Liczymy pasujące modele…
This is my improved version of the classic Flexi Rex. Somehow this version became the most popular one, maybe just because it doesn't break easily when handled by kids (and adults of course). I uploaded this model to Printables for…
Wydruk około 1,24 €–1,52 € nettoWstępna wycena jednego wariantu
I am huge fan of Formula 1 and cars, so I decided to add my model "Formula Tyrell P34 1976 Kid Toy (stronger with function wheels, 1:24)" to the ongoing Toy Cars Prusa Contest. I took and remodeled two original models by rkxone and…
Wydruk około 0,55 €–0,68 € nettoWstępna wycena jednego wariantu
I am huge fan of Formula 1 and cars, so I decided to add my model "Formula Tyrell P34 1976 Kid Toy (stronger with function wheels, 1:12)" to the ongoing Toy Cars Prusa Contest. I took and remodeled two original models by rkxone and…
Wydruk około 3,19 €–3,90 € nettoWstępna wycena jednego wariantu
My hand cranked turbine blower is cool and works fine - however you have to crank it really fast for a nice blow. So i tried to add another planetary gearbox - and it works so much better (and unfortunately louder). All parts are 3d…
PLA works ok. PETG will be better. 100% infil will give you the best strength.
wanted it slightly thicker Category: DIY
READ FIRST : I provided two versions. I highly suggest printing the stronger version. When the CFS is fully loaded, the original version will sag. The stronger version stops this from happening. This is a recreation of @TozzEmak's K2 PLUS…
Print in PLA with 5 walls; yields very strong part with little to no flex. For me, the OG version would either delaminate or just break during unwinding.
Remix of Hand Push/pump drill with stronger replaceable jaws, the lower part was too weak new one is stronger
Thank you so much to inlinerbutch who made the inital stand that I remixed from! This is a fantastic stand that folds up nicely to pack up my G90 . Unfortunately there were some sharp right angle corners on the stand that happened to snap…
Stronger Version of the Cloud Shelves I've seen on here… Can be printed in PLA and not bend under the immense pressure of all you Butt Wipe! Mines been up for a year and still holding the Poopy Paper High! Happy Printing!
CLICKBase was the best Gridfinity base… till now. DON'T PRINT WITH PLA, USE PETG! or any filament with less creep. Use ARACHNE! This model makes use of thin walls for support structure and is optimized for a 0.4 nozzle. ( CLASSIC should…
A clip for a Twingo rear parcel shelf, but a lot stronger :-D. I made and printed this part. I hope it will help a few people :-). PETG, nozzle= 0.4mm, print height= 0.2mm, without backing.
I got tired of dealing with the flimsy designs for the Blind Shaker Mount so I designed my own. Not only is this design stronger and more rigid, it also allows for the shaker to be held in two different ways. 1. With the lid on top held…
Simple way to cleanly peel an orange without getting gunk under your fingernail.
A slightly stronger version of the original, with more space around the bolts and more material holding the CR touch in place
This model enhances the mechanical strength of existing pipe/rod connectors about 5 times by strategically optimizing layer adhesion with an reinforcing ring element.
(french available after the English description!) We loved the RepRack system when we discoverd it. A big thanks to the original creator! But as the Fusion360 project file was available (another big thanks!) we decided to adapt it to our…
***THIS MODEL HAS BEEN REPLACED WITH AN UPDATED VERSION*** https://www.printables.com/model/1053384-floatwheel-adv-printable-bumper-20 My stock bumper keeps cracking at the point where the small "ears" protrude so I wanted to try to make…
Support only for the upper hex slot. Recommended to print out of something more solid than PETG. PC would work the best.
