Corvus mATX (Micro-ATX) - 3D Printed PC Case - Voron Inspired

What's better than a big Voron? A small one! Remixed from the original Voron V.PC - 3D Printed Case to fit the mATX form factor.

This build should fit the following:

• mATX & ITX Motherboard

• 199mm tall Air Cooler Tower

• 345mm long GPU (approximately)

• Standard ATX power Supply (fits below).

• 140mm & 60mm fans (Rear)

• 120mm fans (Front)

• 2x 140mm(Top)

• Blank acrylic panel DXFs are included for adding additional fans to or using as windows

Corvus ATX to mATX Conversion

The full kit including unchanged parts have been provided. Below highlights the key changes and required conversion from @MandicReally's Full ATX design.

You will need to shorten the rails highlighted red:

• Vertical -> 400mm to 300mm

• Horizontal -> 400mm to 350mm

You will need to reprint the following parts in yellow:

• Motherboard Mounts

  • Side

  • Bottom

• Hidden Cable Channel

  • Top

  • Bottom

• Panel - Deck (Printed) [If used on ATX version]

  • Panel Back

  • Panel Front

• Panel - Rear Components

  • Expansion Slots

• Panel - Rear Fillers (Printable) [If used on ATX version]

  • PCIe Filler 60mm Fan

  • PCIe Filler Blank

  • PCIe Filler Hex

  • PCIe Filler Partial Hex

• Skirt - Panels

  • Side Skirt A Closed

  • Side Skirt A Open

  • Side Skirt B Closed

  • Side Skirt B Open

• Top Hat

  • TH Left Front

  • TH Left Rear

  • TH Right Front

  • TH Right Rear

You will need a full, new set of acrylic panels even though the width remains the same. All DXF's can be found in Panels - Acrylic DXF

====Details from Original Corvus ATX w/ highlighted Modifications===

What’s Included in the Download?

• Core Frame Brackets & Mounts (Motherboard tray, PSU mount, GPU support)

• Panel & Skirt Files (Side panels, bottom skirts, feet)

• Accessory Parts (Fan brackets, drive mounts, RGB channels)

 Print Settings & Recommendations (From Original Corvus ATX)

• Nozzle: 0.4 mm

• Layer Height: 0.2 mm

• Walls: 4+ perimeters for strength

• Top/Btm Layers: 6+ for rigidity

• Infill: 40%+ (Rectilinear, Gyroid, or Cubic recommended)

• Material: ABS/ASA (best), PETG, or PLA+ (probably fine)

• Support-Free (Some can help on obvious parts, but aren't required.)

Hardware Required (**Modified from Original Corvus ATX)

• **2020 Aluminum Extrusion (4x 350mm + 4x 300mm  + 4× 200 mm default spec)

• Front Skirt Parts for use w/ PCB Front Button Mod, found here: V.PC Basic Frontpanel PCB

• M5 Button Head Screws

• M5 Roll-In Nuts

• M3 Button Head Screws (2x this kit as you need a lot of M3x8)

• M3 Roll-In Nuts

• M3 Hammerhead T-Nuts

• Acrylic Panels (Laser cut or CNC’d)

• M3 Heat Inserts (standard Voron Size: M3x5x4)

• 2x Mechanical Keyboard Switches

• 2x 5mm LEDs

• PC Hardware

• 1mm Foam Tape

• VHB Tape

• 6mm x 3mm Magnets

Credit (Updated): 

• @DonaldSayer - Originator of this design, laid the ground work to make it happen.

• Voron Design Team - Inspiring makers in ridiculous ways since… idk, a while…

• quattroerik - Door Hinges remixed for this project: LINK

• @MandicReally - Original Corvus ATX Voron Inspired Design

Notes & License

• Not an official Voron project — just heavily inspired by their design philosophy.

• GPL-3 Open Source License - Please support those who make these projects possible.

• Remixing encouraged, just credit and link back.