Liczymy pasujące modele…
Falcon2 Pro Collection This is a holder for a 5V 5mW laser crosshair pointer for the Creality 22w/40w/60w laser module used to line up material on the bed for cutting accurately and set back far enough so as to not collide with the front…
Falcon2 Pro Collection This is a bracket to hold a Wyze V4 or V4 camera($20-30 off Amazon) in place to observe your cutter remotely. The Wyze software to view your camera is free. I wanted a way to keep an eye on my cutting while in other…
Falcon2 Pro Collection I had smoke creeping out the crack between the exhaust hose adapter and the side of the enclosure as well as the hose connection where the wire wraps. I replaced the fan grill with this foam gasket cut from 2mm…
Falcon2 Pro Collection A TPU brace to hold your slats in place so they don't shift around when putting material on the bed to cut precisely. Print two sets to fully cover the slats in any orientation. Print as oriented. Default FLEX…
Falcon2 Pro Collection This is a set of half fan intake shrouds to help the laser unit not pick up particles from the surface being worked on to minimize build up in the cooling unit. Creality does provide instructions on how to pull the…
Falcon2 Pro Collection This is an intake shroud used to direct air over the cutting surface area. This requires you to cut a hole in your drawer. This tucks under the front so the laser head will not collide with it. This attaches to the…
Falcon2 Pro Collection These are instructions as part of my Falcon2 collection. The model is just a placeholder. The Creality Falcon can ship with a gantry that is not fully square. I had to perform the following to square the gantry by…
Falcon2 Pro Collection These are instructions as part of my Falcon2 collection. The model is just a placeholder. I needed to ensure my laser head is perpendicular to the surface where my material will sit since I plan to cut pieces of…
Falcon2 Pro Collection In order to quiet down the beep of your Creality Faclon2, you need to put a few layers of tape over the beeping module on the control board(red highlighted module) with blue tape already in place which is located in…
Falcon2 Pro Collection This is a fix to ensure the drawer does not shift. Why is this important? If you're wanting to work from the 0 X and 0 Y coordinates with a secured honeycome in the lower left corner, this will help ensure…
English: Simple and efficient magnetic clamping system for "Creality Falcon2 Pro" bed. Instructions: Purchase 10 mm cubic magnets. Print the clamps that match the thickness of your material. Attach the magnets to the base of the clamp…
Since most wood is warping and sometimes gets moved by the Air Assist, I tried to find a solution that works with the aluminum bars from the Falcon2 Pro. This material holder comes with a glider and a holder. The glider slides onto two…
Since most wood is warping and sometimes gets moved by the Air Assist, I tried to find a solution that works with the aluminum bars from the Falcon2 Pro. This material holder comes with a glider and a holder. The glider slides onto two…
Falcon2 Pro Collection This is a holder for a 5V 5mW laser crosshair pointer for the Creality 22w/40w/60w laser module used to line up material on the bed for cutting accurately and set back far enough so as to not collide with the front…
Falcon2 Pro Collection This is a bracket to hold a Wyze V4 or V4 camera($20-30 off Amazon) in place to observe your cutter remotely. The Wyze software to view your camera is free. I wanted a way to keep an eye on my cutting while in other…
Falcon2 Pro Collection I had smoke creeping out the crack between the exhaust hose adapter and the side of the enclosure as well as the hose connection where the wire wraps. I replaced the fan grill with this foam gasket cut from 2mm…
Falcon2 Pro Colletion This is a bracket that can be used to build a shelf that sits on top of your Creality Falcon2 Pro enclosure to provide some extra room for a laptop or the like. Two files - one with holes for rubber feet , one…
Falcon2 Pro Collection This is a door exhaust port I use for my laser cutter/engraver which uses a 75mm/3" hose. My door is 44.5 mm thick. You will need to print this: door_exhaust_port and one of these sets exhaust_director_short or…
Falcon2 Pro Collection A TPU brace to hold your slats in place so they don't shift around when putting material on the bed to cut precisely. Print two sets to fully cover the slats in any orientation. Print as oriented. Default FLEX…
Falcon2 Pro Collection This is a set of half fan intake shrouds to help the laser unit not pick up particles from the surface being worked on to minimize build up in the cooling unit. Creality does provide instructions on how to pull the…