I added material to the base so it is stronger and does not require a brim to print
The original model by FunkyArt has the screws printed vertically which puts the layer lines parallel with the stressing forces of tightening them down, this increases the chance of the print failing or breaking along the layer lines. The…
one by one, the supplied corner attachments failed on my cheap amazon clothes rack, surprised pikachu face later in catastrophic fashion. so I printed my own in petg, 0.2 layer height, 3 walls, 20% gyroid infill on bambulab p1s I actually…
A remix of https://www.printables.com/model/252584-dodecahedron-lampshade
A full thicker back buffer plate to add the the MMU3 Buffer Box to contain the buffered filament better than simple bars.
A remix of Printojet's amazing design. Strong enough to be used without the front bar support with 2 sets of stiff springs. Bolt fork much stronger to cope with sudden joystick end-of travel bumps. Designed to have no flex with PLA <40%…
[English] I've tried various buffers and auto rewinders for MMU2S, and I finally found something satisfactory. That name is “Stronger Compact Spool Auto-Rewinder by rans”. It is great that it rewinds moderately, even if there is a lot of…
Greatly reduced the amount of holes on the top and bottom, also adjusted the main body to increase overall strength. I also shrank the height of the container to make a 50 mm puck sized container:…
This model enhances the mechanical strength of existing pipe/rod connectors about 5 times by strategically optimizing layer adhesion with an reinforcing ring element.
First, let me say I am sorry about the image quality. This is a filament shelf bracket designed for ½ inch dowels. It was modified in FreeCAD. I would print this using at least 4 top/bottom layers, 3 walls and 20% infill (I use infill…
Polydryer drybox adapter bracket for Stronger Compact Spool Auto-Rewinder by Rans A modified axle with slits on both ends and an axle bracket that allows for the spool rewinder to slide nicely onto the drybox's existing spool holder…
Slimmer, Stronger and locking remix of the Clipper keychain by Marekp. Stood the test of driving over with a car and the locking tab still holds up after a year of fidgeting with it. Printed with PLA at 0.2 layer height and 5 walls.
Added another layer to the original design to hold the individual Battery strap strongly in place - minimizing potential damage to the FC/O4 air unit during a crash. Added a version that holds the XT30 cable firmly in place, away from the…
Originally printed the Drybox from Prusa Guy but the first Prusament spool I inserted was due to some production fail 2 mm wider and could not fit in. So tried the mod from DG-RoboTek that gave me the extra milimeters but already during…
I recommend using the supports I included. The origin is set the same as the model (use supports marked "square" for the tray with ends marked "square") so that you can use the "Join" feature of your slicer. You could also use your slicer…
This is a shower shelf with for a 25 mm shower bar designed for prusa mini with a razor emplacement with a stronger clamp to prevent the opening with the weight (and time)
Glass eyes really give this little fella a whole lot more personality! :) I uploaded the 3mf file containing modifiers to allow for 2 x 6mm glass eyes to be inserted. No supports required. Holes for eyes should appear after slicing.…
The 3D modelled Solder Paste and Flux Dispenser is a compact and efficient device, perfect for electronics assembly. Its ergonomic design makes it easy to use, with adjustable dispensing volumes ensuring accurate and consistent results…
I accidentally bent the two side screw holes apart when trying to add tension to the servo. I thickened the sides a bit to keep this from happening. Low Rider MMU by GcodeGearHead
Original modified to add support and embossed the model name. Otherwise the design stayed the same. I just grabbed the bottom section and pasted it in a number of times to extend it. Modifications here on Tinkercad:…
The original design is excellent, but I added a larger slot and a full through-hole so that you can wrap a bore snake cord around it for more leverage.
I simply added space inside the shaft to create additional thread reinforcement (roller-71 & 75).
Este remix es para el diseño original https://www.printables.com/model/73094-articulated-bender , al cual se le modificaron las articulaciones usando este otro diseño…
A full thicker back buffer plate to add the the MMU3 Buffer Box to contain the buffered filament better than simple bars.
The model is optimized to print flat on the bed, making printing simple and reliable with no supports required. Feature
Increased diameter of model's base stand from 3mm to 3.7mm to increase strength.
