makeshift decon…
This is a Ubiquiti UVC G3 (pro) camera front removal wrench. I designed it for fitting the three grooves on the front of the camera. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 38…
I need portable UV Box on my car, to sterilized belongings like bags or groceries from supermarket (it's about pandemic things), so i bought mini USB wireless XIAOMI XIAODA UVC lamp for do the task. But i figure out that the lamp was so…
Unifi G4 Doorbell Pro Habe hier ein Halter für die G4 Doorbell Pro erstellt um die alten Schraublöcher zu verstecken. Am besten mit PETG/ABS/ASA drucken um die Haltbarkeit zu gewährleisten Viel Spaß damit
It's old, but it works. I have had several Unifi/Ubiquiti/UI devices, and surprisingly they still work, even when out dated. The problem was I lost the door that covers the bottom access door. I couldn't fine one online, so I made one.…
