Fiesta Mk7 / Mk7.5 Card Slot MagSafe Phone Mount
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
MagSafe phone mount for Fiesta Mk7/7.5 using the unused card slot for a clean, factory-style install.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 11
- Wydruki
- 0
- Wyświetlenia
- 252
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Fiesta Mk7 / Mk7.5 Card Slot MagSafe Phone Mount
Description
The Ford Fiesta Mk7 and Mk7.5 offer very limited options for securely mounting a phone in a sensible, driver-friendly position. This becomes even more problematic when using a wireless CarPlay/Android Auto screen, as common suction mounts often conflict with screen placement.
On some Fiesta Mk7 / Mk7.5 models, there is an unused switch blank that includes a card slot. This design replaces that card slot cover with a purpose-built MagSafe phone mount, providing a clean, factory-style mounting location without obstructing visibility or controls.
This mount is designed specifically to work with the **ESR MagSafe Car Mount Charger**, reusing the charger’s front assembly while replacing the rear ball mount with the included printed component. Feel free to modify/remix, f3d/STEP files are provided.
Features
Utilizes an unused OEM card slot location (only on some trim variants)
Clean, integrated look with no windshield or dash suction mounts
Secure mounting with rear support to prevent pull-off when removing the phone
Designed for MagSafe charging
No permanent modification to the vehicle required
Vehicle Compatibility
Ford Fiesta Mk7
Ford Fiesta Mk7.5
*(Only vehicles with the unused card slot / switch blank in the dash)*
Printing Instructions
Print the part **in the orientation shown** in the preview images
Supports are required
Use a craft knife to carefully remove the support from the **print-in-place clips**
Install three **M3 heat-set inserts** into the provided holes
Recommended material:
- PETG or ABS (PLA may soften in hot interiors)
Assembly Instructions
Remove the dashboard trim
Video guide: https://www.youtube.com/watch?v=j1eZvobdqvoReplace the rear ball mount on the **ESR MagSafe Car Mount Charger** with the included printed rear mount
Assemble the MagSafe charger onto the **Card Slot MagSafe Phone Mount (Front)** using M3 screws
Replace the factory card slot cover with the assembled mount
Attach the printed rear support
Secure rear support using M3 screw
*(Rear support is essential to prevent the mount popping off when the phone is removed)*
Additional Hardware Required
ESR MagSafe Car Mount Charger- M3 heat-set inserts × 3
M3 × 10 mm cap head screws × 3
Example Setup (Shown in Photos)
For those curios of my full setup
CarPlay/Android Auto Screen: **Podofo A3247**
Audio Output: Phone Bluetooth directly into Ford Sync (screen audio bypassed)
Notes
This is a custom-fit part designed specifically for the Fiesta Mk7 / Mk7.5 dash layout
Fitment may vary slightly depending on trim level
Test fit before final assembly
Disclaimer
This product is a 3D-printed, aftermarket accessory and is **not an OEM Ford part**. Installation and use are entirely at the user’s own risk.
The designer and distributor accept **no responsibility or liability for accidents, injuries, loss, or damage** resulting from the installation or use of this mount or its derivatives, including (but not limited to):
- Driver distraction
- Device detachment while driving
- Interference with vehicle controls, safety equipment, or visibility
It is the user’s responsibility to ensure:
- The mount is securely installed before driving
- The phone does not obstruct the driver’s view or access to controls
- The phone is used in compliance with local driving and mobile device laws
Always prioritize safe driving and do not interact with the device while the vehicle is in motion