1 / 13
Roller Base for the "Holy Grail Filament Dry Box" — image 1
1 / 13

Roller Base for the "Holy Grail Filament Dry Box"

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

This add-on converts the "Holy Grail Filament Dry Box" into a true closed-loop feeding system by adding rollers

Rating
0 / 5
Likes
14
Downloads
37
Makes
0
Views
317
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial

Fully assembled internal roller base with filament spool

Overview 

Internal filament roller base for the Holy Grail Dry Box. 

Allows filament to feed directly from inside the sealed box while printing, without removing spools. Designed for the E1 Dryer version and compatible with the flat-bottom Dry Box.

Because internal space is extremely limited, several unconventional design decisions were required to make the system both compact and reliable.

Note: The roller needs the "Holy Grail Filament Dry Box" Extended Lids to have enough clearance to work.


Installed & In-Use View

When installed in the Dry Box, the roller base supports filament spools directly inside the sealed enclosure. Spool edges ride on either side of the supports to maintain alignment and prevent contact between spools.


Design Rationale

Fully assembled roller base

Most filament roller designs use 608 skateboard bearings, which require external end supports. That approach does not fit inside the Dry Box.

Instead, this design uses MR63-ZZ miniature bearings (3×6×2.5 mm) mounted in external printed supports, allowing the axle to sit extremely close to the box walls and maximizing usable spool width.

Trade-off:
This doubles the number of bearings required, but allows the system to fit inside the Dry Box while remaining smooth and reliable.

The Dry Box’s internal pylons are slightly off-center, so the roller base is intentionally offset to maintain proper centering. This affects print orientation, discussed later.


Desiccant Capacity

Roller base installed inside the Dry Boxes

The compact roller design allows for integrated loose desiccant storage:

  • Main base: 90+ g

  • Corner boxes: 30+ g each; 4x for 120 g

  • Plug box: 60+ g

Even without filling every container to the max, the total desiccant capacity can easily exceed 200 g.


Bill of Materials (BOM)

Required

  • MR63-ZZ Miniature Ball Bearings (3×6×2.5 mm) — 16

  • M3×8 mm hex head screws — 16

Optional

  • Loose desiccant or desiccant packets

Bearings are commonly available in packs of 20 for around $9 USD, leaving spares.


Printing Recommendations

Material

  • PETG recommended

    • Safe for use inside the dryer when drying PLA or PETG

  • For higher drying temperatures (ASA, etc.), print in a suitable material


Parts Overview

All printed parts for one roller base module

The roller system consists of:

  • Main base module

  • Front module

  • Back module

  • Base lid

  • Axles

  • Collars

  • Caps

  • Loose supports

  • Optional desiccant boxes


What to Print (Slicer Reference)

The included 3MF files are pre-oriented and grouped for convenience. Use the slicer views to confirm part selection and orientation before printing.


Supports & Print Settings

Front & Back Modules
  • Use Tree supports only

  • Normal supports will be extremely difficult to remove

Main Base
  • Normal supports only for the logo cutout

  • The cutout ensures the roller surface sits flat on the Dry Box floor

Axles
  • Supports optional, but recommended

  • If printed without supports, the cap recess must be cleaned manually

  • If knock-over occurs, use normal supports with a brim

Desiccant Boxes
  • No supports

  • Supports will be difficult or impossible to remove, especially for the plug box


Strength Settings (Important)

Axles

  • Wall loops: 15+

  • This makes the axle effectively solid, preventing long-term deformation under spool weight during drying

  • Uses more filament but significantly improves durability


Assembly Instructions

Bearing Installation

Insert the bearing into the printed supports, both loose and in the modules, and secure it with an M3 screw. To make things easier, use tweezers to insert bearings.

⚠ Important:
If resistance is felt while tightening, the screw may be pressing against the bearing. Stop, loosen slightly, and shake the module to center the bearing before continuing.


Axle Assembly

Steps:

  1. File or sand the seam ridge on the Axle and Collar

  2. Slide a Collar onto the Axle until it nearly touches the printed collar

  3. Add a Loose Support (screw heads facing away from the collars)

    • Left and right versions exist — tops tilt toward the base center

  4. Add a Cap to the non-printed-collar end

  5. Insert the printed-collar end into the module support and cap it

  6. Repeat for the second axle

  7. Slide the Loose Supports into the guide rails

    • Guides are intentionally long for different spool widths

  8. Slide Collars into the Loose Supports

    • Lift the axle slightly if needed

    • The support top should mostly cover the Collar

    • Be careful not to slide the Collars too far as to restrict the Axle's movement

  9. Repeat for the second module

Axle and bearing installation: MR63-ZZ bearing secured with M3 screw.

Axle installed into module support: Printed collar inserts into the fixed bearing support

Both axles installed in the module: Loose supports slide in the guide rails to accommodate the spool 

Cap note:
The default caps are easy to remove. For a more permanent cap, use

  • Axle-version-3-cap-lock-tight.stl

⚠ Warning: This version is extremely difficult to remove once installed.


Final Assembly

Completed roller base before installation: Front and back modules attached to the main base

  1. Attach Front and Back modules to the Main Base

    • They are not interchangeable due to the Dry Box pylon offset

  2. Optionally fill the desiccant from the center outward

  3. Slide the Base Lid into place using the locking ridges

  4. Install the base into the Dry Box with the “F” marking toward the monitor hole

If installed incorrectly, the base will not seat properly.


Spool Placement

Place spools so the edges rest on either side of the supports. This stabilizes feeding and prevents spools from contacting each other. Axle caps and the lid extension help maintain alignment.


Maintenance

  • No lubrication required (sealed bearings)

  • Only maintenance is drying the desiccant as needed

  • If using desiccant packets, the roller base never needs to be removed


Optional Desiccant Accessories

  • Corner boxes are interchangeable front/back

  • The plug fits only the rear air port

  • If there is a demand for it, I can convert the corner boxes to span the whole box for the flat-bottom version of the Dry Box, since you are losing the option to use the plug version of the desiccant box


Potential Updates

  • Integrate the corner desiccant boxes into the base. My original design called for this, but it causes problems that would need to be overcome

  • Update the desiccant boxes for the flat version of the Dry Box


Outro

I hope you find this add-on useful.
Happy printing! 🖨


Updates

Apr 16, 2026 - Added missing loose axle support STL. It was in the 3MF, but not as a separate file.

Tags