Roller Base for the "Holy Grail Filament Dry Box"
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This add-on converts the "Holy Grail Filament Dry Box" into a true closed-loop feeding system by adding rollers
- Ocena
- 0 / 5
- Polubienia
- 14
- Pobrania
- 37
- Wydruki
- 0
- Wyświetlenia
- 317
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial

Fully assembled internal roller base with filament spool
Overview
Internal filament roller base for the Holy Grail Dry Box.
Allows filament to feed directly from inside the sealed box while printing, without removing spools. Designed for the E1 Dryer version and compatible with the flat-bottom Dry Box.
Because internal space is extremely limited, several unconventional design decisions were required to make the system both compact and reliable.
Note: The roller needs the "Holy Grail Filament Dry Box" Extended Lids to have enough clearance to work.
Installed & In-Use View
When installed in the Dry Box, the roller base supports filament spools directly inside the sealed enclosure. Spool edges ride on either side of the supports to maintain alignment and prevent contact between spools.
Design Rationale

Fully assembled roller base
Most filament roller designs use 608 skateboard bearings, which require external end supports. That approach does not fit inside the Dry Box.
Instead, this design uses MR63-ZZ miniature bearings (3×6×2.5 mm) mounted in external printed supports, allowing the axle to sit extremely close to the box walls and maximizing usable spool width.
Trade-off:
This doubles the number of bearings required, but allows the system to fit inside the Dry Box while remaining smooth and reliable.
The Dry Box’s internal pylons are slightly off-center, so the roller base is intentionally offset to maintain proper centering. This affects print orientation, discussed later.
Desiccant Capacity

Roller base installed inside the Dry Boxes
The compact roller design allows for integrated loose desiccant storage:
Main base: 90+ g
Corner boxes: 30+ g each; 4x for 120 g
Plug box: 60+ g
Even without filling every container to the max, the total desiccant capacity can easily exceed 200 g.
Bill of Materials (BOM)
Required
MR63-ZZ Miniature Ball Bearings (3×6×2.5 mm) — 16
M3×8 mm hex head screws — 16
Optional
Loose desiccant or desiccant packets
Bearings are commonly available in packs of 20 for around $9 USD, leaving spares.
Printing Recommendations
Material
PETG recommended
Safe for use inside the dryer when drying PLA or PETG
For higher drying temperatures (ASA, etc.), print in a suitable material
Parts Overview

All printed parts for one roller base module
The roller system consists of:
Main base module
Front module
Back module
Base lid
Axles
Collars
Caps
Loose supports
Optional desiccant boxes
What to Print (Slicer Reference)
The included 3MF files are pre-oriented and grouped for convenience. Use the slicer views to confirm part selection and orientation before printing.
Supports & Print Settings
Front & Back Modules
Use Tree supports only
Normal supports will be extremely difficult to remove
Main Base
Normal supports only for the logo cutout
The cutout ensures the roller surface sits flat on the Dry Box floor
Axles
Supports optional, but recommended
If printed without supports, the cap recess must be cleaned manually
If knock-over occurs, use normal supports with a brim
Desiccant Boxes
No supports
Supports will be difficult or impossible to remove, especially for the plug box
Strength Settings (Important)
Axles
Wall loops: 15+
This makes the axle effectively solid, preventing long-term deformation under spool weight during drying
Uses more filament but significantly improves durability
Assembly Instructions
Bearing Installation
Insert the bearing into the printed supports, both loose and in the modules, and secure it with an M3 screw. To make things easier, use tweezers to insert bearings.
⚠ Important:
If resistance is felt while tightening, the screw may be pressing against the bearing. Stop, loosen slightly, and shake the module to center the bearing before continuing.
Axle Assembly
Steps:
File or sand the seam ridge on the Axle and Collar
Slide a Collar onto the Axle until it nearly touches the printed collar
Add a Loose Support (screw heads facing away from the collars)
Left and right versions exist — tops tilt toward the base center
Add a Cap to the non-printed-collar end
Insert the printed-collar end into the module support and cap it
Repeat for the second axle
Slide the Loose Supports into the guide rails
Guides are intentionally long for different spool widths
Slide Collars into the Loose Supports
Lift the axle slightly if needed
The support top should mostly cover the Collar
Be careful not to slide the Collars too far as to restrict the Axle's movement
Repeat for the second module

Axle and bearing installation: MR63-ZZ bearing secured with M3 screw.

Axle installed into module support: Printed collar inserts into the fixed bearing support

Both axles installed in the module: Loose supports slide in the guide rails to accommodate the spool
Cap note:
The default caps are easy to remove. For a more permanent cap, use
Axle-version-3-cap-lock-tight.stl
⚠ Warning: This version is extremely difficult to remove once installed.
Final Assembly

Completed roller base before installation: Front and back modules attached to the main base
Attach Front and Back modules to the Main Base
They are not interchangeable due to the Dry Box pylon offset
Optionally fill the desiccant from the center outward
Slide the Base Lid into place using the locking ridges
Install the base into the Dry Box with the “F” marking toward the monitor hole
If installed incorrectly, the base will not seat properly.
Spool Placement
Place spools so the edges rest on either side of the supports. This stabilizes feeding and prevents spools from contacting each other. Axle caps and the lid extension help maintain alignment.
Maintenance
No lubrication required (sealed bearings)
Only maintenance is drying the desiccant as needed
If using desiccant packets, the roller base never needs to be removed
Optional Desiccant Accessories
Corner boxes are interchangeable front/back
The plug fits only the rear air port
If there is a demand for it, I can convert the corner boxes to span the whole box for the flat-bottom version of the Dry Box, since you are losing the option to use the plug version of the desiccant box
Potential Updates
Integrate the corner desiccant boxes into the base. My original design called for this, but it causes problems that would need to be overcome
Update the desiccant boxes for the flat version of the Dry Box
Outro
I hope you find this add-on useful.
Happy printing! 🖨
Updates
Apr 16, 2026 - Added missing loose axle support STL. It was in the 3MF, but not as a separate file.