Novritsch Anti-Fog for begadi CP1
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Anti Fog for begadi CP1 airsoft safety goggles using Novritsch AFU as base, RX and non RX versions.
- Rating
- 0 / 5
- Likes
- 13
- Downloads
- 49
- Makes
- 0
- Views
- 396
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Other Sports
- License
- Creative Commons — Attribution — Noncommercial — NoDerivatives
Anti-Fog Adapter für Begadi CP1 Airsoft-Schutzbrillen – kompatibel mit dem Novritsch AFU-System
Dieser Adapter ermöglicht die Nutzung des Novritsch AFU-Systems an den Begadi CP1-Schutzbrillen. Zum Ausschneiden der Öffnung im TPU-Rahmen der Begadi-Brille wird dasselbe Werkzeug verwendet, das dem Novritsch AFU beiliegt.
Material
Das Material ist nicht entscheidend. Empfohlen wird PETG, PLA ist jedoch ebenfalls geeignet. Auf den Bildern ist PA12-CF zu sehen.
Magnetbefestigung
Die Magnete werden als Presspassung eingesetzt. Dazu die Magnete zunächst auf die originale Magnetklemme legen, um die richtige Ausrichtung sicherzustellen, und anschließend die gedruckte Klemme vorsichtig auf die Magnete drücken, bis sie bündig sitzen.
Die gedruckte Magnetklemme sitzt sehr straff auf dem Luftkanal. Falls sie zu eng ist, die XY-Achse um 0,05–0,1 mm vergrößern und erneut drucken. Ist sie zu locker, genügt ein Tropfen Sekundenkleber.
Varianten der Magnetklemme
Es gibt drei Versionen, abgestimmt auf verschiedene Magnetgrößen, um die Kompatibilität zu erhöhen. Empfohlen sind 4 × 3 mm, da dies der gleichen Größe wie in der Novritsch-Version entspricht.
Varianten des Luftkanals
Non-RX (Standard): Leitet die Luft schräg in Richtung des originalen PC-Brillenglases. Empfohlen für Nutzer ohne Brille oder mit Kontaktlinsen.
RX-Version: Entwickelt für Brillenträger. Leitet die Luft direkt auf den RX-Einsatz und nach vorne, da der Einsatz den Luftstrom der Standardversion blockieren würde.
__________
Anti-Fog Adapter for Begadi CP1 Airsoft Goggles – Compatible with the Novritsch AFU System
This adapter allows you to use the Novritsch AFU system with Begadi CP1 goggles. To create the cutout in the TPU frame of the Begadi goggles, simply use the same tool that comes with the Novritsch AFU.
Material
The material is not critical. PETG is recommended, but PLA also works fine. The material shown in the pictures is PA12-CF.
Magnet Mounting
The magnets are press-fit. To ensure the correct orientation, first place the magnets onto the original magnet clamp, then carefully press the printed clamp onto the magnets until they sit flush.
The printed clamp fits very tightly onto the air duct. If it is too tight, increase the XY dimension by 0.05–0.1 mm and reprint. If it is too loose, a single drop of superglue is sufficient.
Magnet Clamp Versions
There are three versions available, depending on magnet size, to improve compatibility with what you may already have on hand. The recommended size is 4 × 3 mm, which matches the magnets used in the Novritsch version.
Air Duct Versions
Non-RX (Standard): Directs airflow at an angle towards the goggles. Recommended for users without glasses or for those wearing contact lenses.
RX Version: Designed for glasses wearers. Directs airflow straight to the RX insert and forward, as the insert would otherwise block the optimal airflow of the standard version.