1 / 6
USB-C Ventilator for 40x40 Mini-Heki in Camper/RV/Motorhome/Van for Camping
Zamów wydruk tego modelu
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
An USB-C Ventilator for 40x40 Dometic Mini-Heki in Camper/RV/Motorhome/Van for Camping
- Ocena
- 4,333 / 5
- Polubienia
- 65
- Pobrania
- 242
- Wydruki
- 2
- Wyświetlenia
- 3651
- Oceny
- 3
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
SzczegółyPliki (5)Wydruki i komentarze (Wydruki: 2) (Komentarze: 3)Remiksy (0)Kolekcje (105)Powiązane
English (Deutsch weiter unten)
A fan that fits into the Dometic Mini-Heki (40x40xm). Inside width: 382mm.
Printing:
Print in ASA or ABS only, for temperature stability.
Required parts:
- 2x Corsair RS140 MAX 140mm (Link)
- 1x PWM Fan Control USB-C (Link)
- 8x M4 Nuts
- 1x M7 Nut (as flat as possible)
- Cable Tie
- USB-C Cable
- Optional if you want a flyscreen: A piece of gossamer and 8x M4x45 screws
Assembly:
- Decide if you want the air to blow in or out. Remove the rubber caps of the Corsair RS140 on the back side. See pictures.
- Use the included M4 screws and M4 nuts to attach parts 1,2 and 3 to the fans on the rubbercap side.
- Remove the cap of the PWM controlerl and stick it through the center hole of part 1. Then fix it with the M7 nut. Reattach the cap.
- Attach the included PWM Y-Cable to the fans and the PWM controller.
- Attach an USB-C cable to the PWM controller and thread the cable through the hole.
- Enjoy
Flyscreen (optional):
- Print each part of the flyscreen holder two times.
- cut the gossamer and place it between the top and bottom part.
- replace the M4-Screws (assembly step 2) by the longer ones and lock the flyscreenholder into position. Repeat for the second fan.
As always; No warranty. Print and use on your own risk.
Deutsch
Ein Ventilator, der in das Dometic Mini-Heki (40x40cm) passt. Lichtes Maß 382mm.
Drucke alle Teile in ASA oder ABS für Temperaturbeständigkeit.
Benötigte Teile
- 2x Corsair RS140 MAX 140mm (Link)
- 1x PWM Lüftersteuerung USB-C (Link)
- 8x M4 Muttern
- 1x M7 Mutter (so flach wie möglich)
- Kabelbinder
- USB-C Kabel
- Optional, falls Du ein Fliegengitter möchtest: Ein Stück Mückennetz, 8x M4x45 Schrauben
Zusammenbau:
- Entscheide Dich ob die Luft rein, oder rausgeblasen werden soll. Entferne die Gummis an den Schraubendurchführungen an der Lüfterrückseite (siehe Bilder)
- Verwende die mitgelieferten M4 Schrauben und die M4 Muttern um die gedruckten Teile 1,2,3 an den Lüftern anzubringen (An der Seite, an der die Gummis noch dran sind)
- Entferne die Kappe der Lüftersteuerung und stecke die Welle durch das mittlere Loch von Teil 2. Fixiere es mit der M7 Mutter und stecke die Kappe wieder drauf
- Schliesse das mitgelieferte Y-Kabel an die Lüfter, sowie die Lüftersteuerung an.
- Schliesse ein USB-C Kabel an die Lüftersteuerung an und fädle das Kabel durch die Führungen, sowie das Loch.
- Fertig.
Fliegengitter (Optional):
- Drucke jedes Teil für den Fliegengitterhalter 2x aus (Dateiname enthält “flyscreen”)
- Schneide ein Stück Fliegennetz zu und platziere es zwischen dem “bottom” und “top” teil des Fliegengitterhalters.
- Ersetze die kurzen M4 Schrauben mit den M4x45 Schrauben un schraube den Fliegengitterhalter fest.
Wie immer: Keine Garantie, Bau und benutzung auf eigene Gefahr.