26 models
Make sure your bridge settings are on point! Otherwise this will not result in a print good. I advice to print with a higher layer height than usually.
Print approx. €4.35–€5.32 excl. taxPreliminary estimate for one variant
Cheap webcam implementation to AD5M Flashforge sells camera kit, but it's kinda expensive in here, so i wanted to go to cheaper route. You need: (Maybe) Klippered AD5M - Haven't tested with the original firmware so it might work or it…
2 cases for the OV3660 3MP camera board/module with the small lens. Probably fits other board of the same form factor but I can't guarantee as I only have the ov3660. Minimal case is as small as possible and only includes a hole for the…
This is a simple mount for the OV3660 USB webcam on the Voron v0. The mount is designed to fit in the front left corner; you can mirror it if you want to place your camera on the right instead. Required hardware is: M2x6 screws and nuts…
a case for camera OV3660 and ender 3 s1 bed mount
Simple and functional two part housing for OV3660 type cameras. The housing front / main body comes in two variants. One with the arm mount on the side, one with the mount at the bottom. If you need the mount on the other side you can…
Extra long crevice tool I made for our Shark NV360, may fit other models or any vacuum hose with a ~39mm/1.54" ID. Collect random food particles from all the couch cushion crevices with ease. Print on the angled base, only support the…
There are already two available camera mounts on printables that fit OV3660, but I was not able to user either one of them https://www.printables.com/model/703993-voron-0-usb-camera-mount Great mount, but unfortnutely I bought a 110 fov…
Put together with m3 plastic nuts and 8mm m3 screws. Supports needed.
OV3660 camera mount for ikea lack enclosure
This mount is been used for mounting a OV3660 110° Rectangular camera module (https://www.amazon.it/gp/product/B088P1PKFM) to a panel of my homemade enclosure using four magnets (Two inside and two outside) to have it easy to remove. File…
OV3660 Camera Mount for Ender 3 Pro, remixed one part and combined to another model
A minimalistic mount OV3660 on an aluminum extrusion. I designed this to mount on Voron 2.4's Gantry so I made it as compact as possible as it's going to share space with multiple accessories. Use M4x20 screw Get camera casing parts from…
A simple mount for a OV3660 on the Voron Switchwire
ESP32-CAM Lens Adjusting Tools for OV3660 These tools are for breaking the lens factory glue seal and also adjusting the lens focus. The ESP32-CAM lens comes glued in place from the factory. I found it very hard to break the glue bond…
Yamaha YHT-399U HTR-5063 RX-V467 RX-V367 RX-V371 AV A/V Receiver Controller Holder
I find it easier to mount board on the other side of the axis that has X-axis motor – that gives more options for modding, so I designed holder for the PSU I have to be on the other side of the printer. Mirrored PSU cover for 24v 360W…
Print with ABS or ASA, no supports needed. Split camera holder to have separate top cover. Run your camera wire in an inner side slot of the front left profile. No disassembly, just push the cable under the tensioner. I use original…
i made this to mount the RES3TV360 for my home lab. needed 2x m3 bass insets and m3x8 screws (other sizes might work) 3x m4 bass insets and m4x8 screws (other sizes might work) i printed in PETG but any thing should work.
The bearing for the brush in our Shark NV365E vacuum cleaner started making a terrible noise due to the brush being fully clogged with hair (the tragedy of living with many daughters!). After taking things apart, the problem became clear…
As requested by a Reddit user. 0.185" holes, 0.125" thick.
Bosch Fridge KGV36640 handle KL831AS63 replacement.
Popup wall mount for the following ESP32 Camera - https://www.amazon.com/dp/B0H2TT5MRG?ref=ppx_yo2ov_dt_b_fed_asin_title Intended for use with ESPHome, setting up spot watcher cameras for use within Home Assistant. Screws or Magnet…
Detailed 3D printable Full Body V36 figurine, ready to print on FDM in PLA. Usage & Links Personal use: print freely. Commercial/digital redistribution is only allowed with a valid Patreon license: https://www.patreon.com/Marjers…
Print with ABS or ASA, no supports needed. Split camera holder to have separate top cover. Run your camera wire in an inner side slot of the front left profile. No disassembly, just push the cable under the tensioner. I use original…
2 cases for the OV3660 3MP camera board/module with the small lens. Probably fits other board of the same form factor but I can't guarantee as I only have the ov3660. Minimal case is as small as possible and only includes a hole for the…
