Liczymy pasujące modele…
Converts the Kirin angled talon magwell (from Shellington Labs) to be single dart loading. In prep for a no-mag event, I found I didn't have any old-school blasters at the right FPS. There's a single load mag block for the SLAB and that…
Replica of a Peregrine Falcon Talon. Designed for my son's school project (Blender). Used as a custom pointer and demonstrative material in his presentation about the Peregrine Falcon :) Printed in 2 halves that need to be glued together…
Hello everyone! This is a four dart capacity short dart/talon style magazine designed to work specifically with my Springer Rayven blaster. One of the main goals of the springer Rayven project was to keep the Rayven looking as original as…
1GB Plymouth Laser/ Eagle Talon/ Mitsubishi eclipse Side marker light clip MB596509. I recommend printing on resin printer. Might need some sanding. It is exact copy of original.
This is a two part model, GPS bracket is glued on the base of the FC bracket. FC bracket is designed specifically for the JHEMCU F405 Wing but has 30(31)mm spacing so in theory any FC with matching hole spacing should work. GPS bracket is…
This is a glueable tow hook for Micro Talon. Print on one of the flat sides. 2 walls with 40% infill is sufficient. Use attached photo for placing the part.
this (probably) fits most talon mags and standard picatinny rails Printer: Creality Ender 3 v3 se does not require supports infill density 15% or more any filament that is NOT TPU can be used to print this. If you've already printed this…
This magazine is built to utilize Lanyard pulleys as the spring for your talon mags! Made to be cheap and accessible to anyone with a 3d printer anywhere in the world without needing to buy springs or magazines from other companies!…
The S400 Talon Magwell is a 3D-printed magwell for the ZWQ S400 Zebra Bullpup Blaster designed by Luke Goodman at Out of Darts. Featuring a standard talon magwell with a rear paddle mag release, this part is an upgrade from the magwell…
The assembly process is practically the same, just put one angled dummy as the first one and other 6 dummies should be the standard ones. From my tests the 34 round version feeds very reliably in my worker phoenix 2.0 on max rate of fire,…
Aside from reinforcing the clamp, the magazines now point in opposite directions. This is to allow for reload by spinning the pair, and based on how you setup your pair the spare magazine will always be on the left or right side (your…
'Wolf Pack' is a modular magazine pouch system for foam dart magazines. This is the Talon version designed for Straight-, Angled- and Mini-style Talon magazines. Some key features: Compatible with Straight-, Angled- and Mini-style Talon…
takes some 1/4 in rods for the handle and rod for the hinge. could use 6mm x 2 mm magnets for the mag as the hole is around 6mm/0.24 inch. had a removable mag, and is split for printing. Category: Props
I found it best to print in PETG as the whole thing works much smoother. Untested with the PETG spring from Freddy Z as in theory this would require a longer bed to have the correct compression. No Supports are required 15% Infil Make…
Just a little remix of the best magwell adapter for the Dart Zone Stryker 2.0
Parts to make the 98k compatible with talon mags, if you need more ammo capacity. Replace the trigger group and pusher on first install, then you can swap from internal to external magazine by just unscrewing the 4 screws in the mag…
a holster to mount on your helldiver thigh plate. screw the dove tail on your tight plate and then you can slide the holster onto it. the dove tail works for the talon and senator holster(v2 of both of the guns of my model) (dovetail for…
This uses no additional screws to attach a half dart mag holder to the Worker Seagull (use the screws from the original picatinny plate). This works on either side of the gun and you could even have one on each side without really…
A completely useless thing to put on the internet but I thought if I needed one then maybe someone else might too. This replaces the side piece that the screw which holds the scissors together goes into. I had to use a 1/16th drill bit by…
So there is multiple versions: Blank Version 20mm Camera Mount Version 20x20mm VTX Mount Version CAM + VTX Version STEP files of the blanks so you can customize your own ;) A 1.8mm 1.2mm Wall thickness Version. Would recommend 1.8mm for…
Syncline is a low hardware compact mag holder designed to hold Talon mags. Instead of elastic cords or relying on the flex of the plastic itself, Syncline uses two panels printed out of a rigid material and elastic side and bottom panels…
Straight Talon DRUM SPRING Mag [ 12 / 17 / 20 short darts ] --> for DRUM SPRING --> Horizontal Print --> shorter, rectangular feed lips to be compatible with more blasters (e.g. ONTOS and MULTI-TOOL) Since my MULTI-TOOL and ONTOS don't…
I changed the length, should be able to print it on a A1 mini now if you lay it flat at a 45 degree angle. Hope somebody finds this useful. :) P.S. Leave a like
Sillybutts made a great remix of the Smiley ram base that improves upon the geometry of the -123 o-ring grooves so that they're easier to print without supports. However, the ram base included with the Talon remix of the smiley has…
Today, I stumbled upon a poor Bigshock with a snapped plunger. The little one could be saved, and so I did. The Posibilities for a compact shotgun pistol were something I had in mind with it. I remembered the design of thepaperskeleton…
I'm not 100% that this part will fit as my frame was bend back into shape after crash. Be carefull when installing it as clips are wery brittle. Send me feedback and i will fix the part. Use heat resistant filament.
