Voron Ascot aka Top hat. All the umbilical height in the right places. Now with updated front corner clips.
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
All business in the front and party in the back! and a cable bridge. Look for my G2E umbilical mods at Printables, too.
- Ocena
- 0 / 5
- Polubienia
- 20
- Pobrania
- 40
- Wydruki
- 0
- Wyświetlenia
- 904
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This is a top hat for a Voron Trident 300 that I'm calling an Ascot because of the jaunty angle ;-) . This gives extra height for an umbilical setup in the rear yet allows a complete unobstructed view into the chamber while standing in front of the printer. Also a modded BTT cable bridge and rear CAN cable clamps for the rear are included. I've used a 0.5 mm rod for the cable support but I may change it to a 0.64mm rod. Do test fit the panels for fit by bonding them with a drop or two of CA glue. Mine fit fine on two full print/builds. The stock acrylic lid can be reused. Print a mirror of the side panels for the other side and corner clips. The sides and rear panels all bond together. I used thick CA with accelerator for a fast job. The standard rolled 2mmx5mm foam tape can be used between the frame and the panels and new panels and the top plexi pane. The side and top clip screws for the plexiglass thread directly into the plastic holes. The 4 front edge screws screw into t-nuts or roll-in spring nuts. If I remember, I had to shave off/heat-and-push a few mm of the bottom outside corners of the rear panels where the groove shape extends over the vertical end extrusions. I just used an assortment of fasteners for attachment to the frame. The forward screw hole on the side front triangular panels do not use t-nuts. All other screws to the 2020 use t or spring roll-in nuts. I have revised the front corner clips. The entire Ascot does assemble and seal well. Don't over-tighten the screws so much that the plexi deforms into the foam tape to the point of cracking. Be careful.
This mod also works with the G2E extruder using a piano carbon steel rod bridge:
I printed the panel sides very light with 2 top and bottom layers, 3 wall loops and 15% infill. I printed the first copy as a proof-of-concept (and I'm using it), you may want to increase the amount of filament used. The clamping clips were printed @100% infill. With an added BentoBox https://www.printables.com/model/1279472-bentobox-platform-for-inverted-wiring-cabinet-in-v hepa/charcol filter along with the Siboor rear carbon filter there are zero odours while printing with my oldest stinkiest ABS. The chamber is well sealed.
The heat up top is not an issue with ASA or ABS filament. I require lower chamber temps for PETG. The heat is trapped up top and the filament can soak up too much heat up top and some transfering through the motor. I have made this ducting for the large cooling blower to draw cool air from outside the chamber and force the hotter chamber air outwards. It works very well. This clamps onto the blower, can be slid upwards and allow access to your inverted wiring cabinet. Once snapped into place, it can remain there for all printing. Just don't forget to remove the top 90 degree duct from the blower when printing PETG or PLA. You need the blower to fill the upper part of the chamber with cooler air. Print PLA and PETG with the door open.
You may also be interested in my other Voron Trident mods shown here or at https://www.printables.com/@JimChristian_3198049 . They work well :-)
Also, if you find value in this, please give it a like. Thanks.
