1 / 7
Ender 3 NG v1.2 reinforced integrated ProtoXtruder 2.0 with PC4-M6 fitting — zdjęcie 1
1 / 7

Ender 3 NG v1.2 reinforced integrated ProtoXtruder 2.0 with PC4-M6 fitting

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A stronger ProtoXtruder 2.0 appropriate for high chamber temperatures

Ocena
0 / 5
Polubienia
30
Pobrania
124
Wydruki
0
Wyświetlenia
833
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a reinforced ProtoXtruder 2.0 designed as a bolt-on upgrade for the Ender 3 NG v1.2!  It's designed to survive the stress of high-temperature heated chambers, has a PC4-M6 fitting, and uses more parts from the Ender 3 NG v1.2 BOM.

Here's a list of improvements compared to the original ProtoXtruder 2.0!

  • Greatly reinforced with more plastic to prevent deforming under high-temperature heated chambers (60C+).  Extruders are already under a lot of stress, and putting them in high heat from a heated chamber, plus the added heat of being against the stepper motor and near the hot end, makes ASA more pliable.  The first gear's bearing mounts are especially susceptible to deformations.  In my experience, after about 20 prints with the original extruder in a 65C heated chamber, the bearings become loose and the print quality suffers.  This improved model makes every area that handles stress stronger, and is suitable for long-term use in a hot heated chamber.
     

  • Idler arm closes the extruder teeth an additional 1 mm to prevent jams from hot, soft filament.  When printing in a hot heated chamber (65C+), air-cooled heat breaks get quite a bit hotter than when printing in ambient temperature, therefore the filament gets hotter and softer.  With the original design, it is possible for the filament teeth to wear notches in the soft filament, which makes the teeth slip, and results in failed prints.  With 1 mm more clamping distance, soft filament remains gripped even when deformed, and prints succeed when they would otherwise jam.

  • Idler arm's axle hole capped at one side to prevent pop-out.  The original design had both sides of the gear axle exposed, where this model has one side capped.  When the extruder is under a lot of stress, the axle has a tendency to pop out forward.  This model caps this side to prevent the axle from popping out.
     

  • PC4-M6 fitting to hold PTFE tube to the extruder.  The original Ender 3 NG v1.2 integrated ProtoXtruder 2.0 design simply has a hole on the top for PTFE tubing.  This simply does not hold the tubing well, and the tubing often becomes disloged during a print.  While this causes problems of its own, it's also a blocker for multi-material setups, because filament cannot be reliably removed and added to the extruder.  This model adds a PC4-M6 fitting to solve all these problems and provide easier maintenance.
     

  • Uses M3x4x4.5 heat set inserts that are used in the Ender 3 NG v1.2 BOM.  The original ProtoXtruder 2.0 uses M3x5x4 heat set inserts, which are different than the rest of the inserts used in the Ender 3 NG v1.2.  This model replaces the three M3x5x4 heat set inserts with M3x4x4.5 inserts that is used in the Ender 3 NG v1.2 build, which means that you can build this extruder with parts you already have.
     

  • More appropriate self-tapping idler arm screw size and idler pivot hole sizes.  On the original ProtoXtruder 2.0, the self-tapping idler arm screw hole is much too large, and it is very easy to strip.  This model reduces the self-tapping hole from 2.9 mm to 2.6 mm for a confident thread tap.  Additionally, the idler arm's pivot hole was widened from 1.6 mm to 1.75 mm to prevent the arm from jamming on the screw.

Here is the BOM!

 Not building an Ender 3 NG v1.2?  Use my reinforced standard ProtoXtruder 2.0 instead!

Tagi