Falcon2 Pro Collection This is an intake shroud used to direct air over the cutting surface area. This requires you to cut a hole in your drawer. This tucks under the front so the laser head will not collide with it. This attaches to the…
Falcon2 Pro Collection These are instructions as part of my Falcon2 collection. The model is just a placeholder. The Creality Falcon can ship with a gantry that is not fully square. I had to perform the following to square the gantry by…
Falcon2 Pro Collection These are instructions as part of my Falcon2 collection. The model is just a placeholder. I needed to ensure my laser head is perpendicular to the surface where my material will sit since I plan to cut pieces of…
this model il is using a 12x 16 mm rail to mount a camera using the enclosure tubular structure. the 4mm holes are designed for 3mm insert. to secure the assembly
These spacers allow you to position a 400x400mm MECPOW honeycomb bed relative to the feet of the Creality Falcon 2. The outside dimensions of the bed are 440x440mm The bed is also raised a few millimeters to allow fumes to escape under…
I created a material library file from Creality's suggested settings for the 22W Falcon2/ Falcon2 Pro. I have the Pro model but I am guessing the settings are the same among both machines. You can open this file directly in Lightburn.…
Falcon2 Pro Collection In order to quiet down the beep of your Creality Faclon2, you need to put a few layers of tape over the beeping module on the control board(red highlighted module) with blue tape already in place which is located in…
Falcon2 Pro Collection This is hardware to help add lighting to the top of the Falcon2 Pro laser cutter without wiring into the existing circuitry. This uses a USB powered light strip cut in to (4) 200mm sections with a prebuilt photo…
Upgrade Your Laser's Stability with Micro-Adjustable Legs Achieve perfect focus and alignment with these replacement legs for your Creality Falcon 2 laser. They provide effortless micro-adjustments thanks to a notched nut system that…
Cut with more accuracy and create cleaner fills using Lightburn. Scan alignment and dimensional accuracy guide This video covers both of these items. You can see both the before and after results in my images(6000mm/m 0.18 line shift was…
Uploading here for visibility - not my model but nice to have on my laser cutter to avoid oopsie moments killing a laser run. Printed in PETG.
I needed an 90 degree elbow for my Creality Falcon2 Pro 40w/60w, but one that would allow me to connect a 4"duct
I do not have a window close to my Engraver so needed to use Inline fan and other things to reduce the smoke leaking to my hose while engraving one additional point of failure has been the junction between the OEM exhaust or even the…
Falcon2 Pro Collection This is a fix to ensure the drawer does not shift. Why is this important? If you're wanting to work from the 0 X and 0 Y coordinates with a secured honeycome in the lower left corner, this will help ensure…
Per raiser you need: 2x 6mm nuts 1x 6mm x 20mm screw After inserting the nuts and the screw (be gentle) you can just click or glue the two parts together. Print with support. If you want to support me: https://www.paypal.me/letusgo2hell
The upgraded model also makes sure that the origin of the machine is in the corner of the honeycomb.
This is a quick remix of Dalton's feet for the Dofiki 500mm honeycomb bed. It is slightly larger than the TwoTrees.
Print Information: Printer: Prusa-Mini Filament: PRIMASELECT PETG Transparent Black Nozzle: Bondtech 0.4 Layer high: 0.2 Infill: 50% cubic Rafts: No Supports: No Gedruckt wird flach und nicht hochkant. Zum kleben verwendet man am besten…
Print Information: Printer: Prusa-Mini Filament: PRIMASELECT PETG Grey Nozzle: Bondtech 0.4 Layer high: 0.2 Infill: 30% cubic Rafts: No Supports: No Zum kleben verwendet man am besten Acrylklebeband wie Spiegelkleber oder aus dem Zubehör…
Zum halten werden nur zwei Kabelbinder benötigt, positionieren nach Wahl. Print information: Printer: Prusa-Mini Filament: Prusament PETG Galaxy black Nozzle: Bondtech 0.4 Layer high: 0.2 Infill: 30% cubic Rafts: No Supports: No
Verstärkungsplatte für Abluftlüfter der Schutzhülle des Creality Falcon2, da Orginal sehr labil.. Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: Infill: 20% Filament:…
The Falcon2 Pro laser cutter & engraver is a great machine. But they really botched the bed of the machine – the slats are a horrible, wobbly mess! So any engraving with fast Y-movement will jiggle the workpiece. Especially bad if the…
Outlet elbow for smoke extraction laser Creality falcon2 Pro, fit on fan. Design for better air flow. Petg, 0.4 or 0.6mm nozzel, layer 0.2-0.32mm, supports
Designed an alignment job for my Creality Falcon2 laser cutter. Provides about ~6mm (¼") offset from the plastic to where the laser actually hits (laser + PLA/PETG) = BAD. Includes posts to ensure minimal movement during alignment.…
