Counting matching models…
All printable parts for your Original Prusa i3 MK3S+ Sorted by kit assembly manual chapters. You can use the file list and folder structure here to prepare parts in the same order as you will need them according to the guide. Attention,…
https://www.traiva-shop.cz/p/automaticky-hasici-system-proteng-500#34010
Filament : Prusament petg. PETG 0.20mm. 15% Infill : Gyroid. Nozzle : 230c. Bed : 85c. Support : None. Enable Ironining. All top.
The ASA printed parts I received from Slice Engineering, with the Prusa I3 MK3S+ Mosquito Upgrade kit, are slightly different from the original parts, as designed by WickedTwister. The rectangular opening, just above the heater block,…
I recently purchased the Mosquito for Prusa MK3S+ upgrade kit from Slice Engineering, that comes with the ASA printed extruder parts. On my previous setup, I've been quite pleased with the Delta-P print fan duct and wanted to use it with…
A simple case to mount a Raspberry Pi Model 4 B onto the frame of the MK3S using the existing, unused, M3 screw holes. Some clips to route the USB power cable along the rear of the frame upper arm, out of sight. It's a simple, clean and…
Since the temperature in my garage does not allow for 3D printing in very cold conditions, I built a polycarbonate enclosure. This enclosure allows me to store my Prusa MK3 (protected from dust) and to carry out prints in a warm…
Simple nozzle holder for Prusa MK3s, which you can put on the top of the printer. It can be printed without support.
I made a drawing, and it is an exact replica of the cable clip that comes with the Prusa MK3.5. After reviewing the manuals, I understand that all the new models use it (MK3.5, MK3.9, and MK4, along with their S versions) since they share…
Z-Axis Top Mount: Longer version to use on the left side with the servo attached. Extruder Cover: Optimized to use with 4mm OD, 2.5mm ID PTFE tube.
Hi there! This time I bring you a easy two armed light upgrade for your 3D printer. The file consists of 4 main part Arm seperated to 2 smaller part Holder and arm - could be printed as one for better load-bearing capacity Connector for…
Found this GCODE a few years back and found it very useful for cleaning/lubricating my smooth rods. Demo: I use this stuff: https://www.amazon.com/Super-Lube-21030-Synthetic-Grease/dp/B000XBH9HI/ Blurred out in pic as I'm not advertising…
I modified the object after printing to fit a distanced rasPi because I bought the version whit all pin
Voron StealthBurner has no filament sensor, let's add one. In case you have a MK3S's filament sensor retired or spare, we can use it to make a filament sensor for stealthburner. Voron stealthburner…
All parts printed in PETG accept the Light lens. Light lens was printed in PLA. I added the light lens to protect the LED strip. Light bar works well for my needs. Its a simple yet effective design for the older MK3S+ printers. Thank you…
Inspired by the need to print something 213mm tall on a printer with max height 210mm, annoyed by the fact that there is clearly a large gap between the lower mounts of the Z-axis and the toolhead, and frustrated that this upload would…
What is Galileo2 : it's a open source extruder https://github.com/JaredC01/Galileo2 What is a PRUSA MK3S+ IR filament sensor? What is MK3S+ IR filament sensor? you can get one from your old retired MK3S+ printer, or buy one for about $6,…
This design mounts the BIGTREETECH ADXL345 2.0 accelerometer board to the bed of the MK3S+ or any bed that is under 5mm thick. This design uses 4-40 screws that screw directly into the 3d print.
