VITALPET : dog identification and recall / training collar
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
a dog recall and training collar
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 10
- Wydruki
- 0
- Wyświetlenia
- 165
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Pets
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
VITALPET
A dog recall and training collar that uses an Arduino Nano and 3D printing.
Caution: Amateur-level soldering and electronics skills are required. There is a significant risk of burns if you don't know how to use a soldering iron. Supervision by a responsible and competent adult is essential for minors.
Filament 3D printer :
- Filament ASA prusa 750gr https://www.prusa3d.com/fr/produit/fillamentum-asa-white-aluminium-750g/
Electronic components:
- Arduino Nano ESP32 https://store.arduino.cc/en-pl/products/nano-esp32 or https://amzn.to/44NYKb8
- Wire electronic : https://amzn.to/42sgzLw
- Screen OLED 0.93p IIC https://amzn.to/4jsGxEQ
- Remote RF + modul 433MHZ or 315 Mhz : https://amzn.to/3YgSSDz or https://amzn.to/4lIYuk5
- module Step Up CN6009 VIN 3.7volt to VOUT 5Volt or 5.5Volt https://amzn.to/3YOM7ZH
- module TP4056 USB-C ( important for the modele print ) https://amzn.to/42XThNL
- switch ON/OFF YW4-104 6pin 7mm x 7mm https://amzn.to/4cTvKRw
- battery 3.7V minimum 1000mAh ( i have MakerFocus ) https://amzn.to/3Ydh1uD
- buzzer 5V 2pins https://amzn.to/4iAx5xY
- resistance 1 Kohm https://amzn.to/3GpAtOy
- transistor NPN 2n2222 https://amzn.to/4jpZ04C
- collar dog ( option ) https://amzn.to/3RzVIzB
- Glue for ABS https://amzn.to/44Fqmzc
Must-Have Accessory if you already have, no need to buy :
Soldering Iron Pine64 18w-88w https://amzn.to/3GlXrpN
soldering wire 0.8mm without Plomb https://amzn.to/3YMVKYQ
carpet soldering 500 C : https://amzn.to/3Gs7c5V
cutting pliers : https://amzn.to/3RCKudI or https://amzn.to/449PoXd
Kit Clean Soldering : https://amzn.to/4joNG8R
Tips for printing parts :
- ASA filament : shock resistant, as well as ABS and resists the heat of the STEP UP module better
- 0.2mm 15% infill
- nozzle 0.40mm
- bed texture
- temperature Default Prusa filament ASA in prusaSlicer ( 260 C ) Bed ( 105-110 C )
- supports : Full ( important for screen and for collar )
Open the file
To upload the . ino file to your arduino nano esp32 you need to use the arduino IDE software. Here is the manufacturer's link for a guide.
https://support.arduino.cc/hc/en-us/articles/4733418441116-Upload-a-sketch-in-Arduino-IDE
Once you've uploaded the ino file to the Arduino Nano ESP32, you can solder the cables as shown in the diagram below.
Caution: NEVER touch the battery with the soldering iron. There is a risk of serious injury, even explosion and burns.

Here is a description of the pins to connect together :
| Screen OLED 0.96 ICC | Arduino Nano Esp32 |
| SCL | A5 |
| SDA | A4 |
| VCC 3.3V | 3.3V pin |
| GND | GND |
| Remote RF + modul 433MHZ or 315 Mhz | Arduino Nano Esp32 |
| D0 | D3 |
| Buzzer 5V | |
| Resistance 1Kohm | D2 |
Caution For transistor NPN 2N2222 :
3 pins : Emisor - Base - Colector
Base : is connected to the resistor, and the resistor will have the other end on pin D2 of the Arduino
Emisor : is connected via a cable to the negative pole of the Step UP module, therefore its output VOUT
Clector : is connected to the negative pole of the buzzer
Caution Step UP CN6009
check with a multimètre that OUT + / - give 5 Volt, better 5.5Volt MAXIMUM for the module RF, the buzzer, and arduino nano esp32 ( VIN pin on arduino can take 5V ) .
on the module, connect the "IN - " wires to the GND (OUT - ) of the TP4056 module
connect the “IN + ” wires to the OUT + of the TP4065 module
CAUTION : don't forget push OFF the switch
on TP4065 module connected pin B+ to switch ON/OFF YW4-104 ( another pin to switch can go to wire + to battery ) , and put wire - battery to the module TP4065 , pin B- .
CAUTION !!! Before push ON switch, Check the diagram and your connection to be sure that you do not produce a short circuit, this can damage your modules.
| a version of the project with more option like BLE-NOW, real-time heart rate and ECG monitoring, temperature, GPS with precise orientation , real-time tracking, and web server (free and 100% confidential) is already under development. It is currently being tested and improved graphically. |