Update 4-30-26: This blaster is now obsolete, as this is better in nearly every way https://www.printables.com/model/1699295-talon-fang-u-mk2-and-miniclaw-part-addons Though it does use parts from this. Update 1-29-20: Fixed trigger slop…
Supporto per pantalone/maglietta Trouser/T-shirt support Category: Audio
Wanted to do an improved version of gibbles_fx " NERF BigShock Removable Barrel (Elite Dart and Rival HIR)" I added knurling to the barrel end and also made the tolerances fit better in the blaster. Two files attached. One is default and…
Blaster overview: https://www.youtube.com/watch?v=glRXdd7pP-U Printed plunger tube overview: https://www.youtube.com/watch?v=QpMW5P51Vow Full assembly video here: https://youtu.be/Mo5sGpauzpw?si=SMMSYdP7EJdTvixH This is the Low Hardware…
These are mag holder inserts for the BlitzShorta foam dart magazine carrier system. I created a version of the insert for both the Zinc 2.0 and the Nightingale magazines. Added text to all, and to Spyder's Angled Talon version, and to the…
A knife whose blade is in the shape of a talon. The Finger cutouts use the average male ring size of 20mm diameter. Scale model as needed using your ring size in the chart below. Ring Size (US) Diameter (mm) Scale Factor 5 15.7 0.785 or…
UPDATE 10.04.25: updated version availabkle here: https://www.printables.com/model/1261173-printable-talon-magazines-v2 UPDATE 02.01.25: added .STEP file. Pretty space efficient printable talon magazines requiring one drum spring each.…
UPDATE 10.04.25: updated version availabkle here: https://www.printables.com/model/1261173-printable-talon-magazines-v2 UPDATE 02.01.25: added .STEP file. Pretty space efficient printable angled talon magazines requiring one drum spring…
This adaptor was tested on a bambu p1s and tested on a nerf sprinter. i do not know if there is any compatibility problems with other blaster that take the n1 mags, or tolerancing problems with other printers. the spring it takes is…
Watch the build video here: https://youtu.be/-DZQGRVDaHU I had the idea of converting this blaster to use angled Talon mags. Figured I could make an adapter, a brass pusher and a brass barrel pretty easily. The adapter took the most…
Remix of @upwdesign's, @flygonial's, etc designs because I really love the "open" remix for the full-size talons.
