1 / 2
3M Air Filter adapter to 120mm blower fan - clean the air in your enclosure — zdjęcie 1
1 / 2

3M Air Filter adapter to 120mm blower fan - clean the air in your enclosure

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Adapter that lets you connect up a 3M respirator filter cartridge filter to a 120mm radial blower fan.

Ocena
0 / 5
Polubienia
11
Pobrania
34
Wydruki
0
Wyświetlenia
284
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

So, as it turns out, even “benign” materials like PLA and PETG emit fine particulates and VOCs when you print. My printer lives a few feet from my desk in a not particularly well ventilated space. This adapter allows you to connect a 3M respirator filter (e.g. https://www.3m.com/3M/en_US/p/d/v000075263/) to a 120mm blower fan (e.g. https://www.amazon.com/dp/B0CSF9CRKJ) and mount it in an enclosure with your printer. It works. Be aware that it can cause warping; maybe don't turn on the fan until a few layers have gone down.

I'm not entirely in love with this model; it requires support, and the dimensions aren't perfect. I've included a STEP file if you want to mess with it. It you print the main adapter in PLA, it's really easy to break the bayonet mount, don't force it. A gasket is required for a good seal; the filter provides a lot of resistance to airflow, so any leaks will let the air bypass the filter. (I've included a gasket you can print in TPU.) Speaking os a good seal, I modeled a gasket for where the adapter connects to the blower fan, but then just sealed it in place with hot glue. That worked quite well. If I were to do it from scratch, I'd consider making the whole thing in TPU.

Anyway, I said it works. I own an anemometer, so I was able to do some testing. With the fan I got and a benchtop power supply, the blower pulls air through at 0.8m/s at 12v, 0.6m/s and 9v, and 0.4m/s at 7.5v. Accounting for leakage, 12v will pull 0.0017 square meters of air a second through the filter. That's not a ton, but it's enough to pull the volume of air in my enclosure through every minute.

That's of course, is just theory. I also own an air quality monitor, so I was able to do some real-word testing. Running the filter fan during and after printing has eliminated particulate matter in the enclosure (below my monitor's ability to detect), and does reduce the VOCs, though slowly. It does keep them down to a level low enough that I can't smell anything in the room while printing with the filter running, even if I've been out of the room for a while.

Regarding warping: I built my enclosure primarily to deal with warping causing my prints to curl off the bed. If I run the filter fan full blast from the start of the print, I've still gotten warping. However, if keep the fan off for the first few layers, then turn it on low for the next few, and then finally turn it on full blast, I haven't experienced any warping.

I wouldn't endorse hanging out in the same room as a printer that's printing out ABS or whatever, but better with something like this than without. 

I'm not done with this project; I plan to add a diverter vent that lets you switch from recirculating the air in the printer enclosure to blowing filtered air out. This should let me more effectively purge the air and cool everything down after printing. Stay tuned!

Tagi