Liczymy pasujące modele…
The Power Button of my wife's Lenovo Thinkpad T570 was broken and get's stuck in the case. So i decided to make a replacement. I printed the button from Nylon. To Repair the Button you have to do following steps. Remove the battery…
Print the two sides, insert screws. Screw under desk or on wall with the dock clamped between. You should be able to easily remove the dock if needed due too the brackets pivoting at the screw holes.
Thinkpad T480s bottom case Still alot of work to be done. Free free to modify to your needs. Print out of ABS or PETG at least...PLA WILL warp after a few days use.
This is AndBu's ThinkPad Dock desk mount with additional holes for attaching a bracket for a UGreen USB 4to2 hub. I've reversed engineered the design and added a floor with sockets for M4 nuts and top holes for M5 hex screws. I've also…
Best printed in TPU/Flex filament with 100% infill. If printed in TPU, it can be pushed into position without disassembling the notebook.
Turn your Pixel 8 into the ultimate webcam for your ThinkPad! This bracket was specifically designed to bridge the gap between the Lenovo ThinkPad L13 Yoga and the Google Pixel 8 . With the release of the native "Webcam" mode in Android,…
This is AndBu's ThinkPad Dock desk mount with additional holes for attaching a bracket for a UGreen USB 4to2 hub. I've reversed engineered the design and added a floor with sockets for M4 nuts and top holes for M5 hex screws. I've also…
An ultra realistic and almost exact clone of Lenovo Thinkpad T490s.
I have on old IBM Thinkpad laptop with missing battery. So, I decided to design my own DIY battery for it. I didn't have an original battery so all the information I gather from the Internet and measuring the place for the battery in the…
I had some locked Lenovo Thinkpad batteries that no longer work with a laptop, but the cells inside those batteries were in good condition. They all have roughly the same capacity after testing. So, I decided to give those cells another…
Two-piece snap-fit lid cover for ThinkPad X1 Yoga Gen 7 (14"). This model is split into left and right halves and installs by sliding each piece from the outer edges toward the center of the laptop lid. The side-wrapping structure…
This model is a heart-shaped replacement for the TrackPoint on Lenovo ThinkPads for modern ThinkPads. Ideally this print is printed with foaming TPU as this provides the best grip and doesn't risk damaging the screen when closed, but of…
Old speaker covers were uncleanable. I decided to rip them off and print replacement. I used PETG to print and glued it with double-sided tape
Thinkpad T480s bottom case Still alot of work to be done. Free free to modify to your needs. Print out of ABS or PETG at least...PLA WILL warp after a few days use.
Feet in order to keep your thinkpad E15 of the desk for improved cooling Printing Instructions: use the included .3mf file or import twice into your slicer and mirror one piece Installation: use some weak double sided tape to stick them…
Turn your Pixel 8 into the ultimate webcam for your ThinkPad! This bracket was specifically designed to bridge the gap between the Lenovo ThinkPad L13 Yoga and the Google Pixel 8 . With the release of the native "Webcam" mode in Android,…
If you want to put other objects than your fingers on the keyboard (in my example a different keyboard) you put this on top that will allow you to do exactly that! As a bonus i included a hole for your finger so you can still use the…
I had 2 of these mouse fail in the exact same way. The scroll wheel breaks before the first battery runs flat ! Properly unacceptable, trash quality. Still, I don't like to see these things go to waste. I designed an easy to print…
Lenovo Thinkpad T14 Castle Holder with Cable Tunnel. With a little tower on the left for Ethernet cable plug and cable hiding. Also with venting holes not to block cooling.
I loved this model, but I use the Slim Pen, so I wanted to adapt it to my needs. It works really great. Instead of a minisforum Stylus, I adapted this to work with the Slim Pen from Microsoft. Be sure to check your magnet orientation if…
The original model featured a hole for a C7 Type connector (The one with only two pins) on one side. Because mine had an plug of the C5 Type (looks like an cloverleaf) it woudnt fit. I edited it so it fits for my plug. For this remix i…
It protects smart card readers from dust. It can also be used as a residue-free alternative to stickers for identifying laptops (when printed in different colors). It's completely flush when inserted. This way it cannot get caught…
3D printed picture frame to hold my old Thinkpad Twist s230u to the wall as a Home Assistant dashboard (12.5" touch screen). I'm guessing that this is hard to replicate exactly, but could maybe serve as a source of inspiration for others.…
1:1 Model of a 24Wh battery for ThinkPad T470/80 T570/80 and T25. It locks in place securely, the mechanism on the left latch works as intended. I made it because I mostly use my laptop on a charger/docking station but didn't want a…
This is a battery clip for your old IBM thinkpads. I designed it for my 380XD however this will probably fit other IBM thinkpads of the same era.
