WKMU V1 | Speedy Klipper MMU | PLA TPU PETg | 20 second reloads | built for voron/eva2.4 toolhead
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
WKMU is compatible with every Klipper printer with DDE. Automatic purge calculation. It's great if you like tinkering.
- Ocena
- 0 / 5
- Polubienia
- 30
- Pobrania
- 56
- Wydruki
- 0
- Wyświetlenia
- 823
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Overview:
First of all, feel free to ask questions and leave sugestions what to add to the MMU/instructions.
I built WKMU based on the working principles of AMS Lite (Didn't know that at the time).
It uses 4 secondary stage extruders that sync with the main one.
The filament is stored in ptfe tubes just above the toolhead.
It has 4 built in filament sensors and runout logic, will be working on automatic swapping for same color spools. The swaps take about ~25 seconds in the current iteration. The most swaps per print i did was about 500 so its reliable enough.
YouTube video
IMPORTANT:
The makros are optimised for Orbiter2.5 + Phaetus Rapido HF. PLA/PETg/TPU 96A.
Updates List:
25.04.2026
Reduced needless retraction after swap. Helps retain filament preasure in small details printed immidiately after swap.
22.03.2026:
BugFixes
19.03.2026:
Changed the filament makros so it's easier to change filaments.
Now you just have to change the type of the plastic and the rest of the settings will be changed automatically.Introduced Makro presets for PETG/PETGCF and TPU 96A
Now when changing filament the nozzle will automatically change the temperature acording to configs.
EXAMPLE PRINTS




Unfortunate Layer shifts caused by the STL model :((






Parts list:
Parts:
2X 370mm 2020 slot
1X Mellow Fly MMU board (swap for something cheaper if you wish, but it will require software and config changes)
4X TP2209 stepper motor drivers with ARGB LEDS (the price is basically the same)
4X Nema17 stepper motor
16X 8x8x22 ball bearing
8X 90mm 8mm diameter metal pipe/rod
8X 2.5x5x8 ball bearing
4X 20x5mm steel pins
8X 11mm diameter 5mm shaft extruder gears
1X Blue threadlock/screw glue
6mm inside diameter spring cut to length
2.5mm id 4mm od ptfe tube (depends on you)
4X micro switch (without lever/you can break it off)
4X 6mm BB (Airsoft Ball)/bearing ball
4X Nema17 heatsink (optional)
1X 24V PSU 215 x 115 x 30 mm formfactor (you can also pull the power from your printer)
Cable for microswitches
4X Threaded heat insert 4x4x6mm (inner/depth/outer)
Screws and nuts:
16X M3x30mm INTERNAL HEX
8X M3x40
8X M5x20
10X M5x10
8X M2.5x4
26X M5 T-nut
16X M5x10 FLAT HEAD
4X M4x10 FLAT HEAD
4X M4x35 HEX HEAD
4X M4x1 washers
4X 8mm long computer threaded standoff (the inside thread is 3mm and outside 3.5mm)
You will also need a 4-> 1 ptfe splitter, it's on my profile.
And a some kind of poop chute, you have to build your own.
The printer has to purge somewhere. :(
Print instructions:
You can print all the parts in any stiff material. I used PETG-cf, but from my testing, even PLA will do.
Extruder parts:
AlignTool; ScrewTop; VSlotHolder; FrontCover:
0.2mm layers
0.25mm first layer
20% infill
No supports neededLever:
Print on the broadest part laying down
0.2mm layers
0.25mm first layer
40% infill
Add supports on the horizontal overhangMotorPlate:
Print laying down
0.15mm layers
40% infill
Add supports on two horizontal overhangPTFEClamp1
0.15mm layers
Add supports on the insidePTFEClamp2
0.15mm layers
No supports needed
Body parts:
SideCover:
0.3mm layers
30% infill
support onThe rest of parts:
0.3mm layers
30% infill
No supports needed
Assembly instructions:
Wiring

Extruders
Insert the threaded insert into the stepper plate with a soldering iron.

Insert the BB into the Stepperplate. It can be quite hard, but after it finds its place it should just drop and have a lot of room.

Insert the micro switch into the stepper plate. (You have to have it already soldered.) It will be hard because the mounting is friction fit.

Mount the first extruder gear on the nema 17 motor. Position it using the provided tool. Use a dab of threadlock to keep the gear from sliding.

Position the stepper plate on the motor.

Press the 2.5mm ball bearings into the lever.

Press in the stell pin. (REMEMBER TO PUT THE EXSTRUDER GEAR IN THE SHOWN ORIENTATION)

Screw in 2 M3x35 screws into those two holes. (they stiffen the lever and prevent creep)

Position the lever onto the stepper plate.

Place the stepper cover onto this assembly.

Screw in M3X30mm screws.

Screw in the M4x35 screw with the spring cut to length and the handle on top.

Screw in the extruder v-slot holder using two M5x20 screws.

You assembled your extruder... Now do it 3 more times.
Body
Skip steps 1 and 2 if you won't use aditional PSU.
Screw the M4x10 flat head screws into the PSU and the v-slot holders.
Mount the PSU using t-nuts and M5x10 flat head screws onto 2020 v-slots.

Mount the remaining v-slot holders in the same manner.

Press the 22mm bearings into the filament rollers. Do it 8 times (one has aditional space for mounting the control board).