A replacement lower for the Rush by shoelesshistorian. It is compatible with both Angled Talons and Nightingale Mags. It also features an ambidextrous and extended push button mag release. Only additional hardware is a M3x12mm socket head…
Talon knife inspired by Counter Strike Can also be printed on small bed printers like the a1 mini or prusa mini. Print as detailed as possible - for the blade I used a 0.2mm nozzle and a layer height of 0.06mm. Theoretically no glue etc…
A small Talon Knife with 2 finger holes. Perfect for opening boxes!!The Finger cutouts use the average male ring size of 20mm diameter. Scale model as needed using your ring size in the chart below. Ring Size (US) Diameter (mm) Scale…
can be printed together the model needs to be glued together or separately in other colours can be printed without support the T-38 is very realistic Print in place kit card , Assembly required
TinTalon Makerchip Used K2_Kevin's Makerchip template: https://www.printables.com/model/833838-makerchip-maker-chip-the-new-maker-coin
Gen-2: now with interlocking tabs! This is my Simple 3D Printed Talon Clone. This Worker mag clone is designed to be a no-nonsense, easy to print, and durable magazine. the outside body is almost 100% identical to a Worker Straight Talon.…
3D Model of a Etalon micrometer, used to design a box to store it. Want to support me? => Have a look at my USB power supply mod (5V/1A) for Prusa MK4(S)/3.5(S)/MK3(S)(+) and Prusa XL, perfect for powering Buddy3D cameras or similar:…
Converts the Kirin angled talon magwell (from Shellington Labs) to be single dart loading. In prep for a no-mag event, I found I didn't have any old-school blasters at the right FPS. There's a single load mag block for the SLAB and that…
Size allows these to be printed in any plastic and be functional, shown is Overture TPU, would recommend TPU with 3 walls and 15% gyroid infill to fully support and leave it squishy enough to avoid risking damage to the outer extrusion of…
I found the original Foxbat straight talon grip uncomfortable, so I extended it down a bit. However, it is still compatible with Koda Mags. I also changed the trigger guard a bit to improve comfort.
17 rounds base capacity +8 rounds with extension. Hardware can be found here for cheap: https://moosemodshop.com/products/drum-springs-magazine-hardware
UPDATE: Now includes v3.1 of the 10 round mag with slots for drum spring. (sorry I missed that one) ---- This is a fully printable half dart compatible 10 & 15 round magazine with some nifty options. (as shown above with my soon to be…
Post a make if you print! I would love to see it. Printable Talon Mags in 8, 10, 12, 15, and 18 Dart Capacities Only hardware required is a Talon mag spring. You can purchase these from me at the below link (Australia based -…
Introducing the 1:578 scale model of the Talon-A, a cutting-edge hypersonic testbed designed for next-generation aerospace research. The Talon-A is part of Stratolaunch's ambitious project to explore hypersonic speeds, capable of reaching…
HORIZONTAL Print - Slim Angled Talon Short Dart Magazine / MINI Angled Talon Magazine (13, 10 and 8 darts) This is a remix of the horizontal print magazine by Astropulse which can be found here Horizontal print 31K/Diana magazine von…
HORIZONTAL Print - Slim Angled Talon Short Dart Magazine / MINI Angled Talon Magazine (13, 10 and 8 darts) This is a remix of the horizontal print magazine by Astropulse which can be found here Horizontal print 31K/Diana magazine von…
A squared-off remix of KingDeeddee's Bk1s/2s talon magwell sleeve . Instructions to assemble are identical to the original. Print magwell base facing down, with supports.
This is my CS:GO talon knife made in fusion360 using in game images as reference. Here is a stand for it :> ← Update 2 !added decorated handles! one piece / multiple piece versions To assemble it with the old handles you will need three…
Follower - for Talon Springs - Sure.t Nerf Mod Talon Magazine A follower for standard Talon springs for the nice combination mod by Astropulse Sure.t Nerf Mod Talon Mag - Fully Printable - Quick Assemble/Disassemble I shortened the…
Retaining pin for the cubby door in 2017 or newer Honda Ridgelines 71509-SZA-A01 Also fits the Honda Talon Air Cleaner Outer Cover - (thanks @JustSomeEngineer !) : Recommended Print Settings Print Orientation: Default as modeled Material:…
Ergonomic grip (Angled Talon) for the Foxbat so that this giant hand cannon blaster lays better in your hand. This is a remix from the standard grip of the Foxbat expanded with a segment of the rear area of the universal pistol grip. I…
Display stand for my CS:GO Talon knife to assemble it you w anill need glued any m3 screw will fit(min 8mm max 18) assembly is quite simple step1. get your parts stehp2. look at the photo of the stand step3. put everything together and…
this is remixed from a model on thingiverse Talon mag holder by Aristogen - Thingiverse plz like and post a make! it encourages me to create more! Print Settings Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 15-25% Filament brand:…
This mount is designed to allow the DJI Digital FPV system Air Unit to be mounted under the front hatch of the ZOHD Nano Talon Evo. It is intended to sit under/behind the naca duct and provide some space for good airflow to cool the Air…
A simple mod for the Talon Claw 4 to prevent the Clevis Pin from falling out. Requires a 008 O-ring.