I loved this keychain! But eventually the ring broke due to being weak. I have redesigned it to be thicker and hopefully stronger with a slightly larger ring. Add custom text in Tinkercad or your modeling software of choice. This tutorial…
strongerst cover Ender 3 V3 SE Single 5015 Fan by nora
A Strong/thicker version of the Samla box lock clips. Mine were printed with these settings: 0.6 mm nozzle 0.3mm layers 3 perimeters brim enabled (the uneven layers resulted from a dirty z-axis lead screw)
A stronger upper leg for Colossus 13! Now it can stand up more easily! Honestly, I've wanted to make a stronger upper leg for Colossus 13 ever since I printed it, because it had a REALLY hard time standing up by itself, but now with this…
I modified the original, so that the thin parts that goes into the wall/board does not break as easily. This is the M5 version I recommend you print in the orientation shown, so that it improves the strength of the weakest points even…
Based on vascosim's excellent remake of the muzi.works model. No supports need. Snip the support at the end of the internal antenna shaft if desired. Fits Heltec V4 and GPS, standard stubby antenna and 3000mAh Meshnology battery. Link to…
This is a remix of Steve DeGroof's Dragon Bookmark which is a remix of MZ4250's Red Dragon. I changed it so that the insert extends further into the dragon for more strength. Printed in two parts, the dragon head and the insert.
Ceiling lamp cable holder to attach a cable to the ceiling. Printable laying on the side for stronger orientation of the layers. Most models I've seen are printed with the layers slicing the mount horizontally when on the ceiling. Which…
This project presents my improved version of 3D printed battery terminal covers , designed for durability, easy printing, and a perfect fit. The new design enhances protection against dust, accidental contact, and corrosion, while keeping…
A simple door hook to hang something on the door (tested on a jacket).
Build plate GoPro mount for your Ender 3 V3 KE printer. Also includes a plate for a Nebula camera with a GoPro-style connector.
The original part broke twice. Therefore I created a new version. based on the original.
Improved the strength of the tab. In the comparison photos (with two parts side by side), the part on the left is this model while the one on the right is the original design I modified from. Printed in eSUN Fire Engine Red PETG with 0.2…
The Door Lock Rod Clip v2 Meet the new and improved clip designed for 4mm diameter rods that need to take a 90-degree turn just a cm from the end into a 6mm hole. This is a redo of my original design (…
Print in PLA with 5 walls; yields very strong part with little to no flex. For me, the OG version would either delaminate or just break during unwinding.
Original model were too fragile for me and had a gap on top of my stepper, so I decided to make a stronger and slimmer version. It's a X axis Stepper motor cover that also doubles as toolhead cable clip. There is two versions: - With…
The original basket weave design by psychprod is ingenious, but being me, as soon as I printed it I knew I would like to tweak a few things, and, again being me, the best way to do so would be to remodel the whole thing from scratch...…
Halfway through the print pause your printer and add 1-2 small spit shot weights to make the rattle inside. Once printing complete add three small split rings and two treble hooks. Happy catching!
A backplate to hold the stock or other compatible CPU cooler for an AM4 motherboard. This design is slightly stronger than the original on Thingiverse, as I made the pegs slightly larger and the hole slightly smaller. DO NOT tighten the…
Remix of nokiri design with the joints redesigned and easier to print. I sized it down also so it would fit on my E5P.
This one-hand catapult can be used to shoot tiny items around for fun. The raised bucket makes it harder to aim when using the full travel compared to the original model, but with some practice, shots over quite some distance are…
This model improves the robustness of the print. It still requires a high level of precision for the leg's strength.
I reinforced the standard holder because it was too weak.
