1 / 10
Subaru Overhead Ham Radio Mount (Icom 2730A) — zdjęcie 1
1 / 10

Subaru Overhead Ham Radio Mount (Icom 2730A)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Subaru Overhead Ham Radio Mount (Icom 2730A)Vehicles It Fits:Outback 2015-2017Forester: 2014-2016WARNING: I am not…

Ocena
0 / 5
Polubienia
21
Pobrania
57
Wydruki
0
Wyświetlenia
1418
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Ideas
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Subaru Overhead Ham Radio Mount (Icom 2730A)

Vehicles It Fits:

  • Outback 2015-2017 Possibly 2018 and 2019 as well. 
  • Forester: 2014-2016

WARNING: I am not responsible for any damage to your vehicle. This project will permanently alter your overhead console. It should also be noted that this is still a work in progress, and the design may be updated in the future.

Filiment Choices

  • ASA (Recommended Choice)
  • ABS (Okay but no UV Resistance)
  • PETG (Will work in colder Climates. Not Recommended)
  • PLA (Not Recommended)

Parts Needed:

Tools Needed:

  • Soldering Iron (For Heat Inserts)
  • Drill Bits
  • Drill
  • Philips and or hex drivers

Instructions:

  1. After printing all parts, take the main body, place the Icoms mounting bracket in the middle, and secure it with the x4 M3 bolts and nuts on the other side. (If you don't have the magnets installed on your 2730A, then you will need to install them.)
  2. Then take the radio's head and insert it to ensure fitment. It should snap in place and not be able to be shaken free. Because this print requires fitments, your printer's calibration may need to be fixed. If it is too tight, then you can try to scale up the part slightly.
  3. Now you can take your overhead console from the car and remove it by pulling down. There will be a few plugs you have to remove.
  4. Then you can carefully pry out the sun glass door from the side. It should pop out. Then remove the rubber bump spot and the gear on the side by two screws. After that you should be left with a clean cubby.
  5. Insert the main body to ensure it fits well. Note the side that the square hole is on and drill a hole large enough to pass through the RJ12 communication wire through the overhead consoles housing behind the square cut out.
  6. Take the main body out and insert one of the legs to the proper side where they fit. Then take a marker and mark the screw holes. Do this for both legs.
  7. Now drill a hole slightly larger than the bolt needed where you marked on the console.
  8. You can now insert the x8 heat inserts into the project. x4 should go into the back of the main body, and the other x4 should go into the legs. x2 for each leg.(Better to put them on the inside of the legs so they can't be pulled out)
  9. Now you can take x4 M4 bolts and attach the legs to the main body.
  10. Now insert the assembly into the overhead consoles cubby and use the other x4 M4 bolts to screw from the sides into the heat inserts on the legs through the holes you drilled. These holes may need to be drilled out at a bigger size if your holes are off at all.
  11. Assuming you have run your communication wire up the A-Piller and over to the overhead console, you can now take the overhead console and feed the wire through the square hole as you reinstall the console into the ceiling.
  12. Now that the overhead console is reinstalled in the car, you can plug in the radio's head and push it in place. It should snap in place with the magnets.

Overhead Mic Mount

  • If you want the mic to hang from the ceiling, I have included a small printable hook. This hook is made to be inserted between the console and the ceiling. It has a small slit on the bottom that can be pushed into the raised line on the overhead console on the 2016 outback. If this line is not present on your model, then you don't need to worry. Simply pushing this hook between the console and the ceiling will often hold it in place very well.
  • At a later date, I will be updating this project to include a plate to add an RJ12 plug in the dash to allow for a remote mic location.

Resale of this model for profit is restricted.

Print Settings

Printer Brand:

Bambu Lab

Printer:

Bambu P1S

Rafts:

Doesn't Matter

Supports:

Yes

Infill:

At Lest 15

Filament: Polymaker ASA BlackExtra Info

Optional Radio Installation

If you want to copy my radio install, then I will include that information here.

  1. I started by removing the driver's seat and inserting a small piece of plywood under the carpet under the seat.
  2. I then placed the radios factory mount on the carpet that's over the wood and screwed it through the carpet into the wood below.
  3. I was then able to bolt the radio in with the pl259 connector and audio ports facing the rear seats.
  4. I ran the antenna wire under the carpet in the rear passengers' foot well and then up the side of the back passenger seat into the pillar near the triangle window in the trunk. I then ran it into the ceiling and out the top of the back hatch and out to a NMO connector on a L bracket attached to my roof rack.
  5. After running the antenna wire, I ran the RJ12 cable for the radio head under the carpet in the driver's foot well and up the bottom of the dash and into the A-Piller. After getting to the top of the window, I moved across the window and dropped back down into the spot where the overhead console is normally mounted.
  6. I attached a small speaker on the pillar where the seat belt is attached so it would be near my ears and ran the wire through the plastics down to the radio.
  7. I also ran power from a small relay board I have under the hood attached to an auxbeam controller. (Had to drill a small hole in the firewall. Located high in the passenger wheel well.)
  8. At this point the unit is operational. If you want to get better signal, then you will need to ground all your doors to the main chassis. This can be done with a roll of small grounding strap, some ring connectors, and a set of small serrated washers.
  9. Go to the door jam of each door and remove one of the bolts on the door side. Put a serrated washer and then the ring connector with the grounding strap crimped to it. Then retighten the bolt and with the door fully open run the strap to the bolts on the other side of the door hinge and repeat. Repeat this for all 4 doors and both the hood and the back hatch. You should also run a ground to the bracket that the antenna is mounted to. This will greatly help with the RF noise that the subarus puts out.

Category: 3D Printing

Tagi