This design replaces the extruder idler with one that has mounts for the BIGTREETECH ADXL345 2.0 accelerometer board. It is not a full-time replacement and is only intended to be used during input shaping calibration. You must reinstall…
First, I mounted the ESP32 camera on the printer using the “MK3S+ ESP32 Cam Camera Mount” by @detlassnake_289499. After being dissatisfied for a long time, I wanted to mount the camera on my PLATSA enclosure, so I developed the base plate…
The Light Bar has now Printed Endcaps. The Diffuser is Printed in White or Clear PETG and clips into the Light Bar. Since the Printz of the Diffuser sometimes is just one or two Layer make sure you use dry and well tuned PETG to work.…
5020 fan upgrade for mk3s bear (Bondtech Extruder) .I printed parts with sla high temp material, for best look and resistance. Can be printed in PETG or PA variants. M3x5 4pcs. M3x10 2pcs. M3 nut 1pc. Fan i decided to solder on a 3 pin…
So I may have made the mistake of overtightening the print head fan screws (again). Rather than replace the whole fan, which is otherwise in perfect condition, I figured a couple of little "shrouds" to go over the cracked mounting holes…
A filament guide for Prusa MK3S printers where you can put the spool next to the printer, and not on the top. It is an easy print, just use the gcode or the STL. Only requires a 625zz bearing and an M4 or M5 bolt. The M4 bolt threads in…
Printed with maxed out walls for myself and has held up great
This is a remix between two models, print at 20% infill with supports for the flat overhangs.
When printing, hexagons don't need any supports however the semicircular bridge should be supported.
I remixed the arm to attach to an adapter that spins and holds the camera
I recently upgraded my MK3S+ with an MMU3 only to find that I had rather frequent issues with the MMU3 not being able to feed filament into the extruder. The filament would snag onto something inside the pneumatic fitting and just...not…
Raspberry Pi 3 B+ screwless case (snaps shut) with built in mount for Prusa MK3. It leaves the Raspberry Pi's ports fully accesible and hides it away behind the frame. Be sure to check the credits of this remix, which would not exist if…
Update: Electric Trigger Parts you need to buy on amazon: Relay board, 5v power supply, wire, misc connectors, and male to female bread board jumpers. The other stuff you should have got with the orginal Loop electric. I used these:…
I just added a couple of pieces and cut them at an angle. I also reversed the slots for my use scenario. Thanks to the original author for including the fusion file, which I also include. Enjoy!
Needed a mount for WYZE Cam V4. this one fit the bill. my first remix. I hope you like it.
Fan shroud that can be mounted onto Delta P Extruder cover. One shroud is for extruder without sock and 1.5mm lower one is for extruder with sock. I am using dragon hotend with my mod for extruder cover but outside is the same for both.…
This upgraded X-axis motor mount is part of the unofficial “MK2.9S” evolution of the Prusa MK2 platform, bringing modern adjustability and improved belt management inspired by the MK3S+ design. The mount replaces the original…
English I created this shell geometry of the Prusa MK3S+ to check in CAD whether the printer fits into a cabinet and how much space is available around it. The model represents the exact outer dimensions without any clearance and is ideal…
I wanted to try using input shaper with Klipper on my Prusa MK3S, so I needed to mount the ADXL345 accelerometer on heated bed. I designed a mount that allows you to install it near the belt mount. BOM: - x2 M3 threaded inserts (4mm long…
Fully 3D printable spool holder acting as a universal adapter. It allows the use of the USS Drybox and the original spool holder system from the new Prusa Core One+ / L on Prusa MK series printers (MK3S+, MK4). An ideal solution for…
Prusa i3 MK2.5S/MK3S X carriage with M3 heat set inserts based on original R7 stl. This model made for heat set inserts like in Voron Sourcing guides - M3x5x4 (https://aliexpress.ru/item/4000232858343.html or the same from another…
Tightly-fit dust cover for Z-axis motor on Prusa I3 MK3S, does not interfere with lead screws. Requires top z-axis mount removal. Also need to temporarily remove two screws through plate metal frame (they hold power supply in place)…
