1 / 3
HOn30 Freelanced Four-Wheeled Cars — zdjęcie 1
1 / 3

HOn30 Freelanced Four-Wheeled Cars

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Small freelanced freight cars designed for FDM printing

Ocena
0 / 5
Polubienia
12
Pobrania
66
Wydruki
0
Wyświetlenia
272
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Ideas
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Here are a few freelanced 4-wheeled cars to round out your rolling stock. These models utilize my wood side dump car chassis and were designed to be printed on an FDM printer with a standard 0.4 mm nozzle and 0.12 mm layer height. These were designed to utilize Micro Trains wheelsets and 1015 couplers.

Tips for printing:
Print the parts with the flattest surface facing downwards towards the print bed (I've included a photo that shows how I orient my parts.)

Assembly:
What you’ll need: Printed components, couplers, wheel sets, super glue, hobby knife, small file or sand paper (just in case of fitment issues), and any additional detail parts you want to add.

Since these use the same frame as the dump cars the assembly is the exact same. Start by fitting the side frames into the frame, the beveled sides should face downwards and the tabs should fit into the notches. I find it best to start one end of the side frame then gently bend it and the frame support to make room to seat the second tab. Once it’s seated lightly squeeze everything together. Do this for both sides. Depending on your printer, material, and settings you might need to clean up the holes in the frame with a hobby knife. Next add the center bolster, bend the side frames outwards gently to make room and push the center bolster up from the bottom. It should hug the frame and there are two tabs it should sit between for alignment. Once it is in place gently press the side frames so the notched portion of the center bolster fits into the holes in the center of the side frames. You can add the wheels next, these should press in from the bottom, you may need to slightly bend side frame to start these. Once the wheel sets are seated, you can adjust the side frames to make them roll easier by bending them out slightly. Once you’re happy with how it rolls you can add a dab of superglue onto the ends of the side frames and the connection with center bolster to lock everything in place. Finally add the couplers into the pockets on the ends of the frame. I used M1 x 4mm screws to attach my couplers.

For the caboose glue the pilots to the end beams, then glue the body and end beams to the frame. There aren’t any alignment tabs for this unfortunately, but I found it’s best to glue one end beam, then the body, then the final end beam. The doors press in from the inside, some sanding may be needed to ensure a proper fit, especially on the bottom if your printer has issues with “elephant’s foot”. The roof prints as one piece, fold it along the provided seam and glue it to the body using the tabs to align it.

The boxcar body can be screwed to the chassis using M1 x 3mm screws. Like the caboose the doors press in from the inside, some sanding may be needed to ensure a proper fit, especially on the bottom if your printer has issues with “elephant’s foot”. The roof folds along the provided seam can be glued in place.

For the for the flat car, bulkhead flat car, and gondola, glue the flat car deck to the chassis, pins are provided for alignment. If desired glue the bulkheads to each end of the deck or for the gondola glue the gondola body to the deck.

There are pockets on the underside of the frame over the axles to add weight if desired.

Final notes:
These models make use of a lot of previous designed parts including the dump car frame, dump car body for the gondola, and pilots from the boxcab for the caboose.

This chassis was designed for 36” wheels with a 0.537”/0.54” axle length however 33” wheels can be used as well. This includes Micro Trains and Evemodel wheel sets (both plastic and metal wheels work).

The frame is designed to use Micro Trains 1015 couplers, but any equivalent coupler could be used including Atlas Accumate and McHenry couplers. If there is an interest, I can model a hook and loop style coupler as well.

The material used to print this model really makes a difference. I had no issues with the silver PLA I use to prototype; however, the black PLA I used for the final models proved to be brittle making fitting the side frames difficult without breaking the supports on the frame, luckily you can always print more. Funnily enough the second black PLA I’ve tried isn’t brittle and assembles nicely however it doesn’t make as nice of a bearing surface for the axles. While they still roll good they don’t roll as well as the brittle ones. I have no idea why this is.

The models pictured are my personal models that have been painted and detailed. For the logging caboose I added glazing cut from clear packaging, a tin roof made from aluminum foil, and a smoke jack made from a Micro Trains sprue.

If you have any comments, questions, suggestions, or funny remarks feel free to reach out to me. As always, I hope to be sharing more of my models in the future and if you have any suggestions for models you’d like to see in HOn30 let me know.

Best Regards,
Dr. Fixet

Tagi