Cut the 8mm metal pipe into 8 9cm parts
Mount all the parts using M5x10 screws and t-nuts onto the v-slots.
If metal pipes move linearly you can add a dab of threadlock between them and the bearing.
BE CAUTIOUS, THE THREADLOCK CAN KILL THE BEARING WHEN NOT USED PROPPERLY
Mount the extruders using M5x10 screws and t-nuts

Plug in the extruder cables and tidy them in the compartment here:

Screw in the standoffs.

Connect all the cables to the mmu board (ALSO THE POWER CABLE).
Extruders should be connected like so:
The closest extruder to the left-most controller, the second closest to the second and so on.Positon the board on the standoffs.

Screw in the shround using 4 M3x30 screws.

Now you have the mmu body and extrudes built.

PTFE instalation
Put the PTFE clamp onto the tube.

Insert the tube into the extruder.

Screw the M2.5 screws into the extruder.

Screw in the second part of the holder.

Now your PTFE tubes are secured
Splitter
Just insert the tubes into the splitter, you can find it on my profile.

https://www.printables.com/model/1609499-ultra-low-angle-ptfe-splitter
Filament poop ramp
Work in progress.
Config file instalation and configuration:
Wire the board like so:
https://mellow.klipper.cn/en/docs/ProductDoc/ToolBoard/fly-mmu/mmu/wiring
Instalation:
You just have to copy the contents of printer.txt into your printer.cfg file (at the end of it DO NOT CLEAR YOUR printer.cfg FILE). You might need to change the boards directory though.
Install klipper on Mellow fly mmu after that, there you can also get info on how to setup it.
Tutorial:https://mellow.klipper.cn/en/docs/ProductDoc/ToolBoard/fly-mmu/mmu/flash/
Import all the files into your system (loading.cfg;filaments.cfg;makros.cfg).
Create a variables.cfg file (empty).
Configuration:
makros.cfg
In the Toolchange makro change:
G1 X225 Y195 F24000
to match where your tollhead docks for purging the filament.
In the Wiggle makro change the movement to match where your cleaning brush is positioned.
filaments.cfg
variable_filament_type: {-1:"NONE",0:"PLA",1:"PLA",2:"PLA",3:"PLA"}loading variables driven by the array above
variable_loading_speed: {"NONE":0,"PETG":9000,"PLA":9000,"TPU":1000}
variable_max_purge_speed: {"NONE":0,"PETG":500 ,"PLA":450 ,"TPU":200}
variable_cool_zone_speed: {"NONE":0,"PETG":7200,"PLA":7200,"TPU":7200}
variable_printing_temperature: {"NONE":0,"PETG":245 ,"PLA":215 ,"TPU":225}
variable_additional_lenght: {"NONE":0,"PETG":0 ,"PLA":0 ,"TPU":12.5}
You have to create a new preset if you want to add a new type of plastic, but if it's already on the list, you can just change the name in filament_type variable.
loading.cfg
The makros are prepared for 0.4mm copper zinc plated nozzle.
If you are not using Phaetus rapido hf + orbiter 2.5 you'll have to change this block:
G4 P2500 # Temperature soak
G1 E15 F{printer["gcode_macro FILAMENT"].max_purge_speed[printer["gcode_macro FILAMENT"].filament_type[slot]]} #Prime for unload, the heating chamber is ~15mm of length
#-----------------------------------------------------------------------------------------------------------------------
# Unload
G1 E-0.6 F3600 # this preasure bleed creates plugs but decreases the prominence of tails
G1 E-39.4 F{printer["gcode_macro FILAMENT"].cool_zone_speed[printer["gcode_macro FILAMENT"].filament_type[slot]]} #unload into the cool zone
#---------full into-a-tube retract
G4 P1500 # cooldown
G1 E-150 F{printer["gcode_macro FILAMENT"].loading_speed[printer["gcode_macro FILAMENT"].filament_type[slot]]}
G1 E-{printer["gcode_macro FILAMENT"].additional_lenght[printer["gcode_macro FILAMENT"].filament_type[slot]]} F{printer["gcode_macro FILAMENT"].loading_speed[printer["gcode_macro FILAMENT"].filament_type[slot]]}to match your hotend and main extruder.
You can tweak the values at line 175 if you see any colorbleed.
{% set purge_length = 15 + color_distance_rounded20 + starting_darkness40%}
The three integers represent the starting value, amout of mm per color distance, and amount of added mm for darkness of the unloaded filament.
Change those values to set maximal and minimal purge values
{% if purge_length<30 %}
{% set purge_length = 30%}
{% endif %}
{% if purge_length>70 %}
{% set purge_length = 70%}
{% endif %}Makros usage
Save_filament_A/B/C/D
Lets you change the colour of your filaments in RGB values 0-255.Mmmu_unload
Unloads the mmu withouth toolhead movement.Load_filament
Loads the mmu without toolhead movementLeds_off/on
Changes the power state of LEDS
Slicer settings (ORCA SLICER):
Printer -> Extruder1 -> Retraction in switching material: 1.05 mm
Printer -> Multimaterial -> Single Extruder Multi Material: true
Printer -> Machine G-code -> Change filament:
G91
G1 Z0.4
G90First use
Make sure you configured all the importand tidbits correctly and the printer boots up normally.
Check if all of the filament detection switches show up in your GUI.
Insert the filaments into the tubes and test if the states turn to 'Detected'.
Run all the Save_filament_A/B/C/D makros to save your filament colours. IMPORTANT It's needed to initialize the variables.
load filament
Use one of the T codes to initiate the loading of a filament.
Using G1 commands/GUI to push the filament into the hotend and purge it.
Run the next T makro. the filament will now move to its propper position in the tube.
Repeat the steps for all the filaments.