HDD Cover & USB-C charger for Thinkpad X230 X230i X230T X220 X220i X220T
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
I wanted to add USB-C charging to my Thinkpad x230T to make it more versatile. Print at 0.15mm with 100% infill
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 18
- Wydruki
- 0
- Wyświetlenia
- 530
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Portable Devices
- Licencja
- Creative Commons — Attribution — Noncommercial
I modified the cover to accept two different types of USB-C chargers to make my ThinkPad tablet PC more versatile.
I have also made a label for it as a .PDF on an A4 Page.
Quick Info:
This will only work or only make sense if you're not using the HDD bay or have dissembled your SSD to make it as short as possible or have an mSATA SSD in the WWAN slot of the Laptop.
What you need:
- 3mm LED's of various colors to your liking
- 550 Ohm 1/4W Resistor
- 500Ohm 1W resistor
- 3S LED Lithium battery indicator
- 3S 2A USB-C Lithium battery charger module,
- PD 100W USB C to ThinkPad adapter
- 0.35mm² wire for the USB PD to ThinkPad adapter
- 0.2mm² wire for the USB 3S battery charger and to solder the LED's, relay, button ect.
- 10SQ045 10A shotky diode, or similar (the lower the voltage drop the better)
- 1N4001 Diode as a protection diode for the relay
- a5wk 5V Relay
- Hot glue to secure everything (I know its not pretty but with the limited space its the easiest option)
- Heat shrink tubing
- (Optional XT30 or similar Connectors so you can remove the cover from the laptop)
Overview:
Looking at the image the Left USB-C is to charge the battery directly with a 10W/2A Li-Ion 3S USB-C charger module which is connected directly to the battery. This one doesn't require PD, QC or similar, just a 5V USB socket that can deliver about 2.4A. (Disclaimer: charging your laptop battery like this regularly may mess up the calibration and percentage indicator, I added this just in case I don't have a suitable PD charger available)
In the middle is just a 3S Li-ion battery indicator with the LED's and button wired to the front.
The one on the right is a USB-C PD to ThinkPad connector which I disassembled and modified to work in the ThinkPad while still being able to use the Original barrel charger.
All the modules and components are available on sites like Aliexpress.
Setup:
The 3S 2A Lithium battery charger and the 3S Battery indicator are just wired directly to the + and - Pins on the motherboard battery connector using 0.2mm² wire
In order to get the PD module to work you need to connect the ground from the output PD module with a 550Ohm resistor to the blue ID wire, otherwise the ThinkPad will not charge from it. The power and ID wires are just soldered onto the wires for the barrel jack with 0.35mm² wire.
If you're planning on still being able to use the original barrel charger you need to add a 10A shotky diode after the PD module ( I used a 10SQ045 shotky diode). In front of the diode you will also need to add a small relay that switches the 550ohm resistor from ground to the ID pin when the 20V from the USB-C are connected.
I used a a5wk Relay, a 1N4001 Diode as a protection diode and a 500hm 1W resistor to power the relay. (YOU ABSOLUTLEY NEED A PROTECTION DIODE ON A RELAY OR YOU RISK DESTROYING YOUR EQUIPMENT DUE TO THE BACK EMF FROM THE RELAY COIL)
This isolation between the two power sources is necessary because otherwise if you connect a normal ThinkPad charger the ID resistors are going to be switched parallel and this is going to cause Issues and the Laptop will no longer charge from the barrel jack.
You may need to modify the plastic in your case a bit because the wires could cause issues with the keyboard not sitting properly or collide with the stylus mechanism.
I removed all the SMD LED's and used 3mm LED's for all the indicators and wired them up to where they connect on the board. Same goes for the Button of the Battery indicator.
And finally a word of caution!:
I really recommend doing this only if you know what yore doing since messing with lithium batteries can be dangerous. Doing things wrong could damage your battery or laptop.
Feel free to comment if you have questions