This is a remix from SubSite's excellent design , adapting it to the aluminum extrusions on the mk3. The shape lets you tuck filament strands in and keeps them from jumping out. It does a great job keeping my printing space clean. It is a…
I didn't like any of the existing MK3S-mounted dryboxes so I designed my own - fully printed and less ugly. You can optionally connect a 4mm PTFE tube for to protect the filament between drybox and extruder. For MK3S+, I recommend my…
Modified Prusa i3 MK3S fs-cover for filament filtering. Cut a piece of foam of apx. 10x10x10 mm and pinch a hole through it before inserting into the slot. Print Settings Printer Brand: MK3 Printer: Prusa i3 Rafts: Doesn't Matter…
Attention: In order to print the model on the Prusa MK3S, the object must be split in the middle in the PrusaSlicer. Front panel for prusa mk3s+ and 5 inch Waveshare DSI touch display (800x480 pixels). To complete the model will need the…
Tuned profile for printing with Fiberflex 40D filament. Optimized for use with supports, HQ surface finish and multiple parts printed at once. Out of the box, you get a little bit of stringing, and also great finish and flat seams. Below…
Alternative fan shroud for MK3S+ direct replacement Feel free to share and comment so design can be improved. Newer version: MK3SP_alternative_fan_shroud_V4_1 Hardware needed: 3 x M3x10mm bolt 2 x M3x20mm bolt 2 x M3 hex nut or 1 x M3…
This should be printed in PLA. The blade should have at least 20 percent infill. You can join the blade to the hilt using hot glue or other adhesion methods. Recommended printer - Prusa I3 mk3s
Inspired by https://www.thingiverse.com/thing:2843889 I used the one linked above for the Pi3, but needed an upgrade for Pi4 and decided to use a noctua 40x10 fan, as the new raspberry runs a little hotter. This can be mounted on any side…
I recently added a second fan using this dual fan mount , but the camera mounting arm that I previously had sat too close to the fans and would bump into it. So, I made a little cutout and extended it a tiny bit. I printed mine with 40%…
This model allows you to create new z-axis top parts that also supports a led lamp. The amazon reference is: https://www.amazon.it/dp/B09VGMFH2Y?psc=1&ref=ppx_yo2ov_dt_b_product_details The model improves also the holes for the bars to…
This simple part let's you screw in an M5 Eyebolt and attach it to the top of your MK3S+ to neatly guide filament without the spool being pulled of to the side or up by the hotend as well as the filament getting thrown of from the spool…
Modification of the "short_mount_bottom.stl" to avoid issues with Z-axis calibration. Also works on MK4.
Mount consists of two parts. One is modified Prusa extruder_cover R5. Two side holders with the Prusa size nut were added. This part you need to replace on your printer. It does not influent the standard functionality, the holders do not…
Update 1.0: - Object height offset - Base modification [EN]: This system allows you to clean your nozzle automatically every time you print ! Print parameter: - PETG - 0.20mm - 20% fill rate - No support Software modification: 💡Gcode…
Additional cooler for Prusa MK3S in more Prusa farm style. It fits a 40mm fan which can be connected to the 5V header on the motherboard. You can hold the fan behind the PINDA cable. It can of course be routed through the sleeve (which I…
The inner and outer screws and the base are shortend by 35mm. Otherwise it is the original model. By this, the model can easily be printed on a Prusa MK3S+ printer. Not much contribution from my sight but I though I could spare other…
I was having problems getting my filament sensor to trigger consistently on filaments that ran a little thin (1.72mm) in spots, and after recalibrating repeatedly, I noticed that my filament sensor holder was leaning slightly to the left.…
Post it holder which fits in the hexagon of the top of the z-axis.
A hole is added to have an extruder visualization. Stack some Neodym Magents Ø 8 x 3 mm and you are ready to go. Add a noctua fan from the prusa shop https://dkiracing.eu/de/prusa/664-hotend-fan-noctua.html and you are good to go.…
DO NOT TRY TO PRINT THIS WITH PLA SINCE IT WILL MELT!! If you have ABS at your disposal: use that. Otherwise PETG will do for prints below 80°C bed temp. This remix adjusts the form to fit the angular Y-Carriage on the MK3S, adjusts…
With balljoint for adjustability. Case fits a GXIVISION IMX298 USB Webcam but can be redesigned.
