Tyco RC 18650 Battery Case - Monster Jam cars, circa 2000
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
The original NiCad battery packs for this early-2000s RC car is long-since shot. So I put 18650s or a LiPo in there.
- Ocena
- 0 / 5
- Polubienia
- 10
- Pobrania
- 31
- Wydruki
- 0
- Wyświetlenia
- 431
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- RC & Robotics
- Licencja
- Creative Commons — Attribution — Share Alike
What Is It
I was asked if I could find and print a replacement battery pack for a 20-year-old Spider-Man RC car. When I couldn't find it, I decided to build it.
Parts Info / Assembly
There's two ways to go about this. 18650s, or freestyle.
Two 18650 Batteries
My original, and fancier assembly takes four parts:
case-bottom- You'll see four arms reaching out with cylinders cut out of them. A 3x4x5mm heat-set insert belongs in each one.
- Windows cut out of the back corners line up with the RC car's power terminals
- You'll want a nice, flat conductive surface filling out most of that empty perimeter, to ensure the car's terminals make a good connection, reliably
- L-shaped walls are nearby to serve as something to mount / attach to
cradle-bottom- Intended to be printed in TPU, to be gentler holding the battery
- Two nubs at the front and back will affix it to
case-bottom. This further makes it necessary to use TPU, because you'll need to bend/arch the thing to be able to slide it into place - At the front, there's a slot cut through the median, intended to let a conductor pass through to connect the battery terminals
- At the back, two notches are clipped out of the outside edges, for the same reason, but the back is where you'll need to complete the circuit to the car's power terminals, out to the sides
cradle-top- Same stuff, but with some notches cut out where
case-bottom's heat-set-insert receivers crowded it.
- Same stuff, but with some notches cut out where
case-top- Features four 3mm holes that line up with the heat-set inserts on the bottom. I'd also use a washer on top.
Freestyle (I used a standard 7.4v Li-Po RC pack)
If you'd like to use another battery type, you're mostly on your own for keeping it snug, because when I decided to change batteries, it was almost Christmas, and I really wanted to present it then. So, you'll ditch cradle-bottom and cradle-top, and … figure out another way to prevent your battery jangling too much.
I still think the main case-* designs are pretty cool. It slides in real nice and fits like the OEM packs.
So, you'll need case-bottom, and either case-top, or case-top-roomy.
| case-top | case-top-roomy |
|---|---|
| Was too tight for me to tuck all the LiPo pack's thick wires and connectors inside without expecting damage | Room to let those fat, high-current-draw leads bend with less crampage. |
| Maintains a pretty low profile, barely protruding any more than the OEM pack | Juts out more, could be a hang-up hazard depending on where you're driving it |
| Basically no daylight between the heat-set insert and case ceiling | Plenty of space between them. Thank goodness there's four of them, so these giraffe necks don't get wobbly |
Further Assembly - Electrical Connections
- Battery to Case
- If you're going with 18650s, there isn't much room left for the battery circuit. I recommend nickel plates, like those used for spot-welding.
- Use one to wire the front-side battery terminals together
- Two more (separate) smaller plates to touch on the back-side terminals
- Else you probably know a good way to get your battery connected
- If you're going with 18650s, there isn't much room left for the battery circuit. I recommend nickel plates, like those used for spot-welding.
- Case to Car
- Plate up the windows in the back corners with something smooth and conductive. These are what will wire to the car, pretending to be a 2003 NiCad battery pack.
- Finish
- Solder some wire between each back-side battery terminal/connector and its corresponding output window conductor
Links
- Onshape document: right here
- Mattel's product page for my target toy, the Spider-Man Monster Jam RC
- 3x4x5 heat set inserts: on Amazon link