Activated-Carbon Add-On for “One Uppåtvind, please!” - Fully compatible to existing part
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Slip-on upgrade that lets Toms Uppåtvind HEPA take a second line of defense: an IKEA Nyttig activated-carbon filter
- Ocena
- 0 / 5
- Polubienia
- 11
- Pobrania
- 14
- Wydruki
- 0
- Wyświetlenia
- 480
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Share Alike
Activated-Carbon Add-On for “One Uppåtvind, please!”
(works with TOM / @Madewithlayers’ original filter as well as @Rolf_991381's horizontal version)
Slip-on upgrade that lets your Uppåtvind HEPA hood take a second line of defense: an IKEA Nyttig activated-carbon pad for odors and VOCs—no mods to the original part, no tools beyond longer screws.
Why you’ll like it
Double filtration: keeps the existing HEPA while adding real activated carbon in one tidy module.
Zero mods to TOM’s design: the sleeve simply slides over Tom’s housing and the parts latch to each other using the same joint geometry.
IKEA off-the-shelf: NYTTIG FIL 559 carbon filter (article # 900.279.72) drops straight in, held by an integral clamp and rear safety grille. 45€ in Germany.
Click-on, click-off: two rigid hooks plus a printed leaf-spring snap the add-on to Tom’s cover; removal for filter swaps takes seconds. Screw in the hooks using M3, the Spring using M4 Screws, either with Heat inserts or directly into the plastic.
No airflow drama: Core One’s twin blowers still maintain 30 °C build-chamber temp at 40 % PWM Max.
Compact: Gives you full access to the electronics, when using Rolfs remix.
Including Spacer: a small TPU gasket lifts Toms Part away from the printer frame to give the hooks the space they need; just swap in longer M3 screws. There is another TPU Gasket to join the old and new filter holders to each other tightly.
There is some space in between the two filters as to allow air to spread there in an attempt to reduce air resistance. Seems to have worked
Please note two things:
I've printed Rolfs Remix of Tom's Uppatvind for my printer as I've wanted to maintain access to the electronics. I therefore also bound my Design to it. Upwards compatibility to Toms original Design should be given, as the remix just swapped orientation.
The fotos of my version are from my personal iterations. In this version the grille was snapped on with magnets but I've later went on to adhere the grille with glue. In the uploaded version those parts are already one. You'll still find the magnet cavities when slicing though ;) I've added renderings of how it will look like now in version 2.

Suggested print settings
| Part | Material | Layer H | Walls | Infill | Supports | Notes |
|---|---|---|---|---|---|---|
| Holder & grille | PETG or PLA | 0.2 mm | 2 | 15 % grid | yes, for the 4 holder tabs. | Make sure to prohibit support for the screw holes using support modifiyers. Pritn laying flat with the grille to the bed |
| Hooks | PETG or PLA+ | 0.2 mm | 3 | 15 % | none | |
| Leaf spring | PETG | 0.2 mm | 3 | 100 % | none | I've used PETG CF for this. Make sure to add a modifyer box over the springy part and increase the perimeters here to get 100% in this area (See Foto) |
| Spacer + Gasket | TPU 95A | 0.2 mm | 2 | 15 % | none | you know your TPU best ;) |

Installation (4 quick steps)
Print the parts
Filter Holder in two parts, two hooks, leaf spring, and the TPU spacer and Gasket in 2 Parts.
Glue
Glue the filter holder (I've used UHU Allplast). Once dry set the Gasket in there with some drops of glue here and there and quite some more in the joint area. Other than that part it just needs to be enough to not fall out when installing.
Add the Spring and the Hooks
Using M3 Screws for the Hooks and an M4 Screw for the spring mount them to the nyttig holder. Use the slotted hole for tension adjustment later. Should your material be way different in flexibility than mine, use a scale factor in the springs axial direction to adjust and print again.
Add the Nyttig filter
Slide the cartridge under the tabs, folding it in there. Press it into the corners.
Install the spacer
Take off Toms holder, add the TPU Spacer and mount the holder again using slightly longer screws than before.
Slip on the sleeve
Push the new sleeve over TOM’s original Uppåtvind body with the Uppåtvind Filter installed —no sanding or trimming necessary.
Clip in & print
Hook the hooks under Tom's holder, use the spring to apply tension and pull the Nyttig onto the HEPA Holder. Thats it! As we've added some air resistance to the printer, make sure that you adjust your max. RPM settings should that be necessary (wasn't for me)
That's it - enjoy!
Happy for Feedback. I was thinking of adding filtration fan to it, but ended up tossing the thought.
