1 / 4
Befiederungsgerät für 3 Vanes / Fletching Jig for 3 vanes — zdjęcie 1
1 / 4

Befiederungsgerät für 3 Vanes / Fletching Jig for 3 vanes

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Befiederungsgerät zum Befiedern von Schäften von 4,5mm bis 8mm / Fletching Jig for shafts from 4,5mm OD up to 8mm OD

Ocena
5 / 5
Polubienia
23
Pobrania
214
Wydruki
1
Wyświetlenia
818
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Sports
Licencja
Creative Commons — Attribution — Noncommercial

Für Schäfte von 4,5 bis 8mm Außendurchmesser
Man benötigt die base, eine cap mit dem Außendurchmesser des Schafts (nächste Größe) und drei Inserts mit dem gewünschten Winkel (0°, 1°, 1,5° oder 2°)
Der Bajonettverschluss funktioniert am besten, wenn der Zapfen und die Führung mit etwas Support gedruckt wird, siehe Abbildung

For shafts with an outer diameter of 4.5 to 8 mm
You will need the base, a cap with the outer diameter of the shaft (next size), and three inserts with the desired angle (0°, 1°, 1.5°, or 2°).
The bayonet fitting works best if the pin and guide are printed with some support as shown in the image.

Die senkrechte Vertiefung an der Basis zeigt die Position der Führungsfeder (90° zur Sehne).

Die Einsätze mit Winkel (1°, 1,5° und 2°) sind im STL jeweils für Links und Rechts enthalten. Im Slicer das STL in Objekte trennen, senkrecht stellen und die gewünschte Variante 3x ohne Support drucken.

The vertical indentation at the base indicates the position of the guide vane(90° to the string).

The inserts with angles (1°, 1.5°, and 2°) are included in the STL file for both left and right sides. In your slicer, split the STL file into objects, orient them vertically, and print the desired variant three times without supports.

Falls die Vanes nicht mit Sekundenkleber, sondern mit länger abbindenden Kleber befestigt werden, können die 3 Einsätze mit einem Gummiband fixiert werden.

27.12.25 Update zu den Einsätzen: Bei der Version 1.1 ist der Aufnahmespalt schmaler, sodass die Vanes strammer sitzen. Damit das nicht zu eng wird, ist dafür der vordere Teil verdünnt, um eine Flexibilität zu erzeugen, dies funktioniert sowohl mit PLA als auch mit PETG.

If the vanes are attached with a longer-setting adhesive instead of superglue, the three inserts can be secured with a rubber band.

December 27, 2025 Update on the inserts: In version 1.1, the mounting gap is narrower, resulting in a tighter fit for the vanes. To prevent this from becoming too tight, the front section has been thinned to allow for flexibility. This works with both PLA and PETG.

Gedruckt mit

  • PLA

  • 0.2mm

  • 2 Perimeter

  • 15% Infill

  • Infill Adaptiv Kubisch

Kommentare, Makes, Verbesserungsvorschläge und Änderungswünsche sind willkommen.

Printed with:

  • PLA 0.2mm

  • 2 Perimeters

  • 15% Infill

  • Adaptive Cubic Infill

Comments, builds, suggestions for improvement, and change requests are welcome.

Tagi