A vertical stands for a Lenovo T-470S Needs 4x M4x12mm Counter sunk Screws https://cad.onshape.com/documents/12fb459e04ee54ef71417ee1/w/22e1f91618245641cb708e2b/e/74741ba472c6ee3843f78730?renderM
Small, elegant stand to use your laptop as a screen (with mouse and keyboard setup), to unclutter the desk and raise the screen to a proper level. Easy print, no supports, only 25 grams of filament. Stands stably with no flex. If you have…
A remix of the original with support for fixing the stands to a wood desk using 5mm screws sat flush diagonally.
Print in soft TPU at whatever layer height you want. Looks good at 0.1 or 0.2 or whatever. Print it solid with 4 walls. I stuck it on with smartphone 2 sided tape but you do you.
Wandhalterung für ein Lenovo Thinkpad L15. Es sind Aussparungen für die Schrauben, Lüftungen und Anschlüsse vorhanden. Die Halterung kann ohne Stützen oder Brim gedruckt werden. Viel Spaß euch :-) Print Settings Printer Brand: Anycubic…
Probably compatible with other Thinkpad models
If you like the model, please give a like 💟 and post your prints 📸. 💡 Underware - Multiboard - Lenovo 90W Power Adapter holder (ThinkPad Universal USB-C Dock) 💡 💫 Recommendations PLA/PETG 0,2 mm layer no support
If you like the model, please give a like 💟 and post your prints 📸. 💡 Underware - Multiboard - ThinkPad Universal USB-C Dock holder 💡 💫 Recommendations PLA/PETG 0,2 mm layer yes support - for the lip on the top that holds the dock in place
ThinkPad Dock Monitor Pole Mount Streamline your workspace by mounting your ThinkPad Dock to your monitor pole with ease! Just print and attach—no supports or brim needed. Perfect for docks with wall-mount inserts on the bottom. What…
I put indents in the original design for SD cards. Not sure about durability because of the indents but yolo
This is a reproduction model of a battery enclosure for the IBM ThinkPad 730T tablet computer. The inside is designed to accommodate 6 AAA-size NiMH cells and 3 terminals. If you'd like to see how I made the terminals, please watch the…
This is a reproduction of the top bezel of the IBM ThinkPad 730T Tablet computer. You can find more information in my restoration video below:
This is a reproduction of the PCMCIA door cover for the IBM ThinkPad 730T tablet computer. For video of the full restoration, please see below:
This is a reproduction of the original pen holder for the IBM ThinkPad 730T Tablet computer as well as a custom version. 730T_door_pen - this is the original model that has a lever to help eject the pen. This can be difficult to print so…
This is a vertical laptop stand. It's also called as necksaver:) It's designed for Thinkpad T480 but you can use for any laptop which has proper dimensions. The second version is designed to prevent falling etc. But the movement…
This is a smart card reader cover for thinkpads. It is designed for T480 but it should work on others too. To make it look perfect, sand with ~600 sandpaper. Height of thinner part: 1.25mm Height of thicker part : 1.5mm Print Settings…
I got a Lenovo Thinkpad X1. It has a flashing red LED on the lid. I immediately thought of two options... Bender or Terminator. Position the tip of the cigar exactly on top of the LED. ;-) Printed in PLA - the color changes are included…
Rough replacement for a 15" 4:3 T60 HDD cover. Surprisingly no one has made one of these yet, despite every other model of T60 and T61 having them made already. This is my first time making and uploading a 3d model, so forgive any…
The original cover didn't fit on my W510, I don't know if there are multiple styles of the HDD door, but I modified this one with a few simple cuts so that it fits on mine. Category: Computer
Remixed MartinD's Adapter design to fit USB-C cable of NOVOO USB C Docking Station (14-1)
this is an holder for a thinkpad dockingstation on your skadis pegboard. printsettings: filament: i used petg but you can use whatever you want support: its handy to use supports i did and it came out perfectly
About this: This is a Power adapter for ThinkPads that have the Hexagonal Power Plug on the back. According to https://www.thinkwiki.org/wiki/Power_Connector the following models are known to use this connector: ThinkPad 355, 355CS, 355C…
Based on the Lenovo Thinkpad workstation W530. It was scaled down by 1:5 except the hight which was scaled by 1:3 to allow for a more rigid hinge mechanism. Clip the display onto the base. Display then can be opened and closed and should…
Mades my first model since batteries for Thinkpad is expensive i made thin battery cover WORK IN PROGRESS MAY NOT FIT WELL Feel free to remix
Simple replacement feet for the Lenovo Thinkpad E14. Might fit on other models too.
