1 / 11
TPU Lid Gasket for @GunplaMark's Filament Storage 2026 — zdjęcie 1
1 / 11

TPU Lid Gasket for @GunplaMark's Filament Storage 2026

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

TPU 85A or 95A Lid Gasket for @GunplaMark's Filament Storage 2026 drybox - replaces purchased 3mm Silicone foam cord

Ocena
5 / 5
Polubienia
84
Pobrania
328
Wydruki
6
Wyświetlenia
1673
Oceny
9

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
GNU General Public License v2.0

This TPU Lid Gasket for the Filament Storage 2026 drybox is a 3D-printed option to replace the 3mm Silicone foam cord that must be purchased and custom-sized to seal the lid on Mark's new drybox. This TPU Lid Gasket must be printed in 85A - 95A (or softer) TPU filament.

UPDATE 26 FEB 2026: Thanks to a successful print using Sunlu 95A TPU by @Jfassino_2030196 and my subsequent verification, this design can be printed with Shore 95A TPU using a 0.4mm nozzle!  Thank you, Jim, for informing me about this option!  I have added 2 new 3MF files (they have "0_4noz" in the filename) for use with 95A TPU and a 0.4mm nozzle.

I used Bambu Lab 85A TPU with a 0.6mm nozzle as well as Giantarm 95A TPU with a 0.4mm nozzle - printed on a textured PEI build plate with Kores glue stick applied.

Unless you're experienced with TPU printing and have a process that works well, I strongly recommend using a textured PEI build plate with some kind of glue stick due to TPU's desire to remain permanently stuck on any surface on which it's printed! A 0.6mm nozzle and a fairly direct path from the filament spool to the extruder may be needed if using 85A TPU (due to the stretchiness of 85A TPU).  A 0.4mm nozzle should be used if printing in 95A TPU.

I also recommend that you use the provided 3MF files because they ensure that the TPU Lid Gasket is a HOLLOW TUBE - which is necessary for this design to function properly. These 3MF files modify the following settings to ensure correct printing:

1 - Vertical shells Perimeters (Wall loops) = 1

2 - Infill Fill density (Sparse infill density) = 0%

3 - Top shell layers = 2

4 - Bottom shell layers = 2

5 - Seam position = Random

Though the TPU Lid Gasket will appear to be solid when fully printed, in order to compress properly, it must internally look like the following cut-away photo:

Once you've printed your TPU Lid Gasket, simply push it into the slot around the outside of Mark's Lid. As with the Silicone foam cord, you need to press the cereal container and the Lid together firmly when securing or releasing the latches on the Lid!

The following render shows the printed TPU Lid Gasket:

The following render shows the TPU Lid Gasket above the slot in the Lid where it will be inserted. It doesn't matter which side of the TPU Lid Gasket is up or down, since the side walls primarily create the seal:

The following render shows the TPU Lid Gasket partially inserted in the Lid. Push it down gently with a small tool such as a screwdriver until it rests at the bottom of the slot:

The following render shows the TPU Lid Gasket fully inserted in the Lid:

The following photo shows the TPU Lid Gasket resting sideways on the Lid to illustrate how flexible an 85A TPU Lid Gasket will be;  a 95A TPU Lid Gasket isn't quite as soft, so you need to use a 0.4mm nozzle if using 95A TPU to successfully replace the silicone foam seal from Mark's design:

The following photo shows the TPU Lid partially inserted in the Lid:

The following photo shows the TPU Lid fully inserted in the Lid:

To allow modifications, I have provided a STEP (.stp) file.

A 3MF file has been provided for Prusa Slicer (has "-Prusa" in the filename) and for Bambu Studio (has "-Bambu" in the filename).

The TPU Lid Gasket seen in the photos was printed with Light Cyan Bambu Lab 85A TPU with a 0.6mm nozzle at 0.18mm layer height (0.2mm layer height for Prusa Slicer version), a 0% infill, 1 perimeter, and 2 top and bottom layers. It was printed on a Textured PEI build plate with a Kores glue stick used to allow easy removal from the build plate. Supports and brims are not needed and must be avoided due to TPU's stickiness.

I also printed and tested a TPU Lid Gasket  with Giantarm 95A TPU with a 0.4mm nozzle at 0.2mm layer height, a 0% infill, 1 perimeter, and 2 top and bottom layers. It was printed on a Textured PEI build plate with a Kores glue stick used to allow easy removal from the build plate. Supports and brims are not needed and must be avoided due to TPU's stickiness.

Be sure to check out my other designs - including universal key covers and a diverse collection of household accessories and 3D printing tools - on Printables at https://www.printables.com/@PhilCaruso/models AND on MakerWorld at https://makerworld.com/en/@PhilCaruso

Tagi