I had the original grip design break when using it as a pump grip on a nerf blaster, so I made this version where the neck is solid and it uses a bolt to secure it to the rail, and the inside becomes a storage container. Hardware: M5 x…
The original screws were printed vertically. After using the original screws for a few months, it started to split at the layer lines, so I decided to make these screws, that you can print horizontally on the bed, which also gave it an…
I printed two of the original version and one broke coming off the build plate and the other broke when my son dropped it at a Star Wars event. I have uploaded a thicker version of the hilt as well as two rings that can be used to repair…
A remix of Printojet's amazing design. Strong enough to be used without the front bar support with 2 sets of stiff springs. Bolt fork much stronger to cope with sudden joystick end-of travel bumps. Designed to have no flex with PLA <40%…
The tracks did not keep together as the train traveled on top of them. I noticed (and tested) that https://www.printables.com/model/889614-lego-flexible-train-track-rail have a very strong locking design, so I use them to modify the…
I wanted a stronger setup for the rollers. The little nib axle works well for filament rollers but not people
Just added supports to the feet as they all quickly broke off the one I gave to my son.
I reinforced the standard holder because it was often too weak. It has stronger sides for holding the heater block and more material in certain areas. It fits the MK4S printer with a silicone sock installed and E3D nozzle I recommend…
I adjusted the pin shape due to wiggly hinge when printed with cheap PETG. I think that this is due to weak adhesion of first “sharp” layer of the hinge´s circle. Be sure that you have good first layer.
[English] I've tried various buffers and auto rewinders for MMU2S, and I finally found something satisfactory. That name is “Stronger Compact Spool Auto-Rewinder by rans”. It is great that it rewinds moderately, even if there is a lot of…
I had issues with the mount flexing and eventually snapping off. I had some 2mm metal pins left over from another project so I added holes to insert a couple of those. I also replaced the locating pins with holes so screws can be added to…
I wanted a stronger bag clip without an increase in it's physical size. Designed in Fusion360 by myself and Nikolai Schauer from the ground up. Spring mechanism designed with the help of AI, tapering down the handles on both sides using…
Walnuts Cracker with stronger walls Thanks steve5092 for your amazing design
Recommend printing with at least 15% infil. This is ment to be used with:…
Update v2: Added a sturdier and easier to print version optimized for printing on the diagonal upper chamfers. Step file included, so you can adjust as well if needed. Bought myself a telescopic snow-broom/ice-scraper from Biltema (…
Thicker hook springs and steeper hooks. Worked better for me when printing in PETG.
I do not suggest scaling, there were flaws when i scaled up
Update: I have added new version (prototype) with two bumps that should snap onto the top rooster ribs. See file StrongHookClick It works with my no name brand radiators. I don't expect that all radiators are made with the same dimensions…
The original was too flexible for TPU. Added some bits to make it stronger. Print at 98.5-98% scale for good fit.
The clips were coming off very easily (might be totally because of my bad settings), so I added 3mm fillets to strengthen the clips a little bit.
Print using 2 walls so it doesn't print the small dots at each radial rib, which is a waste of time.
I didn't like how the fins were super thin and were basically just a bridge layer so I removed two of them, thickened up the remaining two, and added a support bridge down the middle to strengthen them. I also adjusted the angles of the…
Just the dummy 13 base but without the letters and numbers on the top and bottom for a more full and sturdy base.
Greatly reduced the amount of holes on the top and bottom, also adjusted the main body to increase overall strength. I also shrank the height of the container to make a 50 mm puck sized container:…
A stronger version of the curved spider for the Caldwell telescope
made more material by the screw hole to stop breakage
i found that the tread on my tracks were often snapping off so i redesigned them to be a little stronger
![Ender 3 V3 SE/KE X Axis Stepper cover with cable clip. [Slimmer and stronger] With optional spine cable chain](https://media.printables.com/media/prints/997542/images/7590934_1fce7923-c1f7-4fa5-bd72-395bbf9c98d6_c07266b5-b580-4bab-a593-653b146c3dd0/pxl_20240905_165430364.jpg)
![Stronger Bag Clip [Updated]](https://media.printables.com/media/prints/fce332a5-b5e4-4515-b020-20e05cede987/images/9700414_90444613-ad8b-4e86-b100-8b257781514d_4aad224e-8688-48da-80d6-e5c9483dc8fe/20250507_052745.jpg)