Modified from the latest heatbed cover (top) from Prusa. place a 6 inch (or so) filament (with some curve to it) into the small hole in the part, then slide the filament into the wire bundle and attach the top to the heatbed. I did this…
Remix des Models von grooveup um den Halter seitlich am Tukkari Gehäuse TF Acrylic zu befestigen
Printable spool holder for Original Prusa MK3S+/MK3 Warning: This spool holder is not compatible with Original Prusa MK4
Use M4x12mm (or shorter) self tapping screws to mount the smoke detector to this holder piece. After printing and mounting test that it does not block the XYZ calibration!
The original MK3S+ FS Cover for IR Filament Sensor with Duel LED has been modified to accept an M5x5.8 threaded insert.
Hey there, I added only a Ring for easy Rotation, so lets all rotate a looooooooot :) as well I extruded the inner Surface (Height) from the original 6mm, to new 5mm, otherwise the added Ring as well as the rotating Finger is touching the…
Idler mit kleinen Verbesserungen, da bei mir der Filamentwechsel nicht 100%ig sauber lief. Als Ursache hierfür konnte ich den orginalen Idler ausmachen, da in der oberen Lagerung durch die Bewegung das Loch aufgeweitet war. V1 Um dieses…
Remixed the original to support a 2kg spool of Prusament. You still need 2 608 bearings.
When spacers are used to shim the IR filament sensor, original fs-cover no longer fits. I fixed this by making the slot bigger. I printed mine on the MK3S from Filament PM PLA+ with 0.20mm SPEED profile in PrusaSlicer, but since the…
This is to cover your LCD on a Prusa i3 MK3S+. Whether you're doing a print overnight, don't like the light, or want to protect it, this is what should work. I also have the g-code file I used to make a PLA version (my print is in the…
2 verzie dlhší a kratší Kratší vznikol preto, aby ho bolo možné vytlačiť na MK3S. Je aj prepracovanejší a dá sa povedať, že aj dokončený. Dlhú verziu som už ďalej neladil, dávam ju ale sem, ak by sa niekomu hodila. Pre 2x AC/DC 24V 6A…
The original https://www.prusaprinters.org/prints/35611-prusa-i3-mk3s-hemera-upgrade-30 is great. But I found few uncomfortable issues so I fixed it! Improvements: PINDA mount. Extruder mounting system is horizontal instead of vertical.…
Revist on the original design, I needed it a bit lower.
Thats pretty much all, Printed on normal PLA, no supports no nothing, A fast and stylish print, No magnet or other parts needed, snaps in place! Should fit all the prusa printers with an exposed extruder shaft of 5mm (MK3S/MK3 Plus and…
A LED support for Prusa MK3S+ it was design to hold a LED Projector from IKEA.
Introduction The Prusa MK3S+ is a great printer but very slow. That's why I decided to develop an upgrade, something that hasn't been done before. This Upgrade kit allows you to make the Prusa MK4S look slow while maintaining the…
IF YOU KNOW THAT THESE WORK WITH OTHER PRINTERS, PLEASE COMMENT AND I WILL UPDATE THE DESCRIPTION! Noise and vibration damper feet for your Prusa that install just like those silly little rubber ones in the kits! These bad-boys will…
All credit to Zbigniew Trzepizur. This remix supports 40 mm pin headers (instead of 37.8mm) and uses 16 mm M3 (M3x16) screws instead of 14 mm. uxcell 40 mm pin header: https://www.amazon.com/dp/B07DXQ1K4B/ There are two plastic shrouds on…
Nemohl jsem nikde najít originál nožičku od Průši, tak jsem si ji vymodeloval. A je dokonce lepší jak ta originální. 😂 Oranžová je Průša, stříbrná je můj model, ale to asi každý pochopil. 🙂 Perimetry: 4 (možná by stačily 3) Výplň: 25 %…
