Counting matching models…
The blade length and hub measurements match the original, but I sort of eyeballed the angles of the fins. The hub fits snug, but should press on fine. I've been running this for a year in my shop and I can't tell a difference between the…
The fan only include blocks for windows up to 40", my windows are wider, so I needed additional blockers. Note the print orientation, there are small flats meant to interface with the bed. I recommend using a brim and supports (as shown)…
This is a switch for the VornadoAir 530 fan. You need support and slow print between 20- 40 mm/s.
BOM: M4 Socket head 20mm x 3 M4 Heat Inserts M5 Counter Sink 12 mm x 8 M5 Counter Sink 16 mm x 8 M5 Heat Inserts 10mm or 6mm x 8 M5 Bolt H:4.70mm x 8 Ball plunger 8x9mm x 1 (Ball Plunger Set) This design is for casements with these…
I printed with PETG at 0.15mm layer height. I used 100% infill and turned on “bobstro's supports," which are saved in the .3mf file. The tall end of the axle attaches to the large plastic gear with a screw. The other shorter end rests…
Wanted to mount the fan on our bedframe so made this model to facilitate that. The gap of which it rests on the frame is 3/4", so any frame similar to the one pictured and linked it should work as is. Fan:…
I kept losing the rubber feet at the bottom of my vornado and it kept sliding around and vibrating on counter so I modelled a replacement. Printed in TPU.
This is a replacement battery cover for a Vornado fan remote control. Remote says Model 184 on the back. It doesn't fit perfectly, but it works well enough. Fusion 360 files included if you want to adjust it for a better fit. Print…
I printed in PETG at 0.08 mm layer height, but I think it would work fine in PLA or other resins, too. The small layer height helps keep the threads smoother.
A simple wall mount to convert the Tornado Duo Compact Tower Circulator fan in to a wall fan.
These are replacment feet for Vornado fans. Vornado_foot.stl should be printed with tpu. My printer was having problems printing tpu so I made a mold for casting rubber feet. I mixed silicone with cornstarch and pressed it into the mold.…
Replaces the original knob for my Vornado VMHi300 - so it allows easy control from where we keep it on the floor. The original knob wasn't super accessible so we made it easier to toggle. Includes a small pointer for the mode it's on.
Simple print two of these and clip them onto the front of your tanks after filling. Any nozzle size should work, but a 0.2mm nozzle will likely work best. Any print settings should work.
Fan base I made to save some floor space. Made for my fan- the Vornado 602, but it may work for other models. The neck for the 602 is roughly 48mm in diameter, so if yours are similar spec, you may be in luck! That being said, I've…
Do you have a need to install a horizontal fan above a door frame? Perhaps you have a room that produces more heat than you would like, with no central air, and you need a good way to circulate the air. Then look no further than this…
I kept losing the Vornado silicone anti-vibration feet. Without the feet, the fan makes an annoying buzzing sound. These TPU feet prevent that noise. Depending on your shore hardness, it may be a bit difficult to insert these feet. Make a…
I bought this fan expecting to either mount it to my desk or figure out a bracket like this! It wasn't super hard to pop the stock bracket off and frankly the stock bracket feels like the cheapest part of the fan Rotate the STL slightly…
There are two models. One is smooth and matches the original knob. The one with a seam should force the slicer to place the z scar aligned with the indicator. The picture is the smooth version, where the seam is slightly misaligned. It…
I seem to always loose them Or it drops into oblivion. never again replacement feet for Vornado fans. please leave ⭐ review and rate. Buy me a some raman if i helped you out in anyway. https://ko-fi.com/3deeznutz Check out my other…
The Ultimate Vornado Humidifier Nozzle!!!!! Specially designed to impregnate your air with water. Mother nature is truly the best engineer. Print Settings Printer: Monoprice Delta Pro Rafts: No Supports: Yes Resolution: 0.16 Infill: 25%…
The rotary speed select knob fell off of my vornado room fan, so i modeled this new one. It connects to the fan using the D-shaped rotary switch on the fan. May work for other fans as well that use the same switch. It took a few prints to…
Fan friction fits into base. Works great at office desk.
This is a mount for the Vornado 173 fan. It uses the stock screw holes that are used to install the stock base. The ‘left’ mount has provisions to use a small bungie or zip tie to hold the fan to the mount if needed. The STL for the left…
