25 models
Build an ambient sound sensor. This small box fits a microcontroller and the sensor, is powered from USB-C and looks neat on the wall. My use-case: the sensor measures ambient sound levels in the room, and reports those to HomeAssistant.…
I present to you a 54x44 square cells, orthogonal maze. You have to start from center and the exit is at the bottom. The maze is a little bit hard to solve, but the time to solve it is worth it. The total maze size is 240x200x11mm. There…
a simple compact case for Max4466 breakout board/microphone. I'm using mine attached to a project box for a WLED Sound Reactive setup. The enclosure has 2 small pins to line up the circuit board and hold it in place, on the bottom is a…
Specs: 43.8mm inside diameter on eyepiece 51.8mm inside diameter to cover the 44mm lense Can probably be scaled to any scope size
Not too bulky. Just enough to grab or push with your thumb. Made out of PETG for Flexibility and Heat Resistant Use of a single #4 x 1/2" wood screw to clamp onto scope
Case for NodeMCU-ESP32 ESP DEVKITV1 and Max4466, to be used with WLED These are the ESP's purchased https://www.amazon.ca/gp/product/B0BQJ8BTVB/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 Tight tolerance so that the Max4466 doesn't…
I present to you a 54x44 square cells, orthogonal maze. The entrance is at the top and the exit is at the bottom. The maze is a little bit hard to solve, but the time to solve it is worth it. The total maze size is 240x200x11mm. There is…
Parallax wheel for VectorOptics Veyron 3-12X44FFP Rifle Scope is 52mm diameter ring to help focusing. It is a snug pressfit to scope parallax adjusting knob.
Ein Winkel für Vierkanthölzer
Magnetic rifle scope with fron 50 mm and rear 44 mm diameter. You need 12 pices of gagnet 6x2mm (Aliexpress) - https://www.aliexpress.com/item/1005005884332595.html?spm=a2g0o.order_list.order_list_main.15.8b511802zbc0Fz Scope is Meopta…
a parralax wheel for the FALKE 4-16x44
x44 micro sd card holder
Jack 3.5 is : Female 3.5-to-3.Screw-Terminals-Adapter
Divider for Ikea ANGELÄGEN box 25x44x17cm There are 2 parts : plate 2 feets (side printing) It is better to glue the feet with a point of glue. Print Settings Printer: Sidewinder X1 Rafts: No Supports: No Resolution: 0.2 Infill: 10%…
Simple end caps for two sizes of Swift Audubon binoculars, 7x42 and 8.5x44 from years ago. My original end caps started falling off so I designed these. Should be printed using TPU 95A filament. Fusion f3d and step file included.
Torx key handle for scope torx screws (T15). Fits torx key that is supplied with scope. Much nicer to use than plain metal torx. When printing add pause to end of layer +7.64mm and insert key mid-print. Key has to be inserted snugly to…
Small enclosure boxes for MAX4410 headphone amplifier boards, which you can get for cheap from Aliexpress. The lid is designed to be snap fit and can be closed relatively easy, but for opening it you may need to help yourself with…
The production guys broke the handle off of the switch for our vent fan to I whipped one up real quick. Printed from ABS, 4 walls, 50% hexagon infill. 3 solid top/bottom layers. This was specifically for the Dayton 2X441A switch but…
This is a 12,7x44 Swedish rolling block ammo box for 13 cartridges. Specially made for 13 shot blackpowder matches. Also for 12,17x44 which its exactly the same cartridge except its Norwegian naming. Printed in brown PLA but it will…
Small enclosure boxes for MAX4410 headphone amplifier boards, which you can get for cheap from Aliexpress. The lid is designed to be snap fit and can be closed relatively easy, but for opening it you may need to help yourself with…
Support piece to repair a broken headphone band. Peel back the foam pad and slide this on. Stick the foam pad back on. Optional - Add epoxy to the broken edges prior to sliding this on for an even sturdier repair. Printed this on the long…
I created a divider (168mm x 440mm) for my kitchen drawer. It creates 4 different sections, to fit longer pieces two of the sections are longer than the others. If you have any suggestions, on how to make the model better, just let me…
I made this box to mount electric window openers' switches, ordered on Aliexpress. There are two versions: 28mm and 44mm depth. 44 is standard, whereas 28 was exact fit for my particular switch. Depth and all other parameters is…
My tripod makes use of a QB-4W adapter which requires all 4 sides to be sloped, not just two. I loaded the original STL into tinkercad, performed a couple boolean operations to get the same slope, and preserved my dimentions on X and Y.…
