1 / 6
WKMU V1 | Speedy Klipper MMU | PLA TPU PETg | 20 second reloads | built for voron/eva2.4 toolhead — image 1
1 / 6

WKMU V1 | Speedy Klipper MMU | PLA TPU PETg | 20 second reloads | built for voron/eva2.4 toolhead

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

WKMU is compatible with every Klipper printer with DDE. Automatic purge calculation. It's great if you like tinkering.

Rating
0 / 5
Likes
30
Downloads
56
Makes
0
Views
823
Reviews
0

Updated at source:

Model information

License
Creative Commons — Attribution — Noncommercial — Share Alike

Overview:

First of all, feel free to ask questions and leave sugestions what to add to the MMU/instructions.

I built WKMU based on the working principles of AMS Lite (Didn't know that at the time).
It uses 4 secondary stage extruders that sync with the main one.
The filament is stored in ptfe tubes just above the toolhead.
It has 4 built in filament sensors and runout logic, will be working on automatic swapping for same color spools. The swaps take about ~25 seconds in the current iteration.  The most swaps per print i did was about 500 so its reliable enough.
YouTube video

IMPORTANT:
The makros are optimised for Orbiter2.5 + Phaetus Rapido HF. PLA/PETg/TPU 96A.

Updates List:

  • 25.04.2026

    • Reduced needless retraction after swap. Helps retain filament preasure in small details printed immidiately after swap.

  • 22.03.2026:

    • BugFixes

  • 19.03.2026:

    • Changed the filament makros so it's easier to change filaments.
      Now you just have to change the type of the plastic and the rest of the settings will be changed automatically.

    • Introduced Makro presets for PETG/PETGCF and TPU 96A

    • Now when changing filament the nozzle will automatically change the temperature acording to configs.

EXAMPLE PRINTS

Unfortunate Layer shifts caused by the STL model :((


Parts list:

Parts:
  • 2X 370mm 2020 slot

  • 1X Mellow Fly MMU board (swap for something cheaper if you wish, but it will require software and config changes)

  • 4X TP2209 stepper motor drivers  with ARGB LEDS (the price is basically the same)

  • 4X Nema17 stepper motor

  • 16X 8x8x22 ball bearing

  • 8X 90mm 8mm diameter metal pipe/rod

  • 8X 2.5x5x8 ball bearing 

  • 4X 20x5mm steel pins

  • 8X 11mm diameter 5mm shaft extruder gears

  • 1X Blue threadlock/screw glue

  • 6mm inside diameter spring cut to length

  • 2.5mm id 4mm od ptfe tube (depends on you)

  • 4X micro switch (without lever/you can break it off)

  • 4X 6mm BB (Airsoft Ball)/bearing ball

  • 4X Nema17 heatsink (optional)

  • 1X 24V PSU 215 x 115 x 30 mm formfactor (you can also pull the power from your printer)

  • Cable for microswitches

  • 4X Threaded heat insert 4x4x6mm (inner/depth/outer)

Screws and nuts:
  • 16X M3x30mm INTERNAL HEX

  • 8X M3x40

  • 8X M5x20

  • 10X M5x10

  • 8X M2.5x4 

  • 26X M5 T-nut

  • 16X M5x10 FLAT HEAD

  • 4X M4x10 FLAT HEAD

  • 4X M4x35 HEX HEAD

  • 4X M4x1 washers

  • 4X 8mm long computer  threaded standoff (the inside thread is 3mm and outside 3.5mm)

You will also need a 4-> 1 ptfe splitter, it's on my profile.
And a some kind of poop chute, you have to build your own.
The printer has to purge somewhere. :(

Print instructions:

You can print all the parts in any stiff material. I used PETG-cf, but from my testing, even PLA will do.