2.5" Drive HDD / SSD Laptop Drive Caddy Disk Tray Bracket for Lenovo ThinkPad. Compatible Models: For Thinkpad T470 T480 T570, For Thinkpad P50 P51 P51S, For Thinkpad P70 P71 P72, For Thinkpad E460(NOT E470)， For Thinkpad E480 E485 R480,…
I need to stack some laptop chassis - and with the original feet, they tend to slant a bit to the front side. Since over the back feet the laptops are 17.75mm high, and over the front feet it's 14.5mm, I adjusted the height of the…
Laptop stand for the Lenovo Thinkpad Extreme X1 (Gen1) Allows for a thight fit but not so that anything gets damaged or scratched. Larger base to allow for stable stand with a lot of pheriphials attached Step included if you want to…
My (better, even though I say so myself) redesign of the Lenovo ThinkPad keyboard folding foot. Print with supports (only because of the holder pins) and also clean them up afterwards so they fit in well. Category: Computer
Remixed from Shabubus M3 Macbook Wallmount. Printed with PETG 5 walls/30% Gyroid Infill
This is a remix of 4sStylZ of a release by @pansono. I scaled up the width of the leg by 2.75% and added some parts that I'd call snappers. Why? Because with these, the leg folds back and forth with a satisfying snap, just like the…
Keep your drawings, measurements and to-do sticky note lists on your laptop's monitor. Why? Keeps one organized! Has a pocket for a stack of sticky notes. Detaches for transportation. Attaches magnetically to a laptop screen*. *So far…
A simple stand for the Lenovo Thinkpad P16S that integrates the Lenovo USB-C Dock (40AS) This print consists of 2 pieces, a top and bottom. The top is designed to slot into the bottom piece and with glue, it will hold beautifully. If the…
I use this power brick for a bunch of different things from powering my custom PSU to my Pinecil. Its a bit annoying with its long cables and I found that it just got in the way on the table. Since I made my multiboard I figured I could…
A vertical laptop stand to perfectly fit a Lenovo ThinkPad T14 Gen2. I needed to increase my desk space and this worked splendidly. No supports needed.
An help to stand up the Lenovo ThinkPad USB-C docking station - Inside dimensions → 81mm x 31mm - Outside dimensions → 120mm x 35mm I don't know if this works with every Lenovo ThinkPad USB-C docking station. I test it with the Gen2 Type…
Print 2 and slide onto each end of the hinge side of your laptop. I printed mine in Atomic PETG-CF.
This is an under desk mount for Lenovo ThinkPad Thunderbolt 3 Dock Gen 2. The mount requires 2 pairs of 3M velcro command strips to give a flush to the desk look. no support needed! I am using the large size command strip, but medium size…
Do you have a ThinkPad? Do you use headphones while working on your ThinkPad? Can you not be bothered with the irritation of having headphones around your neck? Then this attachment is for you This is a simple friction fit headphone…
This is a stand which lets you use your Lenovo ThinkPad T14s Gen 3 (2023) laptop lying on its right side, e.g. for gaming or watching video while lying down. It redirects the cooling vents out the back. The two small holes in the main…
0.25mm nozzle with support on build plate only recommend.
Remix'ed to fit the T530 which is slightly thicker on both top and bottom Print Settings Printer Brand: Creality Printer: Ender 3 Pro **Rafts:** Doesn't Matter Supports: No **Resolution:** 0.28 Infill: 20% **Filament:** - PLA but you…
For the original strift of the Helix 2, it is best to print it horizontally with the lowest resolution possible. y
Dubbed the “Lenovo Shoe” By experts (Me), this is a set of stands to allow for better airflow when you are using the Lenovo IdeaPad/ThinkPad on a deskmat or soft surface. Print 2, or extend the width of the stand and print one really long…
M.2 tray for Lenovo laptops. The design is optimized for fdm printing and does not require support.
