Panzerjäger Tiger (P) Ferdinand (Sd.Kfz.184) mit Krupp Maus II Turm mit 150 mm Kampfwagenkanone KwK 44 L38

I created a two fictional or alternative types of models of Panzerjäger Tiger (P) Ferdinand (Sd.Kfz.184) mit Krupp Maus II Turm mit 150 mm Kampfwagenkanone KwK 44 L38 in size - scale 1:100 for model makers to the dioramats or like a model of toys to plastic soldiers figures or for gamers of table top millitary games :-) This model is not offensive and not have bad meaning!

A one day I saw on a Pinterest a model with name “Ferdimaus” by The AFV Factory. This inspired me to created this model. I added here some of original photos of “Ferdimaus” , but unfortunately I can not find dirrect link on Pinterest anymore, but I tried many times to find it again. :(

I took a one original model by Unitaz_38 from Printables and second model by SSBN506 from Thingiverse and combined it togegther with few my changes and recombination of some parts.  

Versions:

1. Panzerjäger Tiger (P) Ferdinand (Sd.Kfz.184) mit Krupp Maus II Turm mit 150 mm Kampfwagenkanone KwK 44 L38 A - Version A has a Krupp-type Maus II Turm fixed late turret with a 150 mm caliber Kampfwagenkanone KwK 44 L38 cannon in place of the original Porsche-type armored superstructure and the original 88mm caliber Panzerjägerkanone 43 PaK 43 L/71 cannon located in the rear of the vehicle. The engine compartment is in the middle of the vehicle's hull.
2. Panzerjäger Tiger (P) Ferdinand (Sd.Kfz.184) mit Krupp Maus II Turm mit 150 mm Kampfwagenkanone KwK 44 L38 B -  Version B has a Krupp-type Maus II Turm fixed late turret with a 150 mm caliber Kampfwagenkanone KwK 44 L38 cannon in place of the original Porsche-type armored superstructure and the original 88mm caliber Panzerjägerkanone 43 PaK 43 L/71 cannon located in the middle of the vehicle. The engine compartment is in the rear of the vehicle's hull.

Printing settings:

I did a .gcode in last version of Prusa Slicer for both Versions A and B, but Printables say about it “Unsupported file type”, so I can not add there here! I can't do anything about it! This is the first time this has happened and it honestly disappointed me… Bad Printables :( So I write here my setting and I used an organic supports.

If You try printing on normal FDM printers like my Prusa MK3S+, use a most detailed setting and I think it will be work as well. I think, that PLA is good on this printing. 

I personally not printed my Panzerjäger Tiger (P) Ferdinand (Sd.Kfz.184) mit Krupp Maus II Turm mit 150 mm Kampfwagenkanone KwK 44 L38, because I think, that better results of printing will be with Resin SLA 3D printer, but I don't have any one. 

After printing You don't have to use any sandpaper, glue, screews or anything like that, but if You want a better look of Panzerjäger Tiger (P) Ferdinand (Sd.Kfz.184) mit Krupp Maus II Turm mit 150 mm Kampfwagenkanone KwK 44 L38, You must paint it. I recomend an acrylic colours or airbush. It works well.

Also if You need some different sizes, You can take my models and resize them as you need :-)

I hope You like it :-D

Print settings

Printer Brand:
Prusa

Printers:
i3 MK3S+

Rafts:
No

Supports:
Yes

Distinction:
0.05 - 0,07

Filling:
15 - 25 %

Thread Brand:
Prusa

Thread color:
You can use Your favorite colour, but I recommend make a camouflage with acrylic colours or airbush

Fiber material:
PLA