Counting matching models…
The VoronLightweightXCarriage by Vitalii3D 🥰 is a fantastic lightweight carriage for the Stealthburner but I was not happy with the existing cable management solution for a ClockWork 2 setup. So, time to make some parts. The Features A…
Vitalii CNC Aluminum Gantry Z-Chain/Endstop Mount/PG 12 gland
Please print from ABS or any other high temp material using official recommended Voron settings. A4T/XOL Mount
These parts are for Voron 2.4 Vitalii CNC AB Drive Units. Added Top Bearing Mounts for the AB Drive Units based on Hartk1213 Micron R1 Double Shear Mounts using F695 bearings and longer shaft steppers (OMC 17HS19-2504S-H 55mm). Changed…
Hello, I noticed while using my Chaotic Labs carbon fiber tubes, the x-end stop piece for Vitalii3D Super LightWeight Carriage came up short. I made a part that will now ensure that the end stop will hit the end of the carriage. Also…
Update 11/2025: Updated the brace so it does not interfere with the Cartographer connector. Also made a few more cable management cutouts for more routing options. I was having a hard time getting consistent results from my Carto/Beacon…
When you use the Vitalii3D XOL/A4T Mount for Voron Printers it's possible that your Beacon/Carto is hitting the hotend. In my case it was the Trianglelab Dragon Ace Volcano where Beacon hits the sock/heater block. The hotend is also in…
This is a remix of the X endstop holder of Vitalii3D-xyz's MetalTap . My Voron 2.4 Formbot kit included the X/Y endstop PCB that is mounted on the gantry. TAPs assembly assumes the X endstop to be on the toolhead itself. I wanted to keep…
I am using sensorless xy homing, so I wanted this improved/modified version without the endstop switch part.
Y-Endstop for Vitalii CNC Ganrty Included is a Blank, Voron logo, and Stealth Changer logo Install the CNC Gantry parts first. This endstop sticks out .5mm and will interfere with squaring up your gantry. The only extra needed parts are…
I bought this cnc x carriage https://www.etsy.com/listing/1639526932/super-lightweight-carriage-for-voron because the dragon uhf made my plastic x carriage heat sets fall out due to the plastic mount softening up from the heat. I also…
I was building my second Vitalii TAP and realized I didn't have any more of the correct opto sensors for it. But I did have a few left over from my purchase of 5 cheap ones a few years ago. So I modified his Wired Optical Sensor Mount.stl…
Redesigned extruder adapter (Sherpa Mini pattern), redesigned hotend mount (single piece vs two pieces), Beacon probe support. Stuff is being tested, BOM and guides will be added sometimes in the future.
PUG mount for the Vitalli Aluminum CNC Voron 2.4 A motor mount.
I created this updated PUG mount for the newer double shear variant of Vitalii3D's Trident AB mounts. I used the original design idea here and integrated a few variants of the popular PUG design. It should slide right into place with some…
PZ Probe Mount I printed with typical Voron print settings in ABS. I did use supports on the face adjacent to the stepper motor - that side is not visible. Mount to carriage with M3x6 BHCS, and mount board using screws supplied with the…
THIS MODEL IS A WORK IN PROGRESS This is designed to better mount an LDO Nitehawk NHK-36 cable (Described in the docs as "fully overmolded") to a Vitalii CNC EBB36 mount rigidly, including the spring steel umbilical guide. Personally I…
Mounts to Vitalii carraige for goliath-hextrudort-cpap-beacon combo.
Cable support for the Vitalii3D CNC EBB36 Mount, specifically for the EBB36 Gen 2 and Orbiter 2.5 configuration. I have designed it to be a very tight fit around the CNC Mount. Make sure the mount is pushed all the way into the plastic…
Uses 2 m5s, 3 m3s (one optional), and two m3 heated inserts. I've run this for 200 hours without issue. I use the secondary cable hole for a camera and the primary/PUG for my umbilical Model references the actual cnc design files from…
I like the vitalii3d XY joint, but the adapter for the end stop is out of date. I updated it to have a notch for the lip on the right joint as well as moving the holes to fit the hall effect endstop. I hope this helps others.
A cover for the Vitalii3D CNC Front Idlers that helps your Jabberwocky cutting arm compress fully to cut filament.
I have a trident, the Vitalii3D recommended mount makes the carto too far back and can hit the middle rear leadscrew. None of the other models I could find worked. So I created my own. y_offset: 22.5 I have two versions, one with just…
Printed mine in PCCF but I am sure ABS/ASA would be fine. After the first one melted from being too close to the hotend I just didn't want to risk it.
Modified version of the PCB Adapter for the VoronLightweightXCarriage
Bondtech INDX 1515 mount for Vitalii3D CNC Front Idlers.
This toolhead's MCU is a Fysetc H36 which uses the same mounting pattern as the EBB36 but has a preterminated cable that has no locking mechanism. I had problems with the cable coming loose and devised a quick, adjustable, easy to print…
Works perfectly for the ebb36 v1.2 + Orbiter and can also fit larger can cables such as 3do's. Also shortened the height of the original model and instead of the one-off heatsets for the main piece, you can use m3 nuts.
This is a remix with an adjustment to the lower mounting point to fit https://vitalii3d.com/products/xol-a4t-mount-for-voron-printers You still need the pug front clip from the original model. For me a M3x20 SHCS screw worked well for the…
Redesigned extruder adapter (Sherpa Mini pattern), redesigned hotend mount (single piece vs two pieces), Beacon probe support. Stuff is being tested, BOM and guides will be added sometimes in the future.
I created this updated PUG mount for the newer double shear variant of Vitalii3D's Trident AB mounts. I used the original design idea here and integrated a few variants of the popular PUG design. It should slide right into place with some…
When you use the Vitalii3D XOL/A4T Mount for Voron Printers it's possible that your Beacon/Carto is hitting the hotend. In my case it was the Trianglelab Dragon Ace Volcano where Beacon hits the sock/heater block. The hotend is also in…
This toolhead's MCU is a Fysetc H36 which uses the same mounting pattern as the EBB36 but has a preterminated cable that has no locking mechanism. I had problems with the cable coming loose and devised a quick, adjustable, easy to print…
I am using sensorless xy homing, so I wanted this improved/modified version without the endstop switch part.
Uses 2 m5s, 3 m3s (one optional), and two m3 heated inserts. I've run this for 200 hours without issue. I use the secondary cable hole for a camera and the primary/PUG for my umbilical Model references the actual cnc design files from…
Hello, I noticed while using my Chaotic Labs carbon fiber tubes, the x-end stop piece for Vitalii3D Super LightWeight Carriage came up short. I made a part that will now ensure that the end stop will hit the end of the carriage. Also…
Vitalii CNC Aluminum Gantry Z-Chain/Endstop Mount/PG 12 gland
This mount is held in place using the metal spacers that come with the Vitalii kit. The switch is held on with a M2x8 self tapping screw. also has a spot for a 2pin JST connector to make plugging in and unplugging the switch easier. Link…