Replica of a Peregrine Falcon Talon. Designed for my son's school project (Blender). Used as a custom pointer and demonstrative material in his presentation about the Peregrine Falcon :) Printed in 2 halves that need to be glued together…
Holds 2 reversible talon holders with belt clips to slide onto whatever. May need sanding to get the talons going in an out without enough force to slip the holder off a belt. I print with the top cut off in slicer to enable toploading…
Mag holder but with a paddle release. Make sure to hit the paddle before pulling down or the catch will get stuck bent downwards. Dart zone mags don’t seat all the way up because of the talon catch point, but they still hold under the…
Print orientation like katobu mags. Front and Back on their respective front-/backface. A foamblast style drum spring is recommended though a magazine spring sized for half lengths should work aswell. Highly suggest printing the back…
Do you want to use straight worker talon style mags in your Fury X? Look no further, this small replacement will solve that issue! Just remove the old mag release part, and swap the spring to the new one. This is much more secure, and…
NOT TO BE SOLD BY FRONTLINE FOAM OR BLASTERGUYS POTATOFEEDERNERF IS ALLOWED TO SELL OFF REMAINING STOCK UPDATE 29.08.25: added a 55mm neck option UPDATE 09.08.25: updated the .3mf with the newest parts UPDATE 31.07.25: Modified the necks…
A SKADIS wall mounted magazine/clip holder for your Nerf armory. Features Holds 4 talon or 4 full length clips Holder can be mounted upside down Mags can be mounted in either direction Fence-like wall decreases filament use and print time…
Protect your talon magazines from harsh ejections and accidental drops on hard surfaces! This should also help reduce instances of spontaneous magazine disassembly. All four tabs inside the part should engage with the four holes towards…
Use cases : This is my creation of a key ring of a Catalonia circuit - Barcelona-Catalunya. Impression : PLA or PETG Please give this design a like if you like it, or post a photo of your making! Good impression! Cas d'utilisation : Il…
Adapters for Straight and Angled Talon Magazines. Hot swappable and doesn't need to trim the reinforcing ribs in the magwell. Requires a modified pusher to work with it. Check this collection for more detail. After inserting it, pull the…
Nerf blaster display stands for blasters using the Talon magazine geometry in extra large.
I liked the idea of the original P-SAT, but I had two issues with it. First, the catch hole was too low for the Nightingale and Venom Pro. Second, it wasn't long enough for me. So I fixed both. This is designed to print on my P1S, so…
14/6/2025 Reuploaded correct file for bumper part 1 (Another design I forgot about) Prints in two parts, plastic upper and a TPU bottom. Knurling for grippers. Parts connect to each other with a dovetail and a detent, may need a dab of…
Infill: 15% Gyroid Walls: 4 Supports: Organic/Tree Orientation: default It slid onto my Dart Zone Max Venom Pro pretty smoothly.
Inserts for your micro rig style vests that converts each standard mag holder to hold 2 talons.
NOT TESTED I don't see any gaps in the preview so I think my bodging should work fine. Capacity is untested until my test print finishes. Included files: A 3mf project file of all parts from the original model with mine modifications as a…
Model can be printed horizontally with the dart count facing up. It will need support for the top lips and possibly a touch at the beginning and end of the mag roof (support on bed only). With the correct settings (0.25mm top support gap…
I used 1.5 mm layer height and a 0.4 mm nozzle for everything except for pistons, which I used 0.5 mm layer height and 0.2 mm nozzle.
split for smaller printers, may updated once the warbond is officially opened and i get a better view. takes a ½ in dowel Category: Props
Hello everyone! This is a four dart capacity short dart/talon style magazine designed to work specifically with my Springer Rayven blaster. One of the main goals of the springer Rayven project was to keep the Rayven looking as original as…
1GB Plymouth Laser/ Eagle Talon/ Mitsubishi eclipse Side marker light clip MB596509. I recommend printing on resin printer. Might need some sanding. It is exact copy of original.
yeah its just quiver if it were worse https://www.etsy.com/listing/1722696789/v3-pro-quiver-series-3-talon-mag-carrier 2 detents recommended if you run the mags upside down https://www.amazon.com/dp/B08SWDZ8ZG
Originally released in 2019 moving to printables Lepus Mk2 XT-TK (eXposed Trigger - Talon + Katana) Variant The Lepus is a fully custom designed Nerf blaster that is about as small as you can make it. It uses worker Talon mags and worker…
These are as close to 1:1 as I could do, with a few minor tweaks to make them lighter, they're very close to the original's weight, but are stiffer. They were made in Ondsel/FreeCAD. Use an M3 threaded insert for the wing brace. I printed…
remix of https://www.thingiverse.com/thing:6245333 and https://www.thingiverse.com/thing:4747632 it requires 1x M5x25 screw
UPDATE 17.08.25: modified straight version to fit better into flycore blasters and added bumpers, these can be printed out of TPU or the same filament the rest of the mag is out of This is version 2 of my printable talon compatible…
two magazines that are the maximum size of my 3D-Printers' build volume. the ender 3 one should fit ~25 darts, the ender 3 max one should fit up to 35. a relatively stupid experiment, but they work and you can have the files.
Rather than having to empty worker talon mags by hand this little tool can empty mags in record time. Its very simply to build requiring just 2 m3x8 cap allen screws (longer screws in the handle will bulge the wheel and cause rubbing).…
I designed this magazine adaptor using a 3D scan of the Dart Zone Max Stryker 2.0 so the shape of it better follows the rest of the blaster. It is also shorter, and has much bigger flair to the magazine well including opening up one side.…
A holder for a talon mag used in nerf, I made it because I only have two and the og was bulky.
Hi, This is motor mount for Mini Talon FPV Plane. M3 nuts are placed inside the print, maximum thickness of nut is 3mm. I used 2,3mm thick nuts, which worked fine on this project. You can use 10mm dummy on opposite corner of printing area…
A small mesh edit based on this https://www.thingiverse.com/thing:4938661 , but for the talon claw U and threaded rod version. 2 variants- One full rail as much as it can go. One that is slightly longer and has the chamfer that is on the…
Update 11-17-21: Added a super long version that is the length of the banana one I made earlier. A mag extender for the OOD tachi mag. Adds a simple cutout for the retaining tabs. Sand if it cant insert. Do not use Silk PLA for this as it…
Converts the 3 5.56 mag ACE TAC rig to a 4 talon mag rig. Mine was printed on a P1P using normal settings since its not going to be going any high stress.
Minimalistic base without eyelet for the printable angled talon magazine from Taffert Designs. The file is already pre-oriented. My print settings for PLA: 0,2mm layer height 4 walls 20% gyroid (or cubic) infill 7 top and bottom shell…
![Space Efficient Printable Talon Magazines [OUTDATED]](https://media.printables.com/media/prints/1007060/images/7659382_c86dfabe-2414-4e67-b6d2-83e552e16870_67018f36-49a7-44a0-97d0-d84225e66d22/img_20240830_172621.jpg)
![Space Efficient Printable Angled Talon Magazine [OUTDATED]](https://media.printables.com/media/prints/1007073/images/7659457_0e9bebde-ee43-433a-b9af-c05f9a7557e7_5d6e626e-eb74-471a-955a-4755339ba1c2/img_20240914_164654.jpg)
