Counting matching models…
This is a range of panels for presenting XT60E-F sockets. I designed them to present XT60 12V power sockets in a campervan. But I imagine they could be useful for any number of situations where presenting XT60 power sockets would be…
Backpack module for 5" FPV quadcopters. Please do verify the dimensions of your quadcopter: backpack is 20mm high. Check that your frame has at least this height. mounting points are separated by 24mm (measured center-to-center) mounting…
This model allows you to mount a standard XT60 connector onto flat surfaces. ⚠ Note: It is mainly compatible with cheap, non-branded XT60 connectors. For example: it does not fit AMASS XT60 connectors. 🔹 Features: ✔ Fits both male and…
I couldn't find a good model of a cover for Amass XT-60 female (XT60E-F) panel mount connectors. This is a pretty close remake of the mass produced version I've seen from China before. Printed at 0.10mm layer height for detail. Do note,…
SpeedyBee Bee35 front XT60E-M mount. Remove 2 nuts from xt60 connector, and insert them into slots in part with same orientation. This part allows to move high current battery wires away from magnetometer in rear GPS module. V2 is version…
XT60E Mouting template for marking holes
i need to modd the battery connector of couple of NUI-N1 scooter batteries to use a more available type of connector, since the original connector was hard to find and expensive, so i came with this model that replace the original socket…
A cover for a modified (voltage upped to 13.5 V) HP server power supply for use as a ham-radio psu. It should fit other similar HP models (Dimensions H38.5mm x W86.5mm). The support part is being used to keep the psu level. There is a…
Original text, with adjustments: Designed this cover for the LRS-350-24 power supply unit. It has one XT60E-F socket and a C14 power socket, perfect for a 24V bench power supply. LRS-350-12/24/48 Power Supply: Here 1x XT60E-F Female…
I remixed the original backpanel to accommodate a female XT60 connector, so that I could use the DPS5005-based PSU with https://www.printables.com/model/322597-lrs-200-power-sleeve that I have built quite some time ago as a universal…
Przelotki mają pierścienie o średnicy 63.5mm Do drukowania potrzeba zastosować podpory w gniazdach XT60E-F Są dwie wersję.
XT60E-F connector xt60 connector
Simple housing for XT60E-F connector and USB-C PD trigger PCB. BOM: - XT60E-F connector - ZYPDS PD trigger PCB ( https://www.alexwhittemore.com/notes-on-usb-pd-triggers-and-zy12pdn-instructions/ can be found on amazon and aliexpress, see…
Cap for adding an XT60E-M plug onto a 65mm wide rectangular battery with spade terminals. I used it on a spare 65x151x94mm 7Ah 12.8V LiFePO4 battery to make it easier to quickly connect and disconnect from a 12V system. Requires:…
A Ninebot G3 charge port intended for the XT60E-F with the water seal lid. Fits with original seal and screws. Enjoy.
Saturn 2 Access Panel Right with the passthrough removed and the cuts for a surface mounted XT60e-F connector instead. I'm not very good with the 3D modelling software, so the STL file still has the lines of the passthrough visible, but…
Нигде не нашел, решил сам нарисовать крепление разъема питания XT60E-M для SpeedyBee Bee35. Сам разъем просто приклеил суперклеем, хотя и так входит плотно. Крепление выступом и задним болтом. Печатал пластиком PETG.
High Current Capacity: Integrated XT60E-F ports support up to 12AWG wiring, making it ideal for high-draw setups like 6-toolhead toolchangers. Industrial-Grade Data: Utilizes USB-C headers instead of standard USB-A for a more secure,…
Przelotki mają pierścienie o średnicy 63.5mm Do drukowania potrzeba zastosować podpory w gniazdach XT60E-F Są dwie wersję.
Backpack module for 5" FPV quadcopters. Please do verify the dimensions of your quadcopter: backpack is 20mm high. Check that your frame has at least this height. mounting points are separated by 24mm (measured center-to-center) mounting…
Based on LuKowalski's soldering jig I wanted to be able to do XT60E-F connectors, modified XT60-p10 to fit an XT60E-F connector. Use all other parts from the original
Mount for an XT60e plug. Designed for the SirenF5 Split frame by Quadmula, but should fit others frames also. Distance between the screws is 20mm. Print Settings Rafts: No Supports: Yes Infill: 50 Filament: Sainsmart TPU Category: R/C…