I created a model of a bearing lubricant. (LM10UU). It is now possible to lubricate bearings on MK3 / MK3s + without dismantling the bearings themselves. -Variation1 is intended for a tube supplied with a printer from Prusa research…
Weil ich das Projekt unbeabsichigt gelöscht hatte, mußte ich es gerade alles noch einmal neu machen. Entschuldigung dafür. Dadurch fällt leider das bisherige Update Log weg. DIESES PROJEKT IST NOCH IM AUFBAU UND ES SOLLTE MIT DEM BAU NOCH…
A camera mount that works on both sides of the heatbed the camera Housing is from here: https://www.thingiverse.com/thing:2352964
UK: Recycling PRUSA MK4 cooler and AYF Fan for a new one: AYF MK3.5 • MK3S • MK3 recycling Fan. PRUSA MK4 The PRUSA MK4 is a popular 3D printer known for its reliability and user-friendliness. It is designed for both hobbyists and…
This is a very sturdy mount for the KUSBA 2.4 accelerometer for the prusa mk3s+, to help tune input shaping with klipper. Requires you to heat insert 2 standard M3 nuts. Until they are just flush with the surface, can be done with a…
https://www.traiva-shop.cz/p/automaticky-hasici-system-proteng-500#34010
Status: Finished! Working great! Status: 3-4-2019 Printing out all the necesarry parts, everything fit nicely! Waiting for the parts from china. Status 14-4-2019 Except for the filament sensor, everything arrived. Assembled the whole…
I'm working on an upgrade for my Anet AM8 printer. Owning a Prusa MK3S printing I loved the extruder. I wanted the same thing on my AM8. The only thing was that my AM8 printer works with a BL-touch sensor and not with a PINDA sensor. So…
I liked vladv's layout (https://www.prusaprinters.org/prints/49434-mk3s-filament-cover-with-ptfe-fitting/comments) but wanted to make a new one with a simple, printable layout that allow me to use my PTFEs and that will make it easier for…
The following parts are required for assembly: 1x M4x10 countersunk screw 1x M3x10 countersunk screw 1x M3 nut (forMK3.5 Tubeholder_Bottom) 1x M4 threaded insert (for MK3.5 Tubeholder_Bottom)…
P-110-MINI-MK3S-style-extruder remixed with a mount for a cable chain on the X-Carriage. The other parts for the extruder can be found in the original post The cable chains can be found on djkirkendall's post
A simple light bar that rests on the top of the z end stops, I used some cheap Christmas led stick on strips and a buck converter to power from the power supply! It wont fit on a mk3 bed sadly, i had to print it on my anycubic chiron!! Ok…
Printed in PLA using my MK3S+, would recommend using organic supports if possible, or not very dense because they can be a hassle to get out.
First layer calibration GCODE for Prusa printers, as implemented in Prusa MK3/MK3S firmware ( https://github.com/prusa3d/Prusa-Firmware ), originally created by Marek Bel. Enclosed GCODE files are generated directly by the firmware source…
IMPORTANT UPDATE Fixes implemented in this model, together with some other important updates, are now officially implemented in the Prusa R6 version, so please use them instead. This model remains here just for reference. Original…
Úprava původního dílu pro připojení PTFE trubičky na extruder, bez použití koncovky Festo Při první montáži spoje je vhodné vložit do trubičky vrták, aby se kompenzovalo případné zůžení průřezu trubičky viz ilustrační obr. Držák filamentu…
![Raspberry Pi Zero (2) W Mount for Original Prusa i3 MK3S+ [40 mm Pin Version]](https://media.printables.com/media/prints/1033873/images/7842630_b4fd99dd-678b-4857-9320-e5fb65ea80ba_cd3f3416-0d03-45f7-80dd-3c40e300b46e/40-mm.png)
![First Layer Calibration Pattern [from Prusa MK3/MK3S firmware]](https://media.printables.com/media/prints/104767/images/1049067_18c18458-fa9e-4654-902c-b1e97a049d27/4c891d12cf05afc76616116d7b423361_display_large_10.jpg)