This is a simple bracket for mounting the 135W Slim Lenovo Thinkpad charger, the hole spacing is compatible with Multiboard layout. Used some 9mm T-bolts to fix it to the pegboard holes. I printed it with 0.3mm layers and 0.4mm nozzle, 2…
This under-desk holder is designed for the Lenovo ThinkPad 20V 8.5A power brick, providing a secure and space-saving mounting solution. While primarily intended for under-desk installation, it can also be mounted on a wall. Each bracket…
The problem with the Surface Pro and other tablet based 2 in 1 PCs is that they aren't very nice to use in your lap. The rear kickstand/wobbly keyboard attachment etc make it unstable except on large hard surfaces. Microsofts absolutely…
I wanted a nice looking mount for my AirSpy R2 for my laptop, as I occasionally use SDR in my car and having wires all over makes it annoying. I printed mine in Overture PLA, but PETG may be better recommended if using outdoors in heat.…
A 45x45 thinkpad nub with a spot for an M5 nut. You'll need an M5 bolt cut to size to screw it through. Best printed in red PLA.
Mount your Lenovo ThinkPad Universal Thunderbolt 4 Dock to MultiBoard/Underware using Multiconnect Connectors! This model is uses the existing screw mounting holes and the inset edges in the Dock to lock the print to the Dock. It uses a…
ibm thinkpad 390 series hinge support you will need two m2.5x10mm and m2.5x16mm to attach the screen to the housing
If you're one of the 3 people left on Earth with a ThinkPad 500 from 1993 (my condolences), and the case plastics have broken due to the left screen hinge clutch, this part is for you. It straddles the hinge and serves as replacement…
I created this laptop stand for my Lenovo ThinkPad P16v Gen 2. It should hold other laptops as well, provided they are not higher than 26 mm.
I made this 3D printable ThinkPad UltraBay Cup Holder for my T430, however it’s going to fit any similar ThinkPad UltraBay. The model seen in the pictures may differ, I made this published version simpler to make it simpler for all to…
A simple but durable laptop stand for Lenovo ThinkPad laptops.
Problem: I want to organize my desk wires while also being able to take my laptop power supply (charger) on the go. Solution: This Lenovo 170W power supply holder can be mounted with adhesive or screws (drill holes as desired). There is…
I modified the cover to accept two different types of USB-C chargers to make my ThinkPad tablet PC more versatile. I have also made a label for it as a .PDF on an A4 Page. Quick Info: This will only work or only make sense if you're not…
Both feet of my Lenovo Thinkpad Keyboard 2 broke after a while so I took my calipers and designed new ones. They work identical to the original ones and even have the same satisfying click that might have made me brake the old ones. :P I…
IBM Thinkpad 600 Series Floppy Port Cover All ports have a tape underneath that secures the cover to the notebook case and allows the cover to open and close without getting lost. It is necessary to add this tape so that the cover stays…
IBM Thinkpad 600 Series Back Ports Covers All ports have a tape underneath that secures the cover to the notebook case and allows the cover to open and close without getting lost. It is necessary to add this tape so that the cover stays…
IBM Thinkpad 600 Series USB Port Cover All ports have a tape underneath that secures the cover to the notebook case and allows the cover to open and close without getting lost. It is necessary to add this tape so that the cover stays…
If you use your ThinkPad P14s Gen 3 with an external mouse, you've probably noticed the warm air blowing directly onto your mouse hand. This deflector elegantly solves that issue by redirecting the exhaust air upward, improving both…
This is a mount for a docking station I designed for a colleague to mount to the back side of his desk to free up space on top of the desk. Mount the model to the side or under your desk using strong double-sided tape.
Remix of thing:4463146 that keeps the laptop at a lower angle Print Settings Printer: Artillery Genius Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Any PLA Any How I Designed This =================== Category: Computer
I changed the gap between the 2 USB-C slots to 8mm to match my thinkpad. I widened the other half of the bracket too.
This is a screw organiser tray for the Thinkpad X13 Gen 4 ISO-layout keyboard. If you are disassembling an X13 Gen 4 to replace the keyboard, this will help keep the screws matched to their correct locations - there is one ‘well’ for each…
Lenovo ThinkPad E15 ethernet cover, useful to replace the original cover if it gets broken. Category: Replacement Parts
I needed some space on my desktop, so I took advantage of ThinkPad's ability to be opened "completely". Moreover, the screen is now at a more comfortable height for my neck. As this laptop is quite heavy, I didn't want it to fall upfront,…
the white wire needs to be connected to ground via a resistor to imply how much current can be drawn. |45 W |120 Ω | |65 W |280 Ω | |90 W |550 Ω | |135W |1 kΩ. | |170W |1.9 kΩ|…
