1 / 2
Under Desk Mount QUBE 500 — zdjęcie 1
1 / 2

Under Desk Mount QUBE 500

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Robust under-desk mount for the Cooler Master QUBE 500, removable from the case with only 2 screws

Ocena
0 / 5
Polubienia
2
Pobrania
10
Wydruki
0
Wyświetlenia
117
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Overview — Features & Advantages

This is a robust under-desk mount for the Cooler Master QUBE 500, designed to securely hold the PC while still allowing easy removal for maintenance or transport.

Only two screws attach to the stock threads and need to be removed to return the case to its original, stock configuration — ideal if you want to take the PC to a LAN party or move it frequently.

The mount uses the included rear handle of the QUBE 500 as a primary attachment point and provides good clearance for the front USB ports and audio jack.

Additional advantages:

  • Keeps the PC off the floor

  • Easier cleaning under the desk

  • Less dust, hair, and debris entering the case

  • Compatible with front exhaust setups to avoid heat buildup under the desk

Once installed, the top of the PC sits approximately 123 mm below the desk.

READ THE WHOLE DESCRIPTION IF YOU DECIDE TO PRINT THIS.


Compatibility & Use Case

  • Designed specifically for the Cooler Master QUBE 500

  • Fully compatible with my QUBE 500 front duct / shroud

  • Allows a front exhaust configuration

  • Helps prevent heat from being trapped under the desk


Hardware, Materials & Tools Required

Desk Requirements

  • Designed for a 25 mm thick tabletop

  • If your desk is thinner or thicker, different screw lengths can be used

⚠ Important:
If you have a hollow desk, the screw attachment will be significantly weaker. Use extra caution.


Screws & Hardware

Desk mounting (per hook)

  • 2×   35×4 mm wood screws

With this setup, approximately:

  • 20 mm of screw engages the desk in the front hooks

  • 18 mm engages the desk in the back and locking hooks

The 35 mm screws are plenty strong for solid wood.
Leaving 5–10 mm from screw tip to desk surface is recommended to avoid damage or visible bumps.

Case mounting

  • 2×   M4 15 mm screws

  • 2×   13 mm diameter washers

Only these two screws are required to remove the PC and return it to stock.


Tools Required (Very Important)

You must use a long-shaft screwdriver for the wood screws.

  • Phillips screws used

  • 122 mm shaft screwdriver was just enough for the rear handle hooks.

⚠ Without a long-shaft tool, installation will not be possible.


Files to Print / Part Overview

Front_case_hooks.stl

  • The only parts that attach directly to the PC case

  • Mount to the QUBE 500 using the rear handle

  • Require only 2 × M4×15 mm screws and 13mm diameter washers to attach and remove the PC


Front_desk_hook.stl

  • Standard front desk hook

  • Use this if you do not need lateral locking


Front_desk_hook_with_lock.stl

  • Front desk hook with a side-lock feature

  • Required if you use only one Back_Handle_Hook

  • Prevents the case from sliding sideways out of the mount


Back_Handle_Hook.stl

  • Rear hook that attaches to the desk and interfaces with the QUBE 500 back handle

  • Can be used:

    • Alone (centered, requires at least one locking front hook)

    • In a pair for additional support


Recommended Mount Configurations

✅ Recommended Setup (balanced & simplest)

  • 2 × Back_Handle_Hook

  • 2 × Front_desk_hook

  • 1 × Front_case_hooks

Provides good stability without requiring locking hooks.


🔒 Locked Setup (maximum security)

  • 2 × Back_Handle_Hook

  • 2 × Front_desk_hook_with_lock

  • 1 × Front_case_hooks

Best option for pcs that could be bumped or if you want maximum resistance to sideways movement.


⚠ Minimal Setup (NOT recommended)

  • 1 × Back_Handle_Hook

  • 1 × Front_desk_hook

  • 1 × Front_desk_hook_with_lock

  • 1 × Front_case_hooks

Works, but has less redundancy and higher stress on each hook.
Use only if material is very limited and if you feel confident it will be enough.


Printing Settings & Materials

Material

  • ABS (used and recommended)

  • Do NOT use PLA

    • PLA may soften due to internal PC temperatures

    • This is a structural part


Base Print Settings

  • 4 walls (0.6 mm each)

  • 35% gyroid infill

  • ~5 top & bottom layers (0.2 mm each)

  • Support only required for the Front_case_hooks (if printed in the original fila orientation)


Reinforced Sections (Modifiers Required)

I used modifiers for 100% infill in critical areas
(method may vary depending on your slicer).

Reinforced areas:

  • Top of the Front_case_hooks, where the M4 screws attach to the case

    • Approximately 84 mm and up (based on the shared file orientation)

  • Top section of all hooks, where the wood screws attach

    • Reinforce the top 18–20 mm

    • “Top” refers to the installed orientation, not the print orientation


Printing Orientation & Adhesion

  • Recommended to print hooks lying on their sides

  • Bed adhesion tabs are strongly recommended

    • Used 20 mm diameter cylinders, 0.8 mm height

  • All parts are oriented in my recommended print orientation, except:

    • The locking hook, oriented to avoid supports
      (this orientation may not be the strongest)

Use your own judgment for orientation and slicer settings.


Installation & Clearance

The top and front panels can be installed and removed using a slight angled motion
(insert one side first under the printed part, then rotate the other side into place).

Clearances are very tight, but this can be easily corrected with sanding in specific areas if needed.


Warping, Measurements & Installation Accuracy

The values below are theoretical. Slight variation will only cause minor misalignment.
An image with the measurements is attached (top = back hooks, bottom = front hooks).

  • Warping must be carefully managed, especially on the back hooks

  • Installation accuracy is critical:

    • Front and back hooks must be parallel to each other and to the desk

    • Gap between back hooks: ~128 mm
      (each hook offset by 2.8 mm to clear the rounded handle)

    • Gap between front hooks:

      • 133.6 mm (two non-locking)

      • 129.6 mm (one locking + one non-locking)

      • 125.6 mm (two locking)

Incorrect positioning will cause uneven stress and may lead to failures.

After printing the Front_case_hooks, I strongly recommend measuring them while attached to the case to confirm accuracy.

Hook contact faces with desk:

  • Non-locking: 25 mm deep × 42 mm wide

  • Locking: 25 mm deep × 50 mm wide
    (includes 2 mm clearance + 2 mm locking wall on each side)


Installation Notes & Safety Warnings

  • Do NOT overtighten the wood screws

  • Overtightening can introduce excessive stress

  • This may cause layer separation or cracking

  • Tighten only until the hook is firmly secured to the desk


Disclaimer

I take no responsibility for any damage to your property.
I am currently using this mount and it works well for me, but I cannot guarantee it will work safely in every setup.

Use your own discretion, verify your materials, desk construction, and installation accuracy, and only use this mount if you are confident it is suitable for your setup.

Tagi