1 / 8
How to add 115V/220V AC Chamber heater to Creality K1 Series or any klipper printer — zdjęcie 1
1 / 8

How to add 115V/220V AC Chamber heater to Creality K1 Series or any klipper printer

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Installation for a 115V/220V AC Chamber Heater Creality K1 Series or any Klipper printer Voron. CFG file included

Ocena
0 / 5
Polubienia
72
Pobrania
191
Wydruki
0
Wyświetlenia
3577
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Public Domain

WARNING: Disconnect your printer from AC power before proceeding. Death or serious injury may result from attempting to work on your printer while it is plugged into AC power.

How to install a chamber heater the safe way

My main gold is to make the chamber heater as safe as possible. The setup as multi safety for the 115v/220v heater element: 

  • 40 amp SSR
  • heater element control by a relay that connected to the heater fan (this make the heater element go on only if the fan is working)
  • Normally close thermostat that open at 75℃ to close the heater element
  • Inner sensor for shutting down klipper if heater element passed 125℃ 
  • Fuze on ac voltage.
  • HeaterFan will stay on in till the chamber sensor reaches 40°C. This will make sure the heater element is getting cold off will it turn off

YOU NEED TO CHOSE THE SENSORS AND TEMPETURE SETTING IN CFG FILE TO FIT YOUR NEED, I ONLY GO UP TO 60℃ IN MY CHAMBER

 

**Disclaimer: Use at Your Own Risk**
I am not responsible for any damage caused by this mod. Proceed at your own risk.

Bom list:

  • Qibi Plus 4 115/220v Chamber Heater (chose your voltage for your country) or make your own (use Nylon if you make your own)
    115v/220v heater

https://www.aliexpress.com/item/1005007804483549.html?spm=a2g0o.order_list.order_list_main.5.447018021uSe0W

  • BTT SKR Pico, Mellow Micro 4 or use existing pins on your printer motherboard (MAKE SURE YOU CHECK AMP AND VOLTAGE RATING FOR THE PINS USED)

https://www.aliexpress.com/item/1005007091558188.html?spm=a2g0o.order_list.order_list_main.67.447018021uSe0W

https://www.aliexpress.com/item/1005006043530249.html?spm=a2g0o.productlist.main.1.65f46d58NE2FWj&algo_pvid=62e33691-282f-448a-bee9-65ef65d20797&algo_exp_id=62e33691-282f-448a-bee9-65ef65d20797-0&pdp_ext_f=%7B%22order%22%3A%22301%22%2C%22eval%22%3A%221%22%7D&pdp_npi=4%40dis%21CAD%21102.32%2134.79%21%21%21505.04%21171.72%21%40%2112000035474707617%21sea%21CA%21121095306%21X&curPageLogUid=x6UJtjEHY25c&utparam-url=scene%3Asearch%7Cquery_from%3A

  • 24V 30A One Channel Relay Module

https://www.amazon.ca/dp/B0CFY5CB2V?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

  • Heat Sink SSR Solid State Relay for Temperature Controller Accessories 40A

https://www.amazon.ca/dp/B06WLNHPWK?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

  • Bimetal Temperature Control Switch Thermostat 75℃
    N.C KSD9700
    Chose higher temperature if you print chamber need to be over 60℃. Chose a sensor 15℃
    more of the max chamber temperature needed

https://www.amazon.ca/dp/B00978Q7S0?ref=ppx_yo2ov_dt_b_fed_asin_title

  • NTC Thermistor 100K, NTC 3950 100K ohm Thermistor Temp Sensor

https://www.amazon.ca/dp/B0714MR5BC?ref=ppx_yo2ov_dt_b_fed_asin_title

  • Fuse Holder Inline Screw Type + 100 PCS Fast Blow Glass Fuses Assortment
    Chose the right fuse for your voltage and heater wattage
    How to calculate fuse needed Ex: 400w / 115v = 3.5 amp so i chose a 4 amp fuse

https://www.aliexpress.com/item/1005007078035872.html?spm=a2g0o.productlist.main.13.5dfa4df79qWhYf&algo_pvid=0fd9c9f0-8c0f-47ac-9134-9c9fd28df3ec&algo_exp_id=0fd9c9f0-8c0f-47ac-9134-9c9fd28df3ec-6&pdp_ext_f=%7B%22order%22%3A%221138%22%2C%22eval%22%3A%221%22%7D&pdp_npi=4%40dis%21CAD%2111.20%215.13%21%21%2155.26%2125.31%21%40%2112000039327205970%21sea%21CA%21121095306%21X&curPageLogUid=QWT6xmF9gqin&utparam-url=scene%3Asearch%7Cquery_from%3A

  • You will also need wire make sure to use the right gauge wire
    14-16 gauge is a good start
  • How to wire the heater: Check the picture
  • Make sure you adjust the pin layout to your needs
  • For klipper to SAVE_CONFIG after PID_CALIBRATE_CHAMBER_HEATER the [heater_generic chamber_heater] section need to be in printer.cfg file
  • In Orca Slicer you will need to chose Chamber temperature and enable Activate temperature control. For other slicer i dont know i only use Orca
  • This tutorial doest not tell you to place the heater in the chamber. Make sure you chose a good location

Tagi