1 / 11
TP-Link TL-SX1008 Silent Fan Mod – 120mm Top Mount — zdjęcie 1
1 / 11

TP-Link TL-SX1008 Silent Fan Mod – 120mm Top Mount

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Ultra-quiet 120mm top fan mod for the TP-Link TL-SX1008, improving airflow while drastically reducing noise.

Ocena
0 / 5
Polubienia
0
Pobrania
7
Wydruki
0
Wyświetlenia
163
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Office
Licencja
Creative Commons — Attribution — Share Alike

The TP-Link TL-SX1008 is an excellent 10 GbE switch, but its stock cooling solution is extremely noisy for home or office environments.
Even after replacing the original fan with a smaller 40 mm quiet fan, the noise reduction is still limited due to airflow constraints.

This mod solves the problem by replacing the internal fan concept with a top-mounted 120 mm fan, allowing very low RPM operation, excellent airflow, and near-silent performance.

Key Features

  • Designed specifically for the TP-Link TL-SX1008

  • Top-mounted 120 mm fan adapter

  • Drastic noise reduction compared to stock and 40 mm fan mods

  • Maintains safe operating temperatures

  • Magnetic mounting system (no permanent modification to the printed parts)

  • Easy fan removal for maintenance

Tested Setup

  • Fan: 120 mm (tested with Noctua NF-A12x25)

  • Noise reduction: Low-noise adapter (tested with NA-SRC7 / ~7 V)

  • Magnets: Neodymium disc magnets 5 mm × 3 mm

  • Mounting: 3M double-sided tape (adapter to metal cover)

Any high-quality 120 mm fan can be used. The fan and voltage reduction solution are user-selectable.

Important Notes

  • This mod requires cutting the metal top cover of the switch.

  • The switch will have a top opening — recommended for clean or enclosed environments.

  • Perform this mod at your own risk.

  • This is not an official TP-Link modification.

Results

After the mod, the switch becomes virtually silent, even in quiet rooms, while maintaining very good thermal performance.
This makes the TL-SX1008 finally suitable for homelabs, offices, and living spaces.

___________________________________________________________________________________________________________________

Step-by-step (Photos 01–11)

Photo 01 – The problem (stock switch noise)

The TP-Link TL-SX1008 is great, but the stock fan is extremely loud, especially for a home/office or homelab environment.

Photo 02 – First attempt: 40 mm fan swap (partial improvement)

I first followed the common community mod and replaced the original fan with a quieter 40 mm fan:

  • Noctua NF-A4x20 FLX (12V / 0.06A)

This helps, but in my case the switch was still too noisy, and the reduction was far from “silent”.

Photo 03 – Planning the top cut (positioning)

I decided to move to a different approach: a top-mounted 120 mm fan, running at reduced voltage for near-silent operation.

To choose the cut position, I used two references:

  1. The location of the main heatsink (most important cooling target)

  2. The position of the fan connector, so I could still plug the fan in internally

The final cut position ended up slightly offset (more lateral than centered), but it allowed the cable routing and connection.

Photo 04 – Marking the cut using the printed part as a template

I placed the printed adapter on the top cover and used it as a cutting guide to mark the exact outline.

Photo 05 – Cutting the metal top cover

I used a rotary tool (Dremel / micro grinder) to cut the top cover along the marked outline.
This step is the “messy” part, but if you’re used to basic modding, it’s straightforward.

Photo 06 – Installing the magnets (watch the polarity)

The adapter uses neodymium magnets to position/attach the fan frame cleanly.

Magnets used:

  • Neodymium disc magnets 5 mm × 3 mm

Important: pay attention to polarity so the parts attract each other (and don’t repel).

Photo 07 & 08 – Fixing the adapter to the metal cover

I applied 3M double-sided tape to the underside of the adapter (the part that stays on the switch cover), then carefully aligned it and pressed it into place over the cutout.

Photos 09, 10 & 11 – Fan installation, wiring and final result

I installed the 120 mm fan on the printed adapter using anti-vibration mounts (in my case, the original Noctua rubber mounts, but screws or other mounting methods work as well).

Fan used (because I already had it available):

  • Noctua NF-A12x25
    Any good-quality 120 mm fan can be used.

Next, I routed the fan cable and connected it to the internal fan header.
This step requires a bit of patience due to limited internal space, but it is absolutely doable (an extension cable may help).

After final assembly, the noise issue was completely solved — the switch became virtually silent, while temperatures remained very good.

Since the top cover now has an opening, this mod is recommended for use in a clean environment, ideally inside a cabinet, rack, or enclosed space. In my case, the switch is installed in a closed environment, so dust was not a concern.

UPDATE - 19-02-2025

Update – External Power Solution & New Model Version

After several days of real-world use, I experienced intermittent fan shutdowns when powering the 120 mm fan directly from the switch’s internal fan header.

Instead of continuing to troubleshoot the internal header, I switched to an external power supply for the fan.

Physical Modification

Since my switch was already fully assembled, I used a drill to create a clean cable pass-through hole in the metal housing to route the external power cable.

To make things easier for future builders, I redesigned the printed top adapter.

There is now a second version of the model:  Top Fan – External Power Version

Important Reminder

This modification:

  • Requires cutting the top metal cover

  • Voids warranty

  • Is not beginner-friendly

  • Is intended for users comfortable with permanent hardware modification

This mod is for those who prioritize silence above originality.

In my case, the result is absolutely worth it — the TL-SX1008 is now virtually silent and fully stable.

Tagi