1 / 7
Nerf Printable Talon Stick Magazine 18, 15, 12, 10, 8 Dart Capacity — zdjęcie 1
1 / 7

Nerf Printable Talon Stick Magazine 18, 15, 12, 10, 8 Dart Capacity

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Printable Talon Magazines available in various capacities. Only hardware required is a spring - link in description.

Ocena
4,667 / 5
Polubienia
48
Pobrania
155
Wydruki
3
Wyświetlenia
1594
Oceny
3

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Outdoor Toys
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Post a make if you print! I would love to see it.

 

Printable Talon Mags in 8, 10, 12, 15, and 18 Dart Capacities

Only hardware required is a Talon mag spring. You can purchase these from me at the below link (Australia based - international shipping available), or source from elseware.

Buy Talon Springs Here

Overview
  • Minimal supports (only for lips)

  • Smooth inside surfaces for smooth follower movement

  • Two-part design means no warping from the bridging pulling inwards as seen on monolithic designs

  • Easy assembly

  • Many capacity options

Printing - See Images
  • Press the ‘Split to parts’ button in your slicer to separate all of the parts.

    • The rear wall part is flat and should have a smooth top layer when sliced. I have encountered a glitch in Prusaslicer where after splitting parts, the rear wall part cannot be properly placed on a face. If this happens try rotating the part with the rotate tool and then re try the place on face tool. You can also try exporting the split part from within the slicer and then reimporting it.

  • Make sure all supports are turned off in your slicer. Where supports are required, optimised snap-off supports are already designed into the model. 

  • Make sure to print all parts in the correct orientations. See images.

Assembly
  1. Peel off the bed adhesion tabs from the Base part.

  2. Snap off the mag lip supports.

  3. Put drops of superglue (PLA) or appropriate glue for your material in the slots on the rear wall part before aligning it to the tabs on the main body and pressing it on firmly. Make sure not to use too much glue as if you do it will get squished out of the slots and make a mess when the two parts are brought together.

  4. Once the glue is dry, turn the mag upside down (lips facing down). Insert the follower so it falls to the top end of the mag.

  5. With the mag still upside down, sit the spring inside and on top of the follower. If making an 18 dart mag, you don’t need to cut the spring. If making a shorter length: trim the spring with a pair of sidecutters so that it sticks out about 40mm from the base of the mag at rest before the base is attached. It is advised to also bend the cut end of the spring by hand or with pliers to make it square. 

  6. Compress the spring into the mag and clip on the Base part. The base part takes some force to clip in. You can try putting one end of the clips in first then placing the mag upright on a desk and pushing down on the body against the desk to clip the base in. Make sure the Base part is lined up properly and that the spring is not caught between the Body and the Base parts.

    • Tip for attaching base part - compress the spring and put a thin object (I use a long hex driver) through the slots in the side of the mag to stop the spring interfering with attaching the base part. Once the base part is attached you can remove the object to let the spring expand. 

Troubleshooting
  • If the follower does not move smoothly, try filing or sanding the sides and ends of it. With an accurate printer such as a MK4, it should run smoothly with no post processing. 

Disassembly

You can remove the base part simply by pulling on it with significant force. I have found using a large pair of side cutters to pry it off as pictured in the last image works well. 

Changelog
  • 30th October 2024: Rear wall is now a separate piece that is glued on. Avoids bridging on the inside which caused issues with the follower.

 

Check out my improved/modified parts for the Zinc 2.0:

https://www.printables.com/model/720257-zinc-20-all-improved-parts 

Tagi