Extruder parts:
  • AlignTool; ScrewTop; VSlotHolder; FrontCover:
    0.2mm layers
    0.25mm first layer
    20% infill
    No supports needed

  • Lever:
    Print on the broadest part laying down
    0.2mm layers
    0.25mm first layer
    40% infill
    Add supports on the horizontal overhang

  • MotorPlate:
    Print laying down
    0.15mm layers
    40% infill
    Add supports on two horizontal overhang

  • PTFEClamp1
    0.15mm layers
    Add supports on the inside

  • PTFEClamp2
    0.15mm layers
    No supports needed

Body parts:
  • SideCover:
    0.3mm layers
    30% infill
    support on

  • The rest of parts:
    0.3mm layers
    30% infill
    No supports needed

Assembly instructions:

Wiring
Extruders
  1. Insert the threaded insert into the stepper plate with a soldering iron.

  2. Insert the BB into the Stepperplate. It can be quite hard, but after it finds its place it should just drop and have a lot of room.

  3. Insert the micro switch into the stepper plate. (You have to have it already soldered.) It will be hard  because the mounting is friction fit.

  4. Mount the first extruder gear on the nema 17 motor. Position it using the provided tool. Use a dab of threadlock to keep the gear from sliding.

  5. Position the stepper plate on the motor.

  6. Press the 2.5mm ball bearings into the lever.

  7. Press in the stell pin. (REMEMBER TO PUT THE EXSTRUDER GEAR IN THE SHOWN ORIENTATION)

  8. Screw in 2 M3x35 screws into those two holes. (they stiffen the lever and prevent creep)

  9. Position the lever onto the stepper plate.

  10. Place the stepper cover onto this assembly.

  11. Screw in M3X30mm screws.

  12. Screw in the M4x35 screw with the spring cut to length and the handle on top.

  13. Screw in the extruder v-slot holder using two M5x20 screws.

  14. You assembled your extruder... Now do it 3 more times.

Body
  1. Skip steps 1 and 2 if you won't use aditional PSU.
    Screw the M4x10 flat head screws into the PSU and the v-slot holders.

  2. Mount the PSU using t-nuts and M5x10 flat head screws onto 2020 v-slots.

  3. Mount the remaining v-slot holders in the same manner.

  4. Press the 22mm bearings into the filament rollers. Do it 8 times (one has aditional space for mounting the control board).

  5. Cut the 8mm metal pipe into 8 9cm parts

  6. Mount all the parts using M5x10 screws and t-nuts onto the v-slots.
    If metal pipes move linearly you can add a dab of threadlock between them and the bearing. 
    BE CAUTIOUS, THE THREADLOCK CAN KILL THE BEARING WHEN NOT USED PROPPERLY

  7. Mount the extruders using M5x10 screws and t-nuts

  8. Plug in the extruder cables and tidy them in the compartment here:

  9. Screw in the standoffs.

  10. Connect all the cables to the mmu board (ALSO THE POWER CABLE).
    Extruders should be connected like so:
    The closest extruder to the left-most controller, the second closest to the second and so on.

  11. Positon the board on the standoffs.

  12. Screw in the shround using 4 M3x30 screws.

  13. Now you have the mmu  body and extrudes built.

PTFE instalation
  1. Put the PTFE clamp onto the tube.

  2. Insert the tube into the extruder.

  3. Screw the M2.5 screws into the extruder.

  4. Screw in the second part of the holder.

  5. Now your PTFE tubes are secured

Splitter
  1. Just insert the tubes into the splitter, you can find it on my profile.

    https://www.printables.com/model/1609499-ultra-low-angle-ptfe-splitter

Filament poop ramp

Work in progress.

Config file instalation and configuration:

Wire the board like so:
https://mellow.klipper.cn/en/docs/ProductDoc/ToolBoard/fly-mmu/mmu/wiring

Instalation:
You just have to copy the contents of printer.txt into your printer.cfg file (at the end of it DO NOT CLEAR YOUR printer.cfg FILE). You might need to change the boards directory though.
Install klipper on Mellow fly mmu after that, there you can also get info on how to setup it.
Tutorial:https://mellow.klipper.cn/en/docs/ProductDoc/ToolBoard/fly-mmu/mmu/flash/

Import all the files into your system (loading.cfg;filaments.cfg;makros.cfg).
Create a variables.cfg file (empty).

Configuration:

makros.cfg
In the Toolchange makro change:
G1 X225 Y195 F24000
to match where your tollhead docks for purging the filament.

In the Wiggle makro change the movement to match where your cleaning brush is positioned.

filaments.cfg

variable_filament_type: {-1:"NONE",0:"PLA",1:"PLA",2:"PLA",3:"PLA"}

loading variables driven by the array above

variable_loading_speed: {"NONE":0,"PETG":9000,"PLA":9000,"TPU":1000} variable_max_purge_speed: {"NONE":0,"PETG":500 ,"PLA":450 ,"TPU":200} variable_cool_zone_speed: {"NONE":0,"PETG":7200,"PLA":7200,"TPU":7200} variable_printing_temperature: {"NONE":0,"PETG":245 ,"PLA":215 ,"TPU":225} variable_additional_lenght: {"NONE":0,"PETG":0 ,"PLA":0 ,"TPU":12.5}

You have to create a new preset if you want to add a new type of plastic, but if it's already on the list, you can just change the name in filament_type variable.

loading.cfg
The makros are prepared for 0.4mm copper zinc plated nozzle.
If you are not using Phaetus rapido hf + orbiter 2.5 you'll have to change this block:

G4 P2500    # Temperature soak
            G1 E15 F{printer["gcode_macro FILAMENT"].max_purge_speed[printer["gcode_macro FILAMENT"].filament_type[slot]]}  #Prime for unload, the heating chamber is ~15mm of length
            #-----------------------------------------------------------------------------------------------------------------------
            # Unload
            G1 E-0.6 F3600                  # this preasure bleed creates plugs but decreases the prominence of tails
            G1 E-39.4 F{printer["gcode_macro FILAMENT"].cool_zone_speed[printer["gcode_macro FILAMENT"].filament_type[slot]]}                 #unload into the cool zone
            #---------full into-a-tube retract
            G4 P1500                        # cooldown
            G1 E-150 F{printer["gcode_macro FILAMENT"].loading_speed[printer["gcode_macro FILAMENT"].filament_type[slot]]} 
            G1 E-{printer["gcode_macro FILAMENT"].additional_lenght[printer["gcode_macro FILAMENT"].filament_type[slot]]} F{printer["gcode_macro FILAMENT"].loading_speed[printer["gcode_macro FILAMENT"].filament_type[slot]]}

to match your hotend and main extruder.
You can tweak the values at line 175 if you see any colorbleed.
{% set purge_length = 15 + color_distance_rounded20 + starting_darkness40%}
The three integers represent the starting value, amout of mm per color distance, and amount of added mm for darkness of the unloaded filament.
Change those values to set maximal and minimal purge values

                    {% if purge_length<30 %}
                        {% set purge_length = 30%}
                    {% endif %}
                    {% if purge_length>70 %}
                        {% set purge_length = 70%}
                    {% endif %}

Makros usage

  1. Save_filament_A/B/C/D
    Lets you change the colour of your filaments in RGB values 0-255.

  2. Mmmu_unload
    Unloads the mmu withouth toolhead movement.

  3. Load_filament
    Loads the mmu without toolhead movement

  4. Leds_off/on
    Changes the power state of LEDS

Slicer settings (ORCA SLICER):

Printer -> Extruder1 -> Retraction in switching material: 1.05 mm
Printer -> Multimaterial -> Single Extruder Multi Material: true
Printer -> Machine G-code -> Change filament:

G91
G1 Z0.4 
G90

First use

  1. Make sure you configured all the importand tidbits correctly and the printer boots up normally.

  2. Check if all of the filament detection switches show up in your GUI.

  3. Insert the filaments into the tubes and test if the states turn to 'Detected'.

  4. Run all the Save_filament_A/B/C/D makros to save your filament colours. IMPORTANT It's needed to initialize the variables.

  5. load filament

    1. Use one of the T codes to initiate the loading of a filament.

    2. Using G1 commands/GUI to push the filament into the hotend and purge it.

    3. Run the next T makro. the filament will now move to its propper position in the tube.

    4. Repeat the steps for all the filaments.

Tags