1 / 6
PLAinberger v1 - A 3D printed headless Bass Guitar — zdjęcie 1
1 / 6

PLAinberger v1 - A 3D printed headless Bass Guitar

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This project was inspired by the Prusacaster 3d printed guitar made by Mikolas Zuza and the iconic 80s STEINBERGER bass

Ocena
0 / 5
Polubienia
41
Wydruki
0
Wyświetlenia
1678
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Music
Licencja
Standard Digital File License

Demo:

 

 

I wanted to design a portable bass that would be inexpensive and at the same time easy to print.

I have a Creality K1 (22x22x25) so can’t print the core of the bass in just one part so had to print in 2.  I used 2 40cm 8mm metal rods as internal truss inserts and they have been great in holding the tension of the 2 main core parts. 

 I also used the lightest gauge string I could find Rotosound RS66LA Swing Bass 66 (30 50 65 85) which are amazing I have always avoided light gauge strings thinking of losing tone but they feel and have great tone.

 

UPDATES

4/11/2024 Update:
-Added a snap joint option version. The joints are only visible from the back of the bass. New parts are labeled as "Plainberger-wjoints". Parts are oriented to print.

-Added a 9v battery slot option on bottom left side part if you want to go Active. Oriented to print with battery hole facing down (needs supports) .

-Added STP file to allow for easier editing and modifications. 

 

 

Overview of the pieces: 

(an uncut whole body file is also included in downloads)

 

 

 

Hardware

·        Bass Neck: I couldn't find a headless bass neck so i got a basic standard bass guitar neck for precision and jazzbass from Pitbul guitars and chopped off the neck with a saw: PBG-BN4M Maple Neck w/Maple Fretboard for JB and PB Style Kits. This part is out of stock.

Here are the measures it had and that I used to make the pocket for it. If yours does not fit this measurments i can happily adjust the pocket for your neck, contact me via printables or send me an email to [email protected].

 

 

 

·        Two 8mm 400mm metal rod inserts.

·        Bridge ( the part that holds the strings in the top of the neck has really small holes and had to drill bigger size holes to fit the bass strings; it’s the cheapest option you get what you pay for)

·        Back Neck plate.

·        Pickguard screws.

 

Electronics

·        Pickups

·        Volume and Tone Knobs

·        Wiring Harness 

 

Printing the parts:

 All the parts have been printed in regular PLA. The 2 core pieces have a infill density of 35% and 6 walls. The blue and orange parts are not under the tensile forces so you can play with lower strength settings, i printed them 15% 3 walls. Regular Orca slicer supports where used in the pickup and bridge slots only and not in the rod insert or screw holes.

 

 

 

Assembly

 

I noticed a slight gap of about 2mm when I joined the two core pieces with the rod. I applied heat from a torch to one end of the rods, allowing them to melt seamlessly and sit securely inside.

 

 

 

 

 

 

 

Any superglue will work great with PLA try to get a GEL one like the one in the picture which is much easier and cleaner to work with.

 

Screwing Hardware directly into holes. You want a snug careful fit and avoid overtighting.

 

 

 

 

 

 

 

 

 

New Leg rest & new pickguard

I made an optional flip down leg rest Steinberger style . I used some superglue and inserted 2  screws to secure it.  This part prints flat no brim nor supports as it's a print-in-place hinge.

 

 

 

Tagi