1 / 7
Novritsch Anti-Fog for begadi CP1 — zdjęcie 1
1 / 7

Novritsch Anti-Fog for begadi CP1

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Anti Fog for begadi CP1 airsoft safety goggles using Novritsch AFU as base, RX and non RX versions.

Ocena
0 / 5
Polubienia
13
Pobrania
47
Wydruki
0
Wyświetlenia
380
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Sports
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

Anti-Fog Adapter für Begadi CP1 Airsoft-Schutzbrillen – kompatibel mit dem Novritsch AFU-System

Dieser Adapter ermöglicht die Nutzung des Novritsch AFU-Systems an den Begadi CP1-Schutzbrillen. Zum Ausschneiden der Öffnung im TPU-Rahmen der Begadi-Brille wird dasselbe Werkzeug verwendet, das dem Novritsch AFU beiliegt.

Material
Das Material ist nicht entscheidend. Empfohlen wird PETG, PLA ist jedoch ebenfalls geeignet. Auf den Bildern ist PA12-CF zu sehen.

Magnetbefestigung
Die Magnete werden als Presspassung eingesetzt. Dazu die Magnete zunächst auf die originale Magnetklemme legen, um die richtige Ausrichtung sicherzustellen, und anschließend die gedruckte Klemme vorsichtig auf die Magnete drücken, bis sie bündig sitzen.
Die gedruckte Magnetklemme sitzt sehr straff auf dem Luftkanal. Falls sie zu eng ist, die XY-Achse um 0,05–0,1 mm vergrößern und erneut drucken. Ist sie zu locker, genügt ein Tropfen Sekundenkleber.

Varianten der Magnetklemme
Es gibt drei Versionen, abgestimmt auf verschiedene Magnetgrößen, um die Kompatibilität zu erhöhen. Empfohlen sind 4 × 3 mm, da dies der gleichen Größe wie in der Novritsch-Version entspricht.

Varianten des Luftkanals

Non-RX (Standard): Leitet die Luft schräg in Richtung des  originalen PC-Brillenglases. Empfohlen für Nutzer ohne Brille oder mit Kontaktlinsen.

RX-Version: Entwickelt für Brillenträger. Leitet die Luft direkt auf den RX-Einsatz und nach vorne, da der Einsatz den Luftstrom der Standardversion blockieren würde.

__________

Anti-Fog Adapter for Begadi CP1 Airsoft Goggles – Compatible with the Novritsch AFU System

This adapter allows you to use the Novritsch AFU system with Begadi CP1 goggles. To create the cutout in the TPU frame of the Begadi goggles, simply use the same tool that comes with the Novritsch AFU.

Material
The material is not critical. PETG is recommended, but PLA also works fine. The material shown in the pictures is PA12-CF.

Magnet Mounting
The magnets are press-fit. To ensure the correct orientation, first place the magnets onto the original magnet clamp, then carefully press the printed clamp onto the magnets until they sit flush.
The printed clamp fits very tightly onto the air duct. If it is too tight, increase the XY dimension by 0.05–0.1 mm and reprint. If it is too loose, a single drop of superglue is sufficient.

Magnet Clamp Versions
There are three versions available, depending on magnet size, to improve compatibility with what you may already have on hand. The recommended size is 4 × 3 mm, which matches the magnets used in the Novritsch version.

Air Duct Versions

Non-RX (Standard): Directs airflow at an angle towards the goggles. Recommended for users without glasses or for those wearing contact lenses.

RX Version: Designed for glasses wearers. Directs airflow straight to the RX insert and forward, as the insert would otherwise block the optimal airflow of the standard version.

Tagi