1 / 4
Creality Falcon 2 40W Laser Crosshair Mount Bracket — zdjęcie 1
1 / 4

Creality Falcon 2 40W Laser Crosshair Mount Bracket

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Overkill Crosshair Laser Mounting Bracket

Ocena
0 / 5
Polubienia
7
Pobrania
107
Wydruki
0
Wyświetlenia
598
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a mount for the Creality Falcon 2 40W Laser Cutter to add a Laser Crosshair. I just wanted something sturdy and didn't move when I touched it and thought I might share :)  First ever upload, hope it works well for you guys (and hope I didn't overkill instructions.)

 

Materials Needed:

  • (1) - 12mm 3V-5V Crosshair Laser Module https://www.amazon.com/gp/product/B08D3LKQQG/
  • (1) - USB-C Cord (Sacrificial From Cheap Cord)
  • Heat Shrink
  • Solder
  • (3) - Hex Socket Head Cap Screws (M3 x 12mm)
  • (2) - Hex Socket Head Cap Screws (M3 x 10mm)
  • (2) - Hex Nut (M3)

 

Tools Needed: 

  • Soldering Pen/Gun
  • Heat Gun or Hair Dryer
  • Hex Keys

 

Print Settings:
(Printed on Creality K1 Max)

  • Layer Height: 0.16mm
  • Wall Count: 3
  • Supports: Yes (print model with top side down, may not even need supports but I added them anyways)
  • Infill: Grid or Rectilinear

 

Wiring Laser:

Take your sacrificial USB-C Cord and splice the wiring sheath open and you should see 4 wires (some colors may vary but should all be relatively the same). Use small heat shrink wrap to cap off the white and green wires. Remember to place all your heat shrink on your lines before soldering. One for each of red and black wires, then a larger one to cover all the wires.

Solder the Red wire to Red on the laser and the black wire to the black on the laser. Slide the heat shrink over and shrink it down on top of it all. 

Plugging the laser into a computer port may not turn on the laser. Instead try using a charging block to test it or plug it in your USB-C on your laser if you feel like you've wired it correctly to test it.
 


Mounting the Bracket and Laser:

On the top of the laser head, remove the top two front screws and the screw on the back left (you can reference the picture on my laser bracket for a reference point). Slide the bracket on and it should be a very close fit. Use the (M3 x 12mm) screws to secure the bracket to the top of the laser head.  

Use the two (M3 x 10mm) screws and (M3) hex nuts and attach them to the laser mount. One side has a hex nut recess and the other has a cap screw recess. Slip the laser in the mounting hole until the thumb screw part of the crosshair laser head is far enough out to where you can turn it. Tighten down the laser mount screws tight enough so that the crosshair laser doesn't slide up and down. 

 

Offset Settings for Laser:
(This is the offset I used in Lightburn, yours may very depending on differences of build and laser crosshair placement/type. Be sure measure and calibrate your offsets.)

In Lightburn:
Go to 'Device Settings', click ‘Enable pointer offset’.

My Offset Settings: (Your Offsets May Vary)
X= -42mm
Y= -37mm

Save settings.


Squaring Your Laser:

The easiest way I found to square the laser is to draw a square in Lightburn and burn it onto a throw away material. Without touching or moving the material, put the center of the crosshair at the corner of the square and then rotate thumb screw head of the crosshair laser until aligns with the sides of the box. 
 

Tagi