1 / 10
VITALPET : dog identification and recall / training collar — image 1
1 / 10

VITALPET : dog identification and recall / training collar

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

a dog recall and training collar

Rating
0 / 5
Likes
5
Downloads
10
Makes
0
Views
165
Reviews
0

Updated at source:

Model information

Category
Pets
License
Creative Commons — Attribution — Noncommercial — NoDerivatives

VITALPET

 

A dog recall and training collar that uses an Arduino Nano and 3D printing.

 

Caution: Amateur-level soldering and electronics skills are required. There is a significant risk of burns if you don't know how to use a soldering iron. Supervision by a responsible and competent adult is essential for minors.

 

 

 

Filament 3D printer : 

Electronic components:

 

 

 
Must-Have Accessory if you already have, no need to buy  : 

Soldering Iron Pine64 18w-88w https://amzn.to/3GlXrpN 

soldering wire 0.8mm without Plomb https://amzn.to/3YMVKYQ

carpet soldering 500 C : https://amzn.to/3Gs7c5V

cutting pliers : https://amzn.to/3RCKudI  or https://amzn.to/449PoXd

Kit Clean Soldering : https://amzn.to/4joNG8R

 

 

Tips for printing parts  :

  • ASA filament : shock resistant, as well as ABS and resists the heat of the STEP UP module better
  • 0.2mm 15% infill 
  • nozzle 0.40mm
  • bed texture
  • temperature  Default Prusa filament ASA in prusaSlicer ( 260 C ) Bed ( 105-110 C )
  • supports : Full  ( important for screen  and for collar )  

 

Open the file 

To upload the . ino file to your arduino nano esp32 you need to use the arduino IDE software. Here is the manufacturer's link for a guide.

https://support.arduino.cc/hc/en-us/articles/4733418441116-Upload-a-sketch-in-Arduino-IDE

 

Once you've uploaded the ino file to the Arduino Nano ESP32, you can solder the cables as shown in the diagram below.

Caution: NEVER touch the battery with the soldering iron. There is a risk of serious injury, even explosion and burns.

 

 

Here is a description of the pins to connect together : 

Screen OLED 0.96 ICCArduino Nano Esp32
SCLA5
SDAA4
VCC 3.3V3.3V pin
GNDGND
Remote RF +  modul 433MHZ or 315 MhzArduino Nano Esp32
D0D3
Buzzer 5V 
Resistance 1Kohm D2

 

Caution For transistor NPN 2N2222 :  

3 pins :   Emisor -  Base - Colector

Base : is connected to the resistor, and the resistor will have the other end on pin D2 of the Arduino

Emisor : is connected via a cable to the negative pole of the Step UP module, therefore its output VOUT

Clector : is connected to the negative pole of the buzzer

 

Caution Step UP CN6009 

check with a multimètre that OUT + / - give 5 Volt,  better 5.5Volt MAXIMUM for the module RF,  the buzzer, and arduino nano esp32 ( VIN pin on arduino can take 5V ) . 

 

on the module, connect the "IN - " wires to the GND (OUT - ) of the TP4056 module

connect the “IN + ” wires to the OUT + of the TP4065 module 

 

CAUTION :  don't forget push OFF the switch 

on TP4065 module connected  pin B+ to switch ON/OFF YW4-104 ( another pin to switch can go to wire + to battery ) , and put wire - battery to the module TP4065  , pin B- .

 

CAUTION  !!! Before push ON switch,  Check the diagram and your connection to be sure that you do not produce a short circuit, this can damage your modules.

 

 

a version of the project with more option like  BLE-NOW, real-time heart rate and ECG monitoring, temperature, GPS with precise orientation , real-time tracking, and web server (free and 100% confidential) is already under development. It is currently being tested and improved